Study guide
11.1 Doors, Windows, Glazing, and Hardware
NASCLA Contractor Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Coverage Map & Exam Overview
Coverage Map & Exam Overview
2 Business Organization, Licensing & Law
1.1 Business Entity Types and Formation 1.2 NASCLA Trade-Exam Waiver and Agency Licensing Boundaries 1.3 Construction Contract Law and Types of Contracts 1.4 Lien Law, Bond Claims, and Dispute Resolution
3 Financial Management, Tax & Labor Law
2.1 Financial Statements, Job Costing, and Cash Flow 2.2 Payroll, Federal/State Tax, and Recordkeeping 2.3 Labor & Employment Law (FLSA, immigration/I-9, EEO) 2.4 Insurance, Surety Bonds, and Risk Management
4 Estimating, Bidding & Plan Reading
3.1 Reading Construction Drawings and Specifications (CSI MasterFormat) 3.2 Quantity Takeoff and Material Estimating 3.3 Bidding, Markup, Overhead, and Profit 3.4 Change Orders, Allowances, and Unit Pricing
5 Project Management & Scheduling
4.1 Project Delivery Methods and the Submittal/RFI Process 4.2 Scheduling (CPM, Bar Charts, Critical Path) 4.3 Quality Control, Inspections, and Closeout 4.4 Permits, Codes, and the Inspection Process
6 Construction Safety & OSHA (29 CFR 1926)
5.1 OSHA Administration, Recordkeeping, and the General Duty Clause 5.2 Fall Protection, Scaffolds, and Ladders 5.3 Excavation/Trenching, Electrical, and Hazard Communication 5.4 PPE, Fire Protection, Cranes, and Confined Spaces
7 General Requirements & Sitework
6.1 Division 01 General Requirements and Temporary Facilities 6.2 Surveying, Site Layout, and Excavation 6.3 Soils, Compaction, and Erosion/Sediment Control 6.4 Foundations, Footings, and Site Drainage
8 Concrete (CSI Division 03)
7.1 Concrete Materials, Mix Design, and Water-Cement Ratio 7.2 Formwork and Reinforcement Placement 7.3 Placing, Finishing, Curing, and Testing (slump, cylinders) 7.4 Concrete Defects, Joints, and Cold-Weather Practices
9 Masonry (CSI Division 04)
8.1 Masonry Units, Mortar Types (M/S/N/O), and Grout 8.2 Brick and CMU Bonds, Reinforcement, and Coursing 8.3 Lintels, Control/Expansion Joints, and Flashing 8.4 Masonry Estimating and Cold/Hot Weather Construction
10 Metals & Wood (CSI Divisions 05 & 06)
9.1 Structural Steel, Connections, and Welding/Bolting 9.2 Light-Gauge Metal Framing 9.3 Wood Framing, Species/Grades, and Fasteners 9.4 Engineered Wood, Trusses, and Load Paths
11 Thermal & Moisture Protection (CSI Division 07)
10.1 Waterproofing, Dampproofing, and Below-Grade Protection 10.2 Insulation, R-Values, and Vapor Barriers 10.3 Roofing Systems (steep-slope and low-slope) and Underlayment 10.4 Flashing, Sealants, and Air Barriers
12 Openings & Finishes (CSI Divisions 08 & 09)
11.1 Doors, Windows, Glazing, and Hardware 11.2 Gypsum Board, Plaster, and Framing 11.3 Flooring, Tile, and Acoustical Ceilings 11.4 Painting, Coatings, and Finish Schedules
13 Mechanical, Plumbing & Electrical Overview
12.1 Plumbing Systems, Fixtures, and DWV/Supply Basics 12.2 HVAC Systems and Load Concepts 12.3 Electrical Systems, Service, and NEC Basics 12.4 Coordination, Rough-In, and Energy Code
11.1 Doors, Windows, Glazing, and Hardware
Key Takeaways Explain This Topic AI
Egress doors require a minimum 32-inch clear width and 80-inch clear height; doors serving an occupant load of 50 or more swing in the direction of egress travel (IBC Chapter 10).
Fire-door ratings are a fraction of the wall rating (e.g., 3 hr door in a 4 hr fire wall) and must be self-closing, self-latching, and labeled per NFPA 80.
Safety glazing (tempered or laminated) is required in doors, near doors, in low walking-surface locations, and wet areas per IBC Chapter 24.
R-value equals 1 divided by U-factor; lower U-factor and lower SHGC mean better window energy performance per the NFRC label.
ADA/ICC A117.1 favors lever hardware; panic hardware is required for Group A and E occupancies with 50-plus occupants.
Last updated: June 2026
Doors, Windows, Glazing, and Hardware
Construction Specifications Institute (CSI) Division 08 — Openings covers doors, frames, windows, glazing, and door hardware. This editorial section cross-references this material against the International Building Code (IBC) Chapters 7 (fire-rated assemblies), 10 (egress), and 24 (glazing). Because this is an open-book exam, learn where the rule lives, not just the number.
Egress door requirements (IBC Chapter 10)
Egress doors must be side-hinged swinging in most occupancies. Memorize the dimensional limits:
Clear width: minimum 32 inches (door open 90 degrees, measured face of door to stop).
Clear height: minimum 80 inches.
Single leaf max width: 48 inches nominal.
Swing direction: doors serving an occupant load of 50 or more , or a Group H occupancy, must swing in the direction of egress travel.
A common trap: a 36-inch door does not give 36 inches clear — subtract the stop and the door thickness. Expect about 32 to 34 inches clear, which still satisfies code.
Fire door assemblies (IBC Chapter 7, NFPA 80)
Fire-door ratings are a fraction of the wall rating because doors close to interrupt fire, not contain it indefinitely. Use this table for reference navigation:
- Wall assembly rating Required door rating Typical use
- 4 hr 3 hr Fire walls
- 3 hr 3 hr Fire walls (alt.)
- 2 hr 1-1/2 hr Shaft, exit enclosure
- 1 hr exit enclosure 1 hr Stairways
- 1 hr (other) 3/4 hr Corridor, smoke barrier
- 1/2 hr 1/3 hr (20 min) Corridor (smoke)
Fire doors are self-closing and self-latching and carry a permanent label. Field modification voids the label.
Glazing and safety glazing (IBC Chapter 24)
Safety glazing (tempered or laminated, per ANSI Z97.1 / CPSC 16 CFR 1201 ) is required in hazardous locations :
Glazing in doors and within a 24-inch arc of the door edge if the bottom is below 60 inches.
Glazing where the bottom edge is below 18 inches above the floor (walking-surface rule), the top is above 36 inches, the pane exceeds 9 square feet, and a walking surface is within 36 inches.
Glazing in wet areas (tub/shower) where the bottom edge is below 60 inches.
Tempered glass is roughly 4 times stronger than annealed and breaks into small dice. Laminated glass holds fragments on a polyvinyl-butyral interlayer.
Energy: U-factor, SHGC, and R-value
Window thermal performance is rated by U-factor (rate of heat loss — lower is better) and Solar Heat Gain Coefficient (SHGC) (fraction of solar heat admitted — lower reduces cooling load). U-factor is the inverse of R-value : a window with U-0.30 has an effective R of about 3.3 (R = 1 / U). Whole-wall and roof R-values are far higher; do not confuse a U-0.30 window with an R-30 ceiling. National Fenestration Rating Council (NFRC) labels report these values.
Door hardware and accessibility
Under the ICC A117.1 / ADA standard, operable hardware must be usable without tight grasping, pinching, or twisting of the wrist — favor lever handles over knobs. Mounting height for operable parts is 34 to 48 inches above the floor. Panic hardware (listed exit devices) is required on egress doors in assembly (A) and educational (E) occupancies with an occupant load of 50 or more , and in Group H . Maximum opening force for interior non-fire doors is 5 pounds .