Study guide
6.2 Structural Framing, Trusses & Clearances
NATE Core Knowledge Exam Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Introduction & Exam Overview
1.1 About the NATE Core Knowledge Exam 1.2 Study Strategy & Blueprint Navigation 1.3 HVAC Fundamentals & Math Review
2 Chapter 2: Safety Regulations & Jobsite Practices
2.1 Government & Environmental Regulations 2.2 Personal Safety, PPE & Jobsite Practices 2.3 Moving Machinery & Rotating Equipment Safety
3 Chapter 3: Hazardous Materials, Cylinders & Brazing Safety
3.1 Confined Spaces & Refrigerant Exposure Safety 3.2 Safe Brazing, Soldering & Nitrogen Purging 3.3 Compressed Gas Cylinders, Hazmat & Fire Safety
4 Chapter 4: Hand, Power & Fabrication Tools
4.1 Measurement & Layout Tools 4.2 Fastening & Mechanical Hand Tools 4.3 Sheet Metal Fabrication & Cutting Tools
5 Chapter 5: Copper Tubing Tools & Piping Practices
5.1 Copper Tubing Cutting & Reaming 5.2 Flaring Tools & Mechanical Joints 5.3 Swaging & Tubing Bending
6 Chapter 6: Basic Construction & Building Systems
6.1 Architectural Plans, Specifications & Blueprints 6.2 Structural Framing, Trusses & Clearances 6.3 Building Envelope & Fenestration 6.4 Mechanical Routing, Firestopping & Venting
7 Chapter 7: Basic Science & Thermodynamics
7.1 Matter, Chemistry & Combustion Principles 7.2 Pressure Fundamentals & Gas Laws 7.3 Applied HVAC Physics & Mathematics
8 Chapter 8: Achieving Desired Conditions & Comfort
8.1 Human Thermal Comfort & ASHRAE Standard 55 8.2 Humidity Control & System Psychrometrics 8.3 Ventilation Standards & ASHRAE Standard 62.2
9 Chapter 9: Indoor Air Quality & Acoustic Control
9.1 Air Filtration & MERV Ratings 9.2 Air Cleaning, Odor Control & UVGI 9.3 Sound & Vibration Attenuation
10 Chapter 10: Temperature & Heat Science
10.1 Sensible Heat, Latent Heat & BTU Fundamentals 10.2 Methods of Heat Transfer 10.3 Temperature Measurement Instruments & Calibration
11 Chapter 11: Humidity Measurements & Psychrometrics
11.1 Dry-Bulb, Wet-Bulb & Temperature Splits 11.2 Sling Psychrometers & Humidity Instruments 11.3 Psychrometric Chart Analysis & Enthalpy
12 Chapter 12: Electrical Fundamentals & Schematics
12.1 Electrical Concepts, Ohm's Law & Power 12.2 AC Power, Magnetism & Control Transformers 12.3 Electrical Loads & Power Factor 12.4 Electrical Symbols & Ladder Diagrams
13 Chapter 13: Electric Motors & Field Controls
13.1 Single-Phase Electric Motors & Capacitors 13.2 Three-Phase Motors & Commercial Power 13.3 Variable-Speed ECM Motors & Actuators 13.4 Field Wiring, Contactors & Control Devices
14 Chapter 14: Digital Meters & Electrical Diagnostics
14.1 Digital Multimeters & Safety Ratings 14.2 Voltage Drop, Amperage & Resistance Testing 14.3 Specialized Electrical Diagnostics: Megohmmeter, Capacitance & Micro-Signals
6.2 Structural Framing, Trusses & Clearances
Key Takeaways Explain This Topic AI
Modern residential framing utilizes platform framing (floor-by-floor construction with built-in firestops) rather than older balloon framing (continuous studs creating vertical open fire flues).
Engineered roof trusses are pre-engineered closed structural force systems; technicians must NEVER cut, notch, drill, modify, or remove any chord, web member, or metal gusset plate without prior written approval from a licensed structural engineer.
Solid lumber floor joist notching is strictly prohibited in the middle third of the span; outer third notches cannot exceed 1/6 of joist depth, and end bearing notches cannot exceed 1/4 of joist depth.
Bored holes in solid lumber joists cannot exceed 1/3 of the joist depth and must maintain a minimum 2-inch clearance from both top and bottom edges.
Attic equipment installations require a minimum 22"x30" access opening, a continuous solid 24" wide walkway not exceeding 20 feet, and a 30"x30" level service workspace in front of the unit.
Last updated: September 2026
- 6.2 Structural Framing, Trusses & Clearances
- Structural Framing Systems: Wood and Light-Gauge Steel
HVAC technicians constantly interact with building structural framing when routing ductwork, running refrigerant line sets, suspending fan coil units, coring penetrations, and installing flues. Compromising structural framing to accommodate mechanical equipment can lead to structural deflection, roof sag, floor collapse, and severe liability.
Wood Framing Systems: Platform vs. Balloon Framing
Residential and light commercial structures built with wood framing utilize one of two primary structural topologies: Platform Framing (Modern Standard): Balloon Framing (Historic / Pre-1950s):
- +-------------------------------+ Roof +-------------------------------+ Roof
- | 2nd Floor Studs | | Continuous Studs |
- +===============================+ Subfloor | Run From Sill Plate |
- | 1st Floor Studs | | Straight to Roof Rafters |
- +===============================+ Subfloor | (Open Stud Cavities |
- | Foundation Sill Plate | | Create Vertical Fire Chases) |
- +-------------------------------+ Foundation +-------------------------------+ Foundation
Platform Framing (Western Framing) : The universal modern construction standard. Each story is built as an independent "platform." The foundation supports the first-floor mudsill and floor joists, which are covered by subflooring (plywood or OSB). The first-story wall studs are erected on top of this subfloor platform and capped with double top plates. The second-story floor joists rest directly on these plates, creating a new working deck. Platform framing naturally creates horizontal wood firestops at every floor level, containing fire spread within single stories.
Balloon Framing : Common in two-story homes constructed prior to the 1950s. Wall studs extend continuously from the foundation sill plate all the way up to the roof rafters. Second-story floor joists are hung from a notched ribbon board (ledger) nailed to the continuous studs. Because there are no horizontal plates separating stories, the stud bays form uninterrupted vertical flues from basement to attic. In balloon-framed buildings, HVAC installers must ensure that any penetration through floors or ceilings is sealed with code-compliant fireblocking to prevent these open vertical chases from acting as chimneys during a structure fire.
Light-Gauge Steel Framing
Increasingly common in commercial construction, multi-family housing, and high-density residential structures, light-gauge cold-formed steel (CFS) framing replaces wood dimensional lumber with galvanized steel members:
C-Studs : Vertical framing members with stiffening flanges, resembling the letter 'C'.
Tracks (U-Channels) : Horizontal top and bottom plates that receive and align vertical C-studs.
Fastened exclusively with self-drilling sheet metal screws. Pre-punched factory service punch-outs along the stud web provide routing pathways for electrical wiring and copper piping. Technicians must insert approved plastic grommets into these punch-outs before running copper tubing to prevent galvanic corrosion and mechanical abrasion from sharp steel edges.
Framing Anatomy and Terminology
Understanding structural nomenclature ensures proper communication on the jobsite:
Wall Studs : Vertical framing members ( 2 × 4 2\times4 2 × 4 actual dimension 1.5 ′ ′ × 3.5 ′ ′ 1.5'' \times 3.5'' 1. 5 ′′ × 3. 5 ′′ ; or 2 × 6 2\times6 2 × 6 actual dimension 1.5 ′ ′ × 5.5 ′ ′ 1.5'' \times 5.5'' 1. 5 ′′ × 5. 5 ′′ ), spaced uniformly at 16 inches 16\text{ inches} 16 inches or 24 inches 24\text{ inches} 24 inches on center (O.C.).
Bottom Plate (Sole Plate / Mudsill) : The horizontal framing member anchored to the concrete foundation or subfloor upon which studs stand.
Double Top Plates : Two horizontal 2 × 4 2\times4 2 × 4 or 2 × 6 2\times6 2 × 6 members overlapping at wall corners, tying walls together and providing a structural bearing surface for ceiling joists and rafters.
Structural Headers : Heavy structural beams (doubled dimensional lumber, glulam, or Laminated Veneer Lumber [LVL]) installed horizontally over door and window openings to carry roof and floor loads across the opening.
Jack (Trimmer) Studs & King Studs : Jack studs sit directly beneath the ends of a header to support its vertical downward load. King studs run full height alongside the jack studs to resist lateral forces.
Floor Joists & Ceiling Joists : Horizontal structural members supporting floor decks and drywall ceilings. Solid lumber ( 2 × 8 , 2 × 10 , 2 × 12 2\times8, 2\times10, 2\times12 2 × 8 , 2 × 10 , 2 × 12 ), engineered wood I-joists (TJIs), or open-web floor trusses.
Girders and Beams : Primary horizontal structural members supporting multiple floor joists, transferring building weight to vertical steel or wood columns/posts.
Load-Bearing vs. Non-Load-Bearing Walls
Before an HVAC installer cuts a wall opening for a return air grille, transfers a duct drop, or drills holes for refrigerant lines, they must identify whether the partition is load-bearing.
Identifying Load-Bearing Walls
Orientation Relative to Joists : Walls running perpendicular ( 90 ∘ 90^\circ 9 0 ∘ ) to floor joists or ceiling joists are almost universally load-bearing, as they support the joist spans.
Stacking Alignment : Walls that align directly over basement girders, steel I-beams, foundation walls, or other walls on lower floors are primary load-bearing walls transferring weight to the earth.
Exterior Walls : Virtually all exterior perimeter walls are load-bearing, carrying roof truss, rafter, and upper floor loads.
Non-Load-Bearing (Partition) Walls : Interior dividing walls running parallel to floor and ceiling joists that carry only the weight of their own framing and drywall. However, if a partition wall carries a heavy HVAC air handler hung from the attic above, it becomes a structural load path.
Caution
Consequences of Unauthorized Wall Modifications : Cutting or removing studs in a load-bearing wall to fit a return duct or recessed air handler without engineering a properly sized structural header and temporary shoring will cause floor sagging above, wall drywall cracking, door jamming, and catastrophic structural failure.
Engineered Roof Trusses: The Absolute Structural Rule
Pre-engineered wood roof trusses are precision structural components engineered using advanced finite-element computer modeling. Trusses consist of three primary elements:
Chords : The outer perimeter members. The top chord functions primarily under intense compression and bending loads from roofing materials and snow. The bottom chord acts primarily as a continuous tension tie holding the walls together, while supporting ceiling drywall.
Web Members : The internal diagonal and vertical lumber pieces that triangulate forces between the top and bottom chords, transferring loads through tension and compression.
Gusset Plates (Gang-Nail Plates) : Light-gauge galvanized steel connector plates stamped with dozens of integral teeth per square inch. These plates are pressed into both sides of lumber joints under high hydraulic factory pressure. Engineered Wood Roof Truss Assembly:
- Top Chord (Compression)
- /\ /\
- / \ Web / \ <--- Gusset / Gang-Nail Plates
- / \ (Tension/\ \ at every joint
- / Web \ Comp.)/ \ \
- /________\_____/____\___\
- Bottom Chord (Continuous Tension Tie)
- [ ABSOLUTE RULE: NEVER CUT, NOTCH, OR DRILL ANY MEMBER OF A TRUSS! ]
- The Absolute Structural Rule for HVAC Technicians
NEVER cut, notch, drill, modify, splice, or remove any member (chord or web) of an engineered roof truss under any circumstances without prior written design approval and stamped repair drawings from a licensed structural engineer.
Unlike traditional site-built rafters (which feature significant structural redundancy), an engineered truss operates as a closed structural system . Every single wood member and gusset plate is sized to handle precise mathematical vectors of tension and compression:
Cutting a single web member to route a 16 inch 16\text{ inch} 16 inch round supply duct destroys the entire load distribution matrix.
Forces immediately re-route into adjacent members that were never sized to carry them.
The bottom chord can buckle, the top chord can deflect downward, and under a sudden winter snow load or high wind event, the roof structure can suffer sudden, catastrophic collapse.
The International Residential Code (IRC Section R802.10.4) explicitly mandates: "Truss members and components shall not be cut, notched, drilled, spliced or otherwise altered in any way without written concurrence and approval of a registered design professional."
If a truss web obstructs an HVAC equipment location or duct run, the contractor must route the ductwork around the obstruction, use smaller split ducts, or hire a structural engineer to design a field modification detail involving sistered lumber and steel tie brackets before touching the wood.
Drilling and Notching Structural Wood Members (IRC / IBC Code Rules)
When routing refrigerant lines, condensate pipes, fuel gas lines, and electrical cables through solid wood framing, technicians must comply strictly with International Residential Code (IRC) and International Building Code (IBC) boring and notching limits.
1. Solid Lumber Floor Joist Rules (IRC Section R502.8)
Floor joists act as structural beams under bending stress. When a downward floor load is applied, the top edge of the joist is placed under compression , while the bottom edge is subjected to extreme tension . The center third of the span experiences the highest bending moment. Solid Lumber Joist Span Notching & Boring Zones:
- |<------- Outer Third ------->|<------- Middle Third ------->|<------- Outer Third ------->|
- | End Bearing | | End Bearing |
- | Notch <= D/4 | NO NOTCHING PERMITTED | Notch <= D/4 |
- | Outer Notch <= D/6 (Top) | ANYWHERE IN MIDDLE 1/3! | Outer Notch <= D/6 (Top) |
- | | | |
- | [O] Hole <= D/3 | [O] Hole <= D/3 | [O] Hole <= D/3 |
- | Edge Margin >= 2" | Edge Margin >= 2" | Edge Margin >= 2" |
- +-----------------------------+------------------------------+-----------------------------+
- <--------------------------------------- Total Span --------------------------------------->
Notching Limitations for Joists:
Middle Third Rule : NO NOTCHES ARE PERMITTED in the middle third of the joist span. Notching the bottom edge in the center third cuts directly across the primary tension fibers, drastically reducing joist load capacity and causing immediate cracking.
Outer Thirds : Notches in the outer thirds of the span are permitted only on the top edge , and the notch depth cannot exceed one-sixth of the joist depth ( D / 6 D/6 D /6 ) .
Ends (Bearing Points) : Notches at the bearing ends where the joist rests on a foundation plate or girder cannot exceed one-fourth of the joist depth ( D / 4 D/4 D /4 ) , and the notch length cannot exceed one-third of the joist depth.
Boring (Hole) Limitations for Joists:
Maximum Hole Diameter : The diameter of any bored hole cannot exceed one-third of the actual joist depth ( D / 3 D/3 D /3 ) .
Edge Margin : The edge of any hole must be at least 2 inches 2\text{ inches} 2 inches from the top edge and bottom edge of the joist.
Spacing Between Openings : Holes must be spaced at least 2 inches 2\text{ inches} 2 inches away from any other hole or notch.
Worked Example: Sizing a Hole in a 2x10 Floor Joist
A technician needs to drill a hole through a nominal 2 × 10 2\times10 2 × 10 solid lumber floor joist for a pair of insulated 7 / 8 ′ ′ 7/8'' 7/ 8 ′′ and 3 / 8 ′ ′ 3/8'' 3/ 8 ′′ refrigerant lines.
Identify Actual Dimension : A nominal 2 × 10 2\times10 2 × 10 has an actual lumber depth of D = 9.25 inches D = 9.25\text{ inches} D = 9.25 inches (not 10 inches 10\text{ inches} 10 inches ). Width is 1.5 inches 1.5\text{ inches} 1.5 inches .
Calculate Maximum Hole Diameter : Max Diameter = D 3 = 9.25 ′ ′ 3 = 3.08 inches \text{Max Diameter} = \frac{D}{3} = \frac{9.25''}{3} = 3.08\text{ inches} Max Diameter = 3 D = 3 9.2 5 ′′ = 3.08 inches The technician can safely drill a hole up to 3.0 inches 3.0\text{ inches} 3.0 inches in diameter (using a standard 3 ′ ′ 3'' 3 ′′ hole saw).
Verify Edge Clearances :
With a 3.0 ′ ′ 3.0'' 3. 0 ′′ hole centered vertically in a 9.25 ′ ′ 9.25'' 9.2 5 ′′ joist: Total Remaining Wood = 9.25 ′ ′ − 3.00 ′ ′ = 6.25 ′ ′ \text{Total Remaining Wood} = 9.25'' - 3.00'' = 6.25'' Total Remaining Wood = 9.2 5 ′′ − 3.0 0 ′′ = 6.2 5 ′′ Edge Margin (Top and Bottom) = 6.25 ′ ′ 2 = 3.125 inches \text{Edge Margin (Top and Bottom)} = \frac{6.25''}{2} = 3.125\text{ inches} Edge Margin (Top and Bottom) = 2 6.2 5 ′′ = 3.125 inches
Since 3.125 ′ ′ > 2.0 ′ ′ 3.125'' > 2.0'' 3.12 5 ′′ > 2. 0 ′′ , the clearance exceeds the mandatory 2 inch 2\text{ inch} 2 inch code minimum.
2. Engineered Wood I-Joists (TJIs)
Engineered I-joists consist of top and bottom solid wood or LVL flanges bonded to an oriented strand board (OSB) vertical web.
FLANGE RULE : NEVER cut, notch, or drill the top or bottom flanges of an I-joist under any circumstances. The flanges carry virtually all bending tension and compression.
WEB OPENINGS : Holes may be cut in the OSB web only in strict accordance with the manufacturer's printed web hole tables (which define hole diameter based on joist depth, span, and distance from bearing supports). Most I-joists feature pre-scored 1 1 2 ′ ′ 1\frac{1}{2}'' 1 2 1 ′′ round knockouts in the web for wiring and piping.
3. Wall Stud Drilling and Notching Rules (IRC Section R602.6)
Framing Member Type Maximum Bored Hole Diameter Maximum Notch Depth Code Conditions & Reinforcement
Exterior & Load-Bearing Stud 40% of stud width 25% of stud width Hole diameter can increase to 60% if the stud is doubled, or if an approved structural steel stud shoe is installed.
Non-Bearing Partition Stud 60% of stud width 40% of stud width No stud doubling required; hole edges must maintain at least 5/8" from face.
For a standard 2 × 4 2\times4 2 × 4 exterior load-bearing stud (actual width 3.5 ′ ′ 3.5'' 3. 5 ′′ ): Max Hole Diameter (Single Stud) = 3.5 ′ ′ × 0.40 = 1.40 inches \text{Max Hole Diameter (Single Stud)} = 3.5'' \times 0.40 = 1.40\text{ inches} Max Hole Diameter (Single Stud) = 3. 5 ′′ × 0.40 = 1.40 inches Max Hole Diameter (with Stud Shoe) = 3.5 ′ ′ × 0.60 = 2.10 inches \text{Max Hole Diameter (with Stud Shoe)} = 3.5'' \times 0.60 = 2.10\text{ inches} Max Hole Diameter (with Stud Shoe) = 3. 5 ′′ × 0.60 = 2.10 inches
Steel Protection Plates (Nail Plates) : If the edge of a bored hole or notch carrying piping, wiring, or tubing is closer than 1 1 4 inches 1\frac{1}{4}\text{ inches} 1 4 1 inches from the nearest face of the stud, a hardened steel nail protection plate (minimum 1 / 16 ′ ′ 1/16'' 1/1 6 ′′ thick, 16-gauge) must be installed over the face of the framing member to prevent drywall screws or siding nails from puncturing the pipe.
Equipment Clearances and Attic Access Requirements
Installing air handlers, furnaces, and packaged equipment in attics, crawl spaces, or mechanical closets is heavily regulated by the International Mechanical Code (IMC Section 306) and International Residential Code (IRC Section M1305) to ensure equipment can be safely serviced, inspected, and replaced. Attic Equipment Workspace & Access Layout:
- +-------------------------------------------------------------------------+
- | ROOF RAFTERS |
- | |
- | +-------------------+ [ 30" x 30" Level Working Platform ] |
- | | HVAC AIR HANDLER | Located on the service control side of unit |
- | +-------------------+ |
- | ^ |
- | | |
- | [ Solid Continuous Walkway: 24" Min Width ] |
- | Floor boards nailed solid to joists; max length 20 ft |
- | ^ |
- | | |
- | [ Attic Access Opening: 22" x 30" Minimum ] |
- | Light switch located at opening; 120V outlet near equipment |
- +-------------------------------------------------------------------------+
Code Mandates for Attic Installations:
Access Opening Dimensions : The attic access opening must be a minimum of 22 inches by 30 inches 22\text{ inches by } 30\text{ inches} 22 inches by 30 inches ( 559 mm × 762 mm 559\text{ mm} \times 762\text{ mm} 559 mm × 762 mm ). Furthermore, the opening must be large enough to allow the removal of the largest single equipment component (e.g., blower assembly, heat exchanger, or evaporator coil) without dismantling permanent building framing.
Passageway and Continuous Walkway : A continuous, solid unobstructed walkway (minimum 24 inches wide 24\text{ inches wide} 24 inches wide , constructed of solid boards or plywood subfloor secured to ceiling joists) must extend from the access opening directly to the equipment.
Maximum Walkway Length : The walkway length cannot exceed 20 feet 20\text{ feet} 20 feet ( 6 , 096 mm 6,096\text{ mm} 6 , 096 mm ). However, code permits the walkway to extend up to 50 feet 50\text{ feet} 50 feet if the clear vertical headroom height along the entire path is at least 6 feet 6\text{ feet} 6 feet ( 1 , 829 mm 1,829\text{ mm} 1 , 829 mm ) tall.
Service Workspace Platform : A level, solid working platform measuring at least 30 inches deep by 30 inches wide 30\text{ inches deep by } 30\text{ inches wide} 30 inches deep by 30 inches wide ( 762 mm × 762 mm 762\text{ mm} \times 762\text{ mm} 762 mm × 762 mm ) must be provided on the service and control access side of the equipment.
Electrical Lighting and Receptacle Requirements : A permanent electric luminaire (light fixture) controlled by a light switch located immediately at the attic access opening must illuminate the walkway and equipment. In addition, an independent 120 V 120\text{V} 120 V grounded convenience receptacle must be installed adjacent to the equipment for servicing power tools, vacuum pumps, and recovery units.