Study guide

6.4 Foundations, Footings, and Site Drainage

NASCLA Contractor Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Coverage Map & Exam Overview

Coverage Map & Exam Overview

2 Business Organization, Licensing & Law

1.1 Business Entity Types and Formation 1.2 NASCLA Trade-Exam Waiver and Agency Licensing Boundaries 1.3 Construction Contract Law and Types of Contracts 1.4 Lien Law, Bond Claims, and Dispute Resolution

3 Financial Management, Tax & Labor Law

2.1 Financial Statements, Job Costing, and Cash Flow 2.2 Payroll, Federal/State Tax, and Recordkeeping 2.3 Labor & Employment Law (FLSA, immigration/I-9, EEO) 2.4 Insurance, Surety Bonds, and Risk Management

4 Estimating, Bidding & Plan Reading

3.1 Reading Construction Drawings and Specifications (CSI MasterFormat) 3.2 Quantity Takeoff and Material Estimating 3.3 Bidding, Markup, Overhead, and Profit 3.4 Change Orders, Allowances, and Unit Pricing

5 Project Management & Scheduling

4.1 Project Delivery Methods and the Submittal/RFI Process 4.2 Scheduling (CPM, Bar Charts, Critical Path) 4.3 Quality Control, Inspections, and Closeout 4.4 Permits, Codes, and the Inspection Process

6 Construction Safety & OSHA (29 CFR 1926)

5.1 OSHA Administration, Recordkeeping, and the General Duty Clause 5.2 Fall Protection, Scaffolds, and Ladders 5.3 Excavation/Trenching, Electrical, and Hazard Communication 5.4 PPE, Fire Protection, Cranes, and Confined Spaces

7 General Requirements & Sitework

6.1 Division 01 General Requirements and Temporary Facilities 6.2 Surveying, Site Layout, and Excavation 6.3 Soils, Compaction, and Erosion/Sediment Control 6.4 Foundations, Footings, and Site Drainage

8 Concrete (CSI Division 03)

7.1 Concrete Materials, Mix Design, and Water-Cement Ratio 7.2 Formwork and Reinforcement Placement 7.3 Placing, Finishing, Curing, and Testing (slump, cylinders) 7.4 Concrete Defects, Joints, and Cold-Weather Practices

9 Masonry (CSI Division 04)

8.1 Masonry Units, Mortar Types (M/S/N/O), and Grout 8.2 Brick and CMU Bonds, Reinforcement, and Coursing 8.3 Lintels, Control/Expansion Joints, and Flashing 8.4 Masonry Estimating and Cold/Hot Weather Construction

10 Metals & Wood (CSI Divisions 05 & 06)

9.1 Structural Steel, Connections, and Welding/Bolting 9.2 Light-Gauge Metal Framing 9.3 Wood Framing, Species/Grades, and Fasteners 9.4 Engineered Wood, Trusses, and Load Paths

11 Thermal & Moisture Protection (CSI Division 07)

10.1 Waterproofing, Dampproofing, and Below-Grade Protection 10.2 Insulation, R-Values, and Vapor Barriers 10.3 Roofing Systems (steep-slope and low-slope) and Underlayment 10.4 Flashing, Sealants, and Air Barriers

12 Openings & Finishes (CSI Divisions 08 & 09)

11.1 Doors, Windows, Glazing, and Hardware 11.2 Gypsum Board, Plaster, and Framing 11.3 Flooring, Tile, and Acoustical Ceilings 11.4 Painting, Coatings, and Finish Schedules

13 Mechanical, Plumbing & Electrical Overview

12.1 Plumbing Systems, Fixtures, and DWV/Supply Basics 12.2 HVAC Systems and Load Concepts 12.3 Electrical Systems, Service, and NEC Basics 12.4 Coordination, Rough-In, and Energy Code

6.4 Foundations, Footings, and Site Drainage

Key Takeaways Explain This Topic AI

Exterior footings must bear below the frost line (IBC 1809.5) to prevent frost heave; interior heated footings are exempt.

1 cubic yard = 27 cubic feet; compute footing volume in cubic feet then divide by 27 and add waste.

Lower water-cement ratio means higher strength; f'c is tested on cylinders per ASTM C39 at 28 days.

Footing width = wall load (plf) ÷ allowable soil bearing (psf); weaker soil requires a wider footing.

Slope finished grade 6 in within 10 ft away from the foundation; use waterproofing (not dampproofing) under hydrostatic pressure.

Last updated: June 2026

Foundations, Footings, and Site Drainage

Foundations transfer building loads into the soil. The footing spreads the load over enough bearing area; the foundation wall or pier carries it down to the footing. Footings must rest below the local frost line — IBC 1809.5 requires the bottom of exterior footings to extend below the frost depth (commonly 12–48 in depending on climate) to prevent frost heave . Interior footings in heated buildings are exempt from frost depth.

Concrete basics: yield, water-cement ratio, strength

Concrete quantities are measured in cubic yards (CY) : 1 CY = 27 cubic feet . A footing 2 ft wide × 1 ft deep × 100 ft long = 200 cu ft ÷ 27 = 7.4 CY (order ~8 CY with waste).

Key relationships:

Water-cement (w/c) ratio — lower ratio = higher strength and durability. A 0.45 w/c mix is far stronger than 0.60 ; excess water weakens concrete and causes bleeding.

Compressive strength (f'c) — tested on cylinders per ASTM C39 at 28 days ; residential footings often 2,500 psi , commercial slabs 3,000–4,000 psi .

Slump — measured per ASTM C143 ; typical footing slump 3–5 in . Adding water on site to raise slump is the classic strength-killing trap.

Footing sizing and reinforcement

Footing width is set so soil pressure stays below the allowable bearing value.

Worked example: a wall delivers 6,000 lb per linear foot onto soil rated 2,000 psf . Required footing width = load ÷ bearing = 6,000 ÷ 2,000 = 3 ft wide . If the soil were only 1,500 psf , width grows to 4 ft .

Reinforcement reference notes:

  • Item Rule of thumb
  • Concrete cover (cast against earth) 3 in (ACI 318)
  • Cover (formed, exposed to earth/weather) 1.5–2 in
  • Footing thickness ≥ width of projection, min 6 in residential
  • Anchor bolts 1/2 in min, embed 7 in, max 6 ft o.c. (IRC/IBC)

Site drainage and foundation moisture control

Water is the foundation's enemy. Code and good practice require moving it away:

Final grade slope — IBC 1804.4 / IRC R401.3 : slope ground away from the foundation a minimum of 6 in within the first 10 ft (a 5% slope).

Foundation drain — perforated pipe in washed gravel at the footing, draining to daylight or a sump, required where the water table is high.

Dampproofing vs waterproofing — dampproofing resists moisture vapor; waterproofing (IBC 1805) resists hydrostatic pressure and is required where a high water table exists.

Backfill — compact in lifts and slope; never backfill before the first-floor framing braces the wall, or the wall can be pushed in.