Study guide

6.2 Surveying, Site Layout, and Excavation

NASCLA Contractor Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Coverage Map & Exam Overview

Coverage Map & Exam Overview

2 Business Organization, Licensing & Law

1.1 Business Entity Types and Formation 1.2 NASCLA Trade-Exam Waiver and Agency Licensing Boundaries 1.3 Construction Contract Law and Types of Contracts 1.4 Lien Law, Bond Claims, and Dispute Resolution

3 Financial Management, Tax & Labor Law

2.1 Financial Statements, Job Costing, and Cash Flow 2.2 Payroll, Federal/State Tax, and Recordkeeping 2.3 Labor & Employment Law (FLSA, immigration/I-9, EEO) 2.4 Insurance, Surety Bonds, and Risk Management

4 Estimating, Bidding & Plan Reading

3.1 Reading Construction Drawings and Specifications (CSI MasterFormat) 3.2 Quantity Takeoff and Material Estimating 3.3 Bidding, Markup, Overhead, and Profit 3.4 Change Orders, Allowances, and Unit Pricing

5 Project Management & Scheduling

4.1 Project Delivery Methods and the Submittal/RFI Process 4.2 Scheduling (CPM, Bar Charts, Critical Path) 4.3 Quality Control, Inspections, and Closeout 4.4 Permits, Codes, and the Inspection Process

6 Construction Safety & OSHA (29 CFR 1926)

5.1 OSHA Administration, Recordkeeping, and the General Duty Clause 5.2 Fall Protection, Scaffolds, and Ladders 5.3 Excavation/Trenching, Electrical, and Hazard Communication 5.4 PPE, Fire Protection, Cranes, and Confined Spaces

7 General Requirements & Sitework

6.1 Division 01 General Requirements and Temporary Facilities 6.2 Surveying, Site Layout, and Excavation 6.3 Soils, Compaction, and Erosion/Sediment Control 6.4 Foundations, Footings, and Site Drainage

8 Concrete (CSI Division 03)

7.1 Concrete Materials, Mix Design, and Water-Cement Ratio 7.2 Formwork and Reinforcement Placement 7.3 Placing, Finishing, Curing, and Testing (slump, cylinders) 7.4 Concrete Defects, Joints, and Cold-Weather Practices

9 Masonry (CSI Division 04)

8.1 Masonry Units, Mortar Types (M/S/N/O), and Grout 8.2 Brick and CMU Bonds, Reinforcement, and Coursing 8.3 Lintels, Control/Expansion Joints, and Flashing 8.4 Masonry Estimating and Cold/Hot Weather Construction

10 Metals & Wood (CSI Divisions 05 & 06)

9.1 Structural Steel, Connections, and Welding/Bolting 9.2 Light-Gauge Metal Framing 9.3 Wood Framing, Species/Grades, and Fasteners 9.4 Engineered Wood, Trusses, and Load Paths

11 Thermal & Moisture Protection (CSI Division 07)

10.1 Waterproofing, Dampproofing, and Below-Grade Protection 10.2 Insulation, R-Values, and Vapor Barriers 10.3 Roofing Systems (steep-slope and low-slope) and Underlayment 10.4 Flashing, Sealants, and Air Barriers

12 Openings & Finishes (CSI Divisions 08 & 09)

11.1 Doors, Windows, Glazing, and Hardware 11.2 Gypsum Board, Plaster, and Framing 11.3 Flooring, Tile, and Acoustical Ceilings 11.4 Painting, Coatings, and Finish Schedules

13 Mechanical, Plumbing & Electrical Overview

12.1 Plumbing Systems, Fixtures, and DWV/Supply Basics 12.2 HVAC Systems and Load Concepts 12.3 Electrical Systems, Service, and NEC Basics 12.4 Coordination, Rough-In, and Energy Code

6.2 Surveying, Site Layout, and Excavation

Key Takeaways Explain This Topic AI

Use the 3-4-5 rule (or 6-8-10, 9-12-15 multiples) to verify square building corners during layout.

Height of Instrument = known elevation + backsight; unknown elevation = HI − foresight; a higher rod reading means lower ground.

OSHA Subpart P requires a protective system at 5 ft depth and an engineered design at 20 ft depth.

Maximum allowable slopes: Type A = 3/4:1, Type B = 1:1, Type C = 1.5:1 (horizontal:vertical).

Keep spoil piles at least 2 ft from the trench edge and provide egress within 25 ft in trenches 4 ft or deeper.

Last updated: June 2026

Surveying, Site Layout, and Excavation

Site layout translates the drawings to the ground. The contractor establishes a benchmark (a fixed point of known elevation) and a baseline or control point from the survey, then lays out building corners using batter boards set back from the excavation. Layout accuracy is verified by the 3-4-5 rule for square corners: a triangle with legs 3 and 4 and a hypotenuse of 5 forms a perfect right angle. Multiples such as 6-8-10 or 9-12-15 are used for larger buildings.

Elevations, grades, and the leveling instrument

Elevations are read with an automatic level or laser level and a stadia/leveling rod . This editorial practice distinguishes two terms:

Backsight (BS) — the rod reading taken on a point of known elevation (the benchmark).

Foresight (FS) — the rod reading on a point of unknown elevation.

Height of Instrument (HI) = Known elevation + BS.

Unknown elevation = HI − FS.

Worked example: benchmark elevation 100.00 ft , backsight reads 4.50 ft , so HI = 104.50 ft . A foresight on the footing point reads 6.20 ft , so that point sits at 104.50 − 6.20 = 98.30 ft . A higher rod reading always means a lower ground elevation — a common reversal trap.

Excavation classification and protective systems

Excavation is governed by OSHA 29 CFR 1926 Subpart P . A competent person must classify the soil and select a protective system.

  • Item Rule
  • Protective system trigger Trenches 5 ft deep or more (1926.652)
  • Engineer required Any excavation 20 ft deep or deeper needs a registered professional engineer design
  • Spoil pile setback Keep at least 2 ft from the trench edge (1926.651(j))
  • Daily inspection Competent person inspects before each shift and after rain
  • Access/egress Ladder, ramp, or stairway within 25 ft of lateral travel in trenches 4 ft+ deep

Protective options are sloping , benching , shoring , or a trench box (shield) .

Maximum allowable slopes by soil type

OSHA Subpart P, Appendix B lists slope ratios (horizontal:vertical) for excavations up to 20 ft:

  • Soil type Max allowable slope (H:V) Angle
  • Stable rock Vertical 90°
  • Type A 3/4 : 1 53°
  • Type B 1 : 1 45°
  • Type C 1.5 : 1 34°

A Type C trench 10 ft deep must be sloped back 1.5 × 10 = 15 ft on each side, widening the top of the cut by 30 ft total. Misreading the ratio (using 1:1.5 instead of 1.5:1) is a frequent error in takeoff and safety questions alike.