Study guide

9.4 Engineered Wood, Trusses, and Load Paths

NASCLA Contractor Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Coverage Map & Exam Overview

Coverage Map & Exam Overview

2 Business Organization, Licensing & Law

1.1 Business Entity Types and Formation 1.2 NASCLA Trade-Exam Waiver and Agency Licensing Boundaries 1.3 Construction Contract Law and Types of Contracts 1.4 Lien Law, Bond Claims, and Dispute Resolution

3 Financial Management, Tax & Labor Law

2.1 Financial Statements, Job Costing, and Cash Flow 2.2 Payroll, Federal/State Tax, and Recordkeeping 2.3 Labor & Employment Law (FLSA, immigration/I-9, EEO) 2.4 Insurance, Surety Bonds, and Risk Management

4 Estimating, Bidding & Plan Reading

3.1 Reading Construction Drawings and Specifications (CSI MasterFormat) 3.2 Quantity Takeoff and Material Estimating 3.3 Bidding, Markup, Overhead, and Profit 3.4 Change Orders, Allowances, and Unit Pricing

5 Project Management & Scheduling

4.1 Project Delivery Methods and the Submittal/RFI Process 4.2 Scheduling (CPM, Bar Charts, Critical Path) 4.3 Quality Control, Inspections, and Closeout 4.4 Permits, Codes, and the Inspection Process

6 Construction Safety & OSHA (29 CFR 1926)

5.1 OSHA Administration, Recordkeeping, and the General Duty Clause 5.2 Fall Protection, Scaffolds, and Ladders 5.3 Excavation/Trenching, Electrical, and Hazard Communication 5.4 PPE, Fire Protection, Cranes, and Confined Spaces

7 General Requirements & Sitework

6.1 Division 01 General Requirements and Temporary Facilities 6.2 Surveying, Site Layout, and Excavation 6.3 Soils, Compaction, and Erosion/Sediment Control 6.4 Foundations, Footings, and Site Drainage

8 Concrete (CSI Division 03)

7.1 Concrete Materials, Mix Design, and Water-Cement Ratio 7.2 Formwork and Reinforcement Placement 7.3 Placing, Finishing, Curing, and Testing (slump, cylinders) 7.4 Concrete Defects, Joints, and Cold-Weather Practices

9 Masonry (CSI Division 04)

8.1 Masonry Units, Mortar Types (M/S/N/O), and Grout 8.2 Brick and CMU Bonds, Reinforcement, and Coursing 8.3 Lintels, Control/Expansion Joints, and Flashing 8.4 Masonry Estimating and Cold/Hot Weather Construction

10 Metals & Wood (CSI Divisions 05 & 06)

9.1 Structural Steel, Connections, and Welding/Bolting 9.2 Light-Gauge Metal Framing 9.3 Wood Framing, Species/Grades, and Fasteners 9.4 Engineered Wood, Trusses, and Load Paths

11 Thermal & Moisture Protection (CSI Division 07)

10.1 Waterproofing, Dampproofing, and Below-Grade Protection 10.2 Insulation, R-Values, and Vapor Barriers 10.3 Roofing Systems (steep-slope and low-slope) and Underlayment 10.4 Flashing, Sealants, and Air Barriers

12 Openings & Finishes (CSI Divisions 08 & 09)

11.1 Doors, Windows, Glazing, and Hardware 11.2 Gypsum Board, Plaster, and Framing 11.3 Flooring, Tile, and Acoustical Ceilings 11.4 Painting, Coatings, and Finish Schedules

13 Mechanical, Plumbing & Electrical Overview

12.1 Plumbing Systems, Fixtures, and DWV/Supply Basics 12.2 HVAC Systems and Load Concepts 12.3 Electrical Systems, Service, and NEC Basics 12.4 Coordination, Rough-In, and Energy Code

9.4 Engineered Wood, Trusses, and Load Paths

Key Takeaways Explain This Topic AI

Engineered wood (CSI 06 17 00) follows IBC Chapter 23, ICC-ES ESR reports, and ANSI/TPI 1 for trusses.

EWP types (LVL, PSL, LSL, glulam, I-joists) span farther but fail faster in fire; IRC R501.3 requires a gypsum membrane.

Glulam stress class (e.g., 24F-V4) sets Fb and layup; tension laminations go at the bottom of a simple span.

Never field-cut or notch a truss without engineer approval; brace permanently and temporarily per TPI 1/BCSI.

A continuous load path uses rated connectors with manufacturer-specified nails; design uplift uses net uplift.

Last updated: June 2026

9.4 Engineered Wood, Trusses, and Load Paths

Engineered wood products (EWP) and prefabricated wood trusses are CSI Division 06 17 00 (Shop-Fabricated Structural Wood). They are governed by IBC Chapter 23 , the manufacturer's evaluation report (ICC-ES ESR) , and the Truss Plate Institute (TPI) ANSI/TPI 1 standard for metal-plate-connected trusses. EWP design values come from the maker's tables, not generic lumber tables.

Engineered Wood Product Types

  • Product Description Common use
  • LVL (laminated veneer lumber) Veneers glued grain-parallel Beams, headers
  • PSL (parallel strand lumber) Long strands, high strength Heavy beams/columns
  • LSL (laminated strand lumber) Shorter strands Rim board, studs
  • Glulam Glued laminated dimension lumber Long-span beams
  • I-joist OSB/ply web + flanges Floor/roof joists

EWP advantages: longer spans, dimensional stability, less waste. They are highly heat-sensitive in fire — engineered I-joists can fail faster than solid sawn lumber, which is why IRC R501.3 requires a membrane (e.g. 1/2-in gypsum) or sprinklers under engineered floors.

Glulam Grading and Camber

Glulam beams are specified by stress class , e.g. 24F-V4 (24 = allowable bending Fb of 2400 psi; F = bending member; V4 = layup combination). The high-grade laminations go in the tension zone at the bottom of a simple span — installing a glulam upside-down is a serious field error. Glulam is usually fabricated with camber (a slight upward curve) to offset dead-load deflection, and comes in appearance grades — Industrial, Architectural, Premium — selected for how exposed the member will be.

I-joists are governed by APA/ASTM D5055 ; they must never be cut through the flange, and web holes are limited to the manufacturer's hole chart (large holes only near mid-span where shear is low). Rim board and squash blocks transfer bearing loads around I-joist ends and prevent rotation at supports.

Trusses and TPI 1

Metal-plate-connected wood trusses are engineered by the truss design engineer and shipped with sealed truss design drawings . Key field rules per TPI 1 and BCSI (Building Component Safety Information):

Never cut, drill, or notch a truss member or chord in the field without engineer approval — it voids the design.

Trusses require permanent and temporary bracing to prevent buckling; the lateral restraint and diagonal bracing are part of the engineering.

The truss layout/placement diagram is for installation only — it is not an engineering document.

Load Path and Lateral Connectors

A continuous load path carries gravity and lateral (wind/seismic) loads from roof to foundation: roof/truss to wall, wall to floor, floor to wall below, wall to foundation. Each transfer needs a positive mechanical connection. Common metal connectors (e.g. Simpson Strong-Tie, USP) include:

Joist hangers (face-mount/top-flange) for joist-to-beam.

Hurricane/seismic ties (H-clips, twist straps) for truss/rafter-to-top-plate uplift.

Hold-downs and anchor bolts for shear-wall-to-foundation.

Connectors must use the manufacturer-specified nails (often 10d x 1-1/2 in in hangers) — substituting shorter or fewer nails cuts the rated capacity.

Uplift Worked Example

Wind uplift creates net upward force on the roof. If a truss carries 400 lb of dead load but wind produces 650 lb uplift at the bearing, the net uplift = 650 - 400 = 250 lb . The chosen hurricane tie must have a listed uplift capacity (e.g. H2.5A ≈ 415 lb ) exceeding 250 lb with the code load factor. Selecting a connector below the net uplift demand is a costly practical failure.

Lateral resistance flows through shear walls (sheathed with rated wood structural panels) and diaphragms (roof and floor sheathing acting as horizontal beams). Sheathing nailing — edge and field spacing, e.g. 8d at 6 in edges / 12 in field — sets the shear capacity per the IBC nailing/shear-wall tables; tightening edge nailing to 4 or 3 in increases capacity. Drag struts (collectors) carry diaphragm forces into shear walls, and hold-downs resist the resulting overturning at wall ends, completing the lateral load path to the foundation.