Study guide
11.2 Gypsum Board, Plaster, and Framing
NASCLA Contractor Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Coverage Map & Exam Overview
Coverage Map & Exam Overview
2 Business Organization, Licensing & Law
1.1 Business Entity Types and Formation 1.2 NASCLA Trade-Exam Waiver and Agency Licensing Boundaries 1.3 Construction Contract Law and Types of Contracts 1.4 Lien Law, Bond Claims, and Dispute Resolution
3 Financial Management, Tax & Labor Law
2.1 Financial Statements, Job Costing, and Cash Flow 2.2 Payroll, Federal/State Tax, and Recordkeeping 2.3 Labor & Employment Law (FLSA, immigration/I-9, EEO) 2.4 Insurance, Surety Bonds, and Risk Management
4 Estimating, Bidding & Plan Reading
3.1 Reading Construction Drawings and Specifications (CSI MasterFormat) 3.2 Quantity Takeoff and Material Estimating 3.3 Bidding, Markup, Overhead, and Profit 3.4 Change Orders, Allowances, and Unit Pricing
5 Project Management & Scheduling
4.1 Project Delivery Methods and the Submittal/RFI Process 4.2 Scheduling (CPM, Bar Charts, Critical Path) 4.3 Quality Control, Inspections, and Closeout 4.4 Permits, Codes, and the Inspection Process
6 Construction Safety & OSHA (29 CFR 1926)
5.1 OSHA Administration, Recordkeeping, and the General Duty Clause 5.2 Fall Protection, Scaffolds, and Ladders 5.3 Excavation/Trenching, Electrical, and Hazard Communication 5.4 PPE, Fire Protection, Cranes, and Confined Spaces
7 General Requirements & Sitework
6.1 Division 01 General Requirements and Temporary Facilities 6.2 Surveying, Site Layout, and Excavation 6.3 Soils, Compaction, and Erosion/Sediment Control 6.4 Foundations, Footings, and Site Drainage
8 Concrete (CSI Division 03)
7.1 Concrete Materials, Mix Design, and Water-Cement Ratio 7.2 Formwork and Reinforcement Placement 7.3 Placing, Finishing, Curing, and Testing (slump, cylinders) 7.4 Concrete Defects, Joints, and Cold-Weather Practices
9 Masonry (CSI Division 04)
8.1 Masonry Units, Mortar Types (M/S/N/O), and Grout 8.2 Brick and CMU Bonds, Reinforcement, and Coursing 8.3 Lintels, Control/Expansion Joints, and Flashing 8.4 Masonry Estimating and Cold/Hot Weather Construction
10 Metals & Wood (CSI Divisions 05 & 06)
9.1 Structural Steel, Connections, and Welding/Bolting 9.2 Light-Gauge Metal Framing 9.3 Wood Framing, Species/Grades, and Fasteners 9.4 Engineered Wood, Trusses, and Load Paths
11 Thermal & Moisture Protection (CSI Division 07)
10.1 Waterproofing, Dampproofing, and Below-Grade Protection 10.2 Insulation, R-Values, and Vapor Barriers 10.3 Roofing Systems (steep-slope and low-slope) and Underlayment 10.4 Flashing, Sealants, and Air Barriers
12 Openings & Finishes (CSI Divisions 08 & 09)
11.1 Doors, Windows, Glazing, and Hardware 11.2 Gypsum Board, Plaster, and Framing 11.3 Flooring, Tile, and Acoustical Ceilings 11.4 Painting, Coatings, and Finish Schedules
13 Mechanical, Plumbing & Electrical Overview
12.1 Plumbing Systems, Fixtures, and DWV/Supply Basics 12.2 HVAC Systems and Load Concepts 12.3 Electrical Systems, Service, and NEC Basics 12.4 Coordination, Rough-In, and Energy Code
11.2 Gypsum Board, Plaster, and Framing
Key Takeaways Explain This Topic AI
Type X 5/8-inch gypsum board is the standard board for 1-hour rated assemblies; green board is water-resistant but not waterproof and not a wet-area tile backer.
ASTM C840 caps single-layer screw spacing at 16 inches on walls and 12 inches on ceilings; listed fire-rated designs override general spacing.
GA-214 defines six finish levels (0-5); Level 5 is required under gloss paint or critical raking light to prevent joint photographing.
Three-coat plaster (scratch, brown, finish) is about 7/8 inch over metal lath; veneer plaster is a thin skim over blue board.
Estimate 16-inch o.c. studs with (length x 0.75) + 1, then add for corners and openings; steel studs are coded by web, flange, and mil thickness.
Last updated: June 2026
Gypsum Board, Plaster, and Framing
CSI Division 09 — Finishes opens with interior framing and wall surfacing. This guide pairs gypsum board (drywall) installation with IBC Chapter 25 , ASTM C1396 (board), ASTM C840 (application), and light-gauge steel and wood framing rules. Open-book strategy: tab the gypsum board chapter and the fastener-spacing tables in your reference.
Gypsum board types and uses
Regular board: 1/2 inch and 5/8 inch most common.
Type X: fire-rated, 5/8 inch, contains glass fibers; required in 1-hour rated assemblies .
Type C: enhanced fire resistance for some 2-hour assemblies.
Water-resistant (green board): ASTM C1396 backing in damp areas — not allowed as tile backer over wet showers; use cement board (ASTM C1325) there.
Abuse/impact-resistant: ASTM C1629 for corridors.
A trap: green board is not waterproof and is prohibited on ceilings at wide framing spacing because it sags.
Fastener spacing (ASTM C840)
Maximum fastener spacing depends on whether a wall or ceiling and whether nails or screws are used:
- Location Screws (single layer) Nails
- Walls 16 inches o.c. 8 inches o.c. (edges/field)
Ceilings 12 inches o.c. 7 inches o.c.
For fire-rated assemblies , follow the listed (UL) design spacing exactly — it overrides general tables. Set screw heads slightly below the paper without breaking it; broken paper reduces holding power.
Finishing levels (GA-214)
The Gypsum Association GA-214 standard defines six finish levels, 0 through 5 :
Level 0: no taping/finishing.
Level 1: tape embedded; plenum/concealed areas.
Level 2: tape plus one coat; garages, behind tile.
Level 3: two coats; medium/heavy textures.
Level 4: three coats; flat paints, light textures.
Level 5: skim coat over Level 4; gloss paints and critical lighting.
Practice check: specifying Level 5 under gloss or raking light prevents joint photographing — choosing Level 4 there is the wrong answer.
Plaster systems
Three-coat plaster = scratch, brown, and finish coats over metal lath. Total thickness over metal lath is about 7/8 inch . Veneer plaster is a thin (about 1/16 to 1/8 inch) skim over blue board. Plaster lath and accessories follow ASTM C841/C842 . Mixing water must be potable; over-troweling drives fines to the surface and causes crazing cracks.
Framing and a takeoff scenario
For wood studs at 16 inches on center (o.c.) , estimate studs for a wall as: (wall length in feet x 0.75) + 1 , then add for corners and openings. For a 40-foot wall: 40 x 0.75 = 30, + 1 = 31 studs , plus typically 3 per corner and 2 per opening.
Light-gauge steel studs are specified by web depth, flange, mil thickness, and steel grade (for example 362S162-33, meaning 3-5/8 inch web, 1-5/8 inch flange, 33 mil). Drywall screws into steel must be self-drilling when the stud exceeds 33 mil (20-gauge structural).