Study guide
10.2 Insulation, R-Values, and Vapor Barriers
NASCLA Contractor Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Coverage Map & Exam Overview
Coverage Map & Exam Overview
2 Business Organization, Licensing & Law
1.1 Business Entity Types and Formation 1.2 NASCLA Trade-Exam Waiver and Agency Licensing Boundaries 1.3 Construction Contract Law and Types of Contracts 1.4 Lien Law, Bond Claims, and Dispute Resolution
3 Financial Management, Tax & Labor Law
2.1 Financial Statements, Job Costing, and Cash Flow 2.2 Payroll, Federal/State Tax, and Recordkeeping 2.3 Labor & Employment Law (FLSA, immigration/I-9, EEO) 2.4 Insurance, Surety Bonds, and Risk Management
4 Estimating, Bidding & Plan Reading
3.1 Reading Construction Drawings and Specifications (CSI MasterFormat) 3.2 Quantity Takeoff and Material Estimating 3.3 Bidding, Markup, Overhead, and Profit 3.4 Change Orders, Allowances, and Unit Pricing
5 Project Management & Scheduling
4.1 Project Delivery Methods and the Submittal/RFI Process 4.2 Scheduling (CPM, Bar Charts, Critical Path) 4.3 Quality Control, Inspections, and Closeout 4.4 Permits, Codes, and the Inspection Process
6 Construction Safety & OSHA (29 CFR 1926)
5.1 OSHA Administration, Recordkeeping, and the General Duty Clause 5.2 Fall Protection, Scaffolds, and Ladders 5.3 Excavation/Trenching, Electrical, and Hazard Communication 5.4 PPE, Fire Protection, Cranes, and Confined Spaces
7 General Requirements & Sitework
6.1 Division 01 General Requirements and Temporary Facilities 6.2 Surveying, Site Layout, and Excavation 6.3 Soils, Compaction, and Erosion/Sediment Control 6.4 Foundations, Footings, and Site Drainage
8 Concrete (CSI Division 03)
7.1 Concrete Materials, Mix Design, and Water-Cement Ratio 7.2 Formwork and Reinforcement Placement 7.3 Placing, Finishing, Curing, and Testing (slump, cylinders) 7.4 Concrete Defects, Joints, and Cold-Weather Practices
9 Masonry (CSI Division 04)
8.1 Masonry Units, Mortar Types (M/S/N/O), and Grout 8.2 Brick and CMU Bonds, Reinforcement, and Coursing 8.3 Lintels, Control/Expansion Joints, and Flashing 8.4 Masonry Estimating and Cold/Hot Weather Construction
10 Metals & Wood (CSI Divisions 05 & 06)
9.1 Structural Steel, Connections, and Welding/Bolting 9.2 Light-Gauge Metal Framing 9.3 Wood Framing, Species/Grades, and Fasteners 9.4 Engineered Wood, Trusses, and Load Paths
11 Thermal & Moisture Protection (CSI Division 07)
10.1 Waterproofing, Dampproofing, and Below-Grade Protection 10.2 Insulation, R-Values, and Vapor Barriers 10.3 Roofing Systems (steep-slope and low-slope) and Underlayment 10.4 Flashing, Sealants, and Air Barriers
12 Openings & Finishes (CSI Divisions 08 & 09)
11.1 Doors, Windows, Glazing, and Hardware 11.2 Gypsum Board, Plaster, and Framing 11.3 Flooring, Tile, and Acoustical Ceilings 11.4 Painting, Coatings, and Finish Schedules
13 Mechanical, Plumbing & Electrical Overview
12.1 Plumbing Systems, Fixtures, and DWV/Supply Basics 12.2 HVAC Systems and Load Concepts 12.3 Electrical Systems, Service, and NEC Basics 12.4 Coordination, Rough-In, and Energy Code
10.2 Insulation, R-Values, and Vapor Barriers
Key Takeaways Explain This Topic AI
R-values add in series for assemblies; U-factor = 1/R-total measures transmission.
Thickness needed = target R divided by the material's R-per-inch (e.g., R-30 / 6 = 5 in. polyiso).
IECC prescriptive minimums rise with colder climate zones; '+5ci' denotes continuous insulation against thermal bridging.
Vapor retarders are Class I (<=0.1 perm), II (0.1-1.0), III (1.0-10) per ASTM E96.
In cold climates place the Class I/II vapor retarder on the warm interior side.
Last updated: June 2026
Thermal Resistance Fundamentals
R-value measures resistance to conductive heat flow; higher R = better insulation. U-factor is the inverse (U = 1/R) and measures heat transmission for assemblies, windows, and doors. The local practice contrasts these.
For layered assemblies, R-values add in series : R-total = R1 + R2 + R3... A wall with R-13 batt + R-5 continuous foam sheathing + interior/exterior air films yields roughly R-18 to R-19 nominal.
Common R-Values per Inch
- Material R-value per inch
- Fiberglass batt 3.1 - 3.4
- Cellulose (loose-fill) 3.2 - 3.8
- Expanded polystyrene (EPS) 3.6 - 4.0
- Extruded polystyrene (XPS) 5.0
- Polyisocyanurate (polyiso) 5.6 - 6.5
- Closed-cell spray polyurethane 6.0 - 7.0
- Open-cell spray foam 3.5 - 3.7
Worked example: A roof needs R-30 using polyiso at R-6/in. Required thickness = 30 / 6 = 5 in. If only R-5/in. XPS were used: 30 / 5 = 6 in.
Energy Code Minimums
The International Energy Conservation Code (IECC) sets prescriptive R-values by climate zone. Representative wood-frame wall and ceiling minimums:
- Climate Zone Wall (cavity) Ceiling/Attic
- Zone 2 (hot) R-13 R-38
- Zone 4 (mixed) R-20 or R-13+5ci R-49
- Zone 6 (cold) R-20+5ci R-60
The notation R-13+5ci means R-13 cavity batt plus R-5 continuous insulation over the framing to interrupt thermal bridging through studs.
Vapor Retarders
IBC 1404.3 and IECC R702 classify vapor retarders by permeance (perms, measured per ASTM E96):
- Class I: 0.1 perm or less (sheet polyethylene, foil) - vapor barrier
- Class II: 0.1 to 1.0 perm (kraft-faced batt, vapor-retarder paint)
- Class III: 1.0 to 10 perms (latex paint)
Critical rule: In cold climates (Zones 5-8 and Marine 4), the Class I or II vapor retarder goes on the warm-in-winter (interior) side of the wall to keep moisture from condensing inside the cavity. Placing it on the cold side is a common practical mistake that traps moisture.
Condensation, Dew Point & Continuous Insulation
Vapor moves from warm-humid to cold-dry. If the interior vapor meets a surface below the dew point , it condenses. Continuous exterior insulation keeps the sheathing warmer, moving the dew point outward so condensation does not occur on the structural sheathing.
Scenario: In Zone 6, R-20 cavity + R-5ci satisfies code; but in a vapor-open wall, designers may use Class III (latex paint) interior only when sufficient continuous insulation keeps sheathing above dew point per IECC Table R702.7.1.
Takeoff Example
Insulate a 2,400 ft2 attic floor to R-49 with cellulose at R-3.5/in. Depth = 49 / 3.5 = 14 in. Volume = 2,400 ft2 x (14/12 ft) = 2,800 ft3. If a bag covers 40 ft2 at 14 in., bags = 2,400 / 40 = 60 bags . Always confirm coverage from the manufacturer's chart at the target depth, not a thinner reference depth.