Study guide

4.3 Quality Control, Inspections, and Closeout

NASCLA Contractor Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Coverage Map & Exam Overview

Coverage Map & Exam Overview

2 Business Organization, Licensing & Law

1.1 Business Entity Types and Formation 1.2 NASCLA Trade-Exam Waiver and Agency Licensing Boundaries 1.3 Construction Contract Law and Types of Contracts 1.4 Lien Law, Bond Claims, and Dispute Resolution

3 Financial Management, Tax & Labor Law

2.1 Financial Statements, Job Costing, and Cash Flow 2.2 Payroll, Federal/State Tax, and Recordkeeping 2.3 Labor & Employment Law (FLSA, immigration/I-9, EEO) 2.4 Insurance, Surety Bonds, and Risk Management

4 Estimating, Bidding & Plan Reading

3.1 Reading Construction Drawings and Specifications (CSI MasterFormat) 3.2 Quantity Takeoff and Material Estimating 3.3 Bidding, Markup, Overhead, and Profit 3.4 Change Orders, Allowances, and Unit Pricing

5 Project Management & Scheduling

4.1 Project Delivery Methods and the Submittal/RFI Process 4.2 Scheduling (CPM, Bar Charts, Critical Path) 4.3 Quality Control, Inspections, and Closeout 4.4 Permits, Codes, and the Inspection Process

6 Construction Safety & OSHA (29 CFR 1926)

5.1 OSHA Administration, Recordkeeping, and the General Duty Clause 5.2 Fall Protection, Scaffolds, and Ladders 5.3 Excavation/Trenching, Electrical, and Hazard Communication 5.4 PPE, Fire Protection, Cranes, and Confined Spaces

7 General Requirements & Sitework

6.1 Division 01 General Requirements and Temporary Facilities 6.2 Surveying, Site Layout, and Excavation 6.3 Soils, Compaction, and Erosion/Sediment Control 6.4 Foundations, Footings, and Site Drainage

8 Concrete (CSI Division 03)

7.1 Concrete Materials, Mix Design, and Water-Cement Ratio 7.2 Formwork and Reinforcement Placement 7.3 Placing, Finishing, Curing, and Testing (slump, cylinders) 7.4 Concrete Defects, Joints, and Cold-Weather Practices

9 Masonry (CSI Division 04)

8.1 Masonry Units, Mortar Types (M/S/N/O), and Grout 8.2 Brick and CMU Bonds, Reinforcement, and Coursing 8.3 Lintels, Control/Expansion Joints, and Flashing 8.4 Masonry Estimating and Cold/Hot Weather Construction

10 Metals & Wood (CSI Divisions 05 & 06)

9.1 Structural Steel, Connections, and Welding/Bolting 9.2 Light-Gauge Metal Framing 9.3 Wood Framing, Species/Grades, and Fasteners 9.4 Engineered Wood, Trusses, and Load Paths

11 Thermal & Moisture Protection (CSI Division 07)

10.1 Waterproofing, Dampproofing, and Below-Grade Protection 10.2 Insulation, R-Values, and Vapor Barriers 10.3 Roofing Systems (steep-slope and low-slope) and Underlayment 10.4 Flashing, Sealants, and Air Barriers

12 Openings & Finishes (CSI Divisions 08 & 09)

11.1 Doors, Windows, Glazing, and Hardware 11.2 Gypsum Board, Plaster, and Framing 11.3 Flooring, Tile, and Acoustical Ceilings 11.4 Painting, Coatings, and Finish Schedules

13 Mechanical, Plumbing & Electrical Overview

12.1 Plumbing Systems, Fixtures, and DWV/Supply Basics 12.2 HVAC Systems and Load Concepts 12.3 Electrical Systems, Service, and NEC Basics 12.4 Coordination, Rough-In, and Energy Code

4.3 Quality Control, Inspections, and Closeout

Key Takeaways Explain This Topic AI

QC is the contractor's in-process checking; QA is the owner/A/E verification of that system.

IBC Chapter 17 Special Inspectors are independent, report to the building official and A/E, and a final report precedes the C of O.

Concrete: 27 ft³/yd³, ASTM C39 cylinders broken at 7/28 days, lower w/c ratio means higher strength.

ASTM C270 mortar: Type M/S below grade, Type N above grade, Type O interior non-load-bearing only.

Substantial Completion triggers warranties and stops liquidated damages; closeout needs as-builts, O&M, lien waivers, and surety consent.

Last updated: June 2026

Quality Control vs. Quality Assurance

Quality Control (QC) — the contractor's in-process checks that work meets the Contract Documents (e.g., slump tests, torque checks).

Quality Assurance (QA) — the owner/A/E program that verifies the QC system works (audits, third-party testing).

Practice check: testing labs hired by the owner perform QA ; the GC still owns QC and the means and methods.

Special Inspections (IBC Chapter 17)

IBC Chapter 17 requires Special Inspections for designated work — concrete, masonry, structural steel/welding, high-strength bolting, soils/deep foundations, and fire-resistant materials. The Special Inspector is qualified, approved by the building official, and reports directly to the building official and the A/E , not the contractor. A Statement of Special Inspections is part of the permit set, and a Final Report is required before the Certificate of Occupancy.

Concrete QC numerics

Slump test — ASTM C143; typical structural slump 3–5 in.

Compressive cylinders — ASTM C39; standard set broken at 7 and 28 days ; f'c acceptance based on 28-day strength.

Water-cement (w/c) ratio — lower w/c = higher strength/durability; a 0.45 w/c gives higher strength than 0.55.

Worked yield: 1 yd³ concrete = 27 ft³ . A slab 40 ft × 30 ft × 4 in (0.333 ft) = 400 ft³ ÷ 27 = 14.8 yd³ ; order ~ 16 yd³ (≈8% waste).

Masonry and mortar QC

Mortar types follow ASTM C270 proportions. Higher letter strength = more Portland cement:

  • Mortar Approx. compressive Typical use
  • Type M 2,500 psi Foundations, retaining walls (below grade)
  • Type S 1,800 psi Structural, at/below grade, high lateral load
  • Type N 750 psi General above-grade exterior/interior
  • Type O 350 psi Interior, non-load-bearing only

Trap: do not use Type O below grade; use Type M or S where soil and water loads act.

Punch List and Substantial Completion

Substantial Completion — the owner can occupy/use the project for its intended purpose; it starts warranties, transfers risk of loss, and stops most liquidated damages.

Punch List — the A/E's list of incomplete/defective items finished before final payment.

Final Completion — all punch items done, closeout documents delivered.

Closeout Documents

Deliver before final payment and Certificate of Occupancy:

  • As-built / record drawings showing field changes
  • O&M (Operation & Maintenance) manuals
  • Warranties and guarantees
  • Affidavit of payment / lien waivers from subs and suppliers
  • Consent of surety to final payment
  • Special Inspection final report and certificates of compliance
  • Attic stock / spare materials and keys

Retainage and final payment

Retainage (commonly 5–10% ) is withheld from each progress payment and released at or after substantial/final completion. On a $1,200,000 contract at 10% retainage, $120,000 is held; partial release at substantial completion often reduces it (e.g., to 5%). Final payment generally requires lien waivers and the consent of surety to protect the owner.