Study guide

10.4 Flashing, Sealants, and Air Barriers

NASCLA Contractor Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Coverage Map & Exam Overview

Coverage Map & Exam Overview

2 Business Organization, Licensing & Law

1.1 Business Entity Types and Formation 1.2 NASCLA Trade-Exam Waiver and Agency Licensing Boundaries 1.3 Construction Contract Law and Types of Contracts 1.4 Lien Law, Bond Claims, and Dispute Resolution

3 Financial Management, Tax & Labor Law

2.1 Financial Statements, Job Costing, and Cash Flow 2.2 Payroll, Federal/State Tax, and Recordkeeping 2.3 Labor & Employment Law (FLSA, immigration/I-9, EEO) 2.4 Insurance, Surety Bonds, and Risk Management

4 Estimating, Bidding & Plan Reading

3.1 Reading Construction Drawings and Specifications (CSI MasterFormat) 3.2 Quantity Takeoff and Material Estimating 3.3 Bidding, Markup, Overhead, and Profit 3.4 Change Orders, Allowances, and Unit Pricing

5 Project Management & Scheduling

4.1 Project Delivery Methods and the Submittal/RFI Process 4.2 Scheduling (CPM, Bar Charts, Critical Path) 4.3 Quality Control, Inspections, and Closeout 4.4 Permits, Codes, and the Inspection Process

6 Construction Safety & OSHA (29 CFR 1926)

5.1 OSHA Administration, Recordkeeping, and the General Duty Clause 5.2 Fall Protection, Scaffolds, and Ladders 5.3 Excavation/Trenching, Electrical, and Hazard Communication 5.4 PPE, Fire Protection, Cranes, and Confined Spaces

7 General Requirements & Sitework

6.1 Division 01 General Requirements and Temporary Facilities 6.2 Surveying, Site Layout, and Excavation 6.3 Soils, Compaction, and Erosion/Sediment Control 6.4 Foundations, Footings, and Site Drainage

8 Concrete (CSI Division 03)

7.1 Concrete Materials, Mix Design, and Water-Cement Ratio 7.2 Formwork and Reinforcement Placement 7.3 Placing, Finishing, Curing, and Testing (slump, cylinders) 7.4 Concrete Defects, Joints, and Cold-Weather Practices

9 Masonry (CSI Division 04)

8.1 Masonry Units, Mortar Types (M/S/N/O), and Grout 8.2 Brick and CMU Bonds, Reinforcement, and Coursing 8.3 Lintels, Control/Expansion Joints, and Flashing 8.4 Masonry Estimating and Cold/Hot Weather Construction

10 Metals & Wood (CSI Divisions 05 & 06)

9.1 Structural Steel, Connections, and Welding/Bolting 9.2 Light-Gauge Metal Framing 9.3 Wood Framing, Species/Grades, and Fasteners 9.4 Engineered Wood, Trusses, and Load Paths

11 Thermal & Moisture Protection (CSI Division 07)

10.1 Waterproofing, Dampproofing, and Below-Grade Protection 10.2 Insulation, R-Values, and Vapor Barriers 10.3 Roofing Systems (steep-slope and low-slope) and Underlayment 10.4 Flashing, Sealants, and Air Barriers

12 Openings & Finishes (CSI Divisions 08 & 09)

11.1 Doors, Windows, Glazing, and Hardware 11.2 Gypsum Board, Plaster, and Framing 11.3 Flooring, Tile, and Acoustical Ceilings 11.4 Painting, Coatings, and Finish Schedules

13 Mechanical, Plumbing & Electrical Overview

12.1 Plumbing Systems, Fixtures, and DWV/Supply Basics 12.2 HVAC Systems and Load Concepts 12.3 Electrical Systems, Service, and NEC Basics 12.4 Coordination, Rough-In, and Energy Code

10.4 Flashing, Sealants, and Air Barriers

Key Takeaways Explain This Topic AI

IBC 1503.2 and 1404.4 require flashing at roof/wall intersections, penetrations, openings, and wall bottoms.

Step, base, counter, valley, drip-edge, and through-wall flashing each serve specific joints; drip edge is required at eaves and rakes.

Masonry weep holes sit directly on through-wall flashing at <=33 in. on center.

Elastomeric sealants (ASTM C920) use a 2:1 width-to-depth ratio with a backer rod to avoid three-sided adhesion.

Air barriers limit air leakage (IECC blower-door ACH50 limits) and are distinct from vapor retarders.

Last updated: June 2026

Flashing Purpose & Code Basis

Flashing is sheet material installed to direct water away from vulnerable joints and penetrations. IBC 1503.2 requires flashing at wall and roof intersections, changes in roof slope or direction, and around roof openings. IBC 1404.4 requires exterior-wall flashing to divert water to the exterior at the bottoms of walls, above openings, and at roof/wall junctions.

Types of Flashing

  • Flashing Location / Purpose
  • Step flashing Sidewalls of sloped roof against vertical wall; one piece per shingle course
  • Base/apron flashing Front of a chimney or wall-to-roof headwall
  • Counter (cap) flashing Set into a masonry reglet, laps over base flashing
  • Valley flashing Open valley where two roof planes meet
  • Drip edge Eaves and rakes; IBC requires drip edge at eaves and gables
  • Through-wall flashing Masonry cavity walls, with weep holes below

Drip edge is now explicitly required by IBC 1507.2.9.3 for asphalt shingle roofs.

Masonry Through-Wall Flashing & Weeps

In cavity/veneer masonry, through-wall flashing collects water that penetrates the outer wythe and directs it out via weep holes . Weep holes are spaced at a maximum of 33 in. on center (TMS 402 / masonry standard) and located immediately above the flashing at the wall base, shelf angles, and over openings.

Drainage check: Weeps must sit directly on top of the flashing - if mortar droppings block them or they sit above the flashing line, drainage fails.

Sealants & Joint Design

Sealants accommodate movement. Per ASTM C920 (elastomeric joint sealants), key chemistries:

Silicone: excellent UV/weather resistance, high movement (+/-50%), glass/metal.

Polyurethane: good adhesion, paintable, abrasion-resistant, +/-25%.

Polysulfide: chemical/fuel resistance.

Acrylic latex: interior, paintable, low movement.

Joint design rule: for working joints, the width-to-depth ratio should be 2:1 (e.g., 1/2 in. wide, 1/4 in. deep). A backer rod (closed-cell foam) controls depth and prevents three-sided adhesion, which would tear the sealant.

Sealant Estimating

Linear coverage of a cartridge depends on bead cross-section. A 10.1 oz cartridge yields about 305 ml (18.6 in3) .

Worked example: A 3/8 in. x 3/8 in. joint = 0.375 x 0.375 = 0.1406 in2 cross-section. Per inch of joint = 0.1406 in3. Linear inches per cartridge = 18.6 / 0.1406 = 132 in = 11 ft . For 220 lin ft of joint: 220 / 11 = 20 cartridges (round up).

Air Barriers

An air barrier is a continuous system limiting uncontrolled air leakage through the building envelope; it improves energy performance and prevents moisture-laden air infiltration. The IECC C402.5 / R402.4 requires a continuous air barrier with sealed penetrations, and prescribes a building air-leakage test (blower door) limit of 3-5 air changes per hour at 50 Pa (ACH50) depending on climate zone.

Key distinction: A material can be both an air barrier and a vapor retarder (e.g., sheet poly), but many air barriers (housewrap) are deliberately vapor-permeable to let walls dry. Do not confuse air leakage with vapor diffusion - they are separate transport mechanisms.