Study guide

12.2 AC Power, Magnetism & Control Transformers

NATE Core Knowledge Exam Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Introduction & Exam Overview

1.1 About the NATE Core Knowledge Exam 1.2 Study Strategy & Blueprint Navigation 1.3 HVAC Fundamentals & Math Review

2 Chapter 2: Safety Regulations & Jobsite Practices

2.1 Government & Environmental Regulations 2.2 Personal Safety, PPE & Jobsite Practices 2.3 Moving Machinery & Rotating Equipment Safety

3 Chapter 3: Hazardous Materials, Cylinders & Brazing Safety

3.1 Confined Spaces & Refrigerant Exposure Safety 3.2 Safe Brazing, Soldering & Nitrogen Purging 3.3 Compressed Gas Cylinders, Hazmat & Fire Safety

4 Chapter 4: Hand, Power & Fabrication Tools

4.1 Measurement & Layout Tools 4.2 Fastening & Mechanical Hand Tools 4.3 Sheet Metal Fabrication & Cutting Tools

5 Chapter 5: Copper Tubing Tools & Piping Practices

5.1 Copper Tubing Cutting & Reaming 5.2 Flaring Tools & Mechanical Joints 5.3 Swaging & Tubing Bending

6 Chapter 6: Basic Construction & Building Systems

6.1 Architectural Plans, Specifications & Blueprints 6.2 Structural Framing, Trusses & Clearances 6.3 Building Envelope & Fenestration 6.4 Mechanical Routing, Firestopping & Venting

7 Chapter 7: Basic Science & Thermodynamics

7.1 Matter, Chemistry & Combustion Principles 7.2 Pressure Fundamentals & Gas Laws 7.3 Applied HVAC Physics & Mathematics

8 Chapter 8: Achieving Desired Conditions & Comfort

8.1 Human Thermal Comfort & ASHRAE Standard 55 8.2 Humidity Control & System Psychrometrics 8.3 Ventilation Standards & ASHRAE Standard 62.2

9 Chapter 9: Indoor Air Quality & Acoustic Control

9.1 Air Filtration & MERV Ratings 9.2 Air Cleaning, Odor Control & UVGI 9.3 Sound & Vibration Attenuation

10 Chapter 10: Temperature & Heat Science

10.1 Sensible Heat, Latent Heat & BTU Fundamentals 10.2 Methods of Heat Transfer 10.3 Temperature Measurement Instruments & Calibration

11 Chapter 11: Humidity Measurements & Psychrometrics

11.1 Dry-Bulb, Wet-Bulb & Temperature Splits 11.2 Sling Psychrometers & Humidity Instruments 11.3 Psychrometric Chart Analysis & Enthalpy

12 Chapter 12: Electrical Fundamentals & Schematics

12.1 Electrical Concepts, Ohm's Law & Power 12.2 AC Power, Magnetism & Control Transformers 12.3 Electrical Loads & Power Factor 12.4 Electrical Symbols & Ladder Diagrams

13 Chapter 13: Electric Motors & Field Controls

13.1 Single-Phase Electric Motors & Capacitors 13.2 Three-Phase Motors & Commercial Power 13.3 Variable-Speed ECM Motors & Actuators 13.4 Field Wiring, Contactors & Control Devices

14 Chapter 14: Digital Meters & Electrical Diagnostics

14.1 Digital Multimeters & Safety Ratings 14.2 Voltage Drop, Amperage & Resistance Testing 14.3 Specialized Electrical Diagnostics: Megohmmeter, Capacitance & Micro-Signals

12.2 AC Power, Magnetism & Control Transformers

Key Takeaways Explain This Topic AI

Alternating Current (AC) reverses direction cyclically at 60 Hz in North America; standard digital multimeters measure Root-Mean-Square (RMS) effective voltage (VRMS = 0.707 * Vpeak), meaning nominal 120 VAC line voltage actually reaches alternating peaks of +/-169.7 V.

Electromagnetism operates all HVAC relays, contactors, and solenoids: electric current through a coiled conductor creates a concentrated magnetic field in an iron core, pulling an armature against spring tension; shading coils prevent 60 Hz mechanical chatter.

HVAC control transformers operate on mutual electromagnetic induction, stepping down line voltage (120V, 208V, 240V, or 480V) to 24 VAC Class 2 control voltage based on the turns ratio formula: Vp / Vs = Np / Ns = Is / Ip.

Multi-tap transformer primary leads must be connected strictly to the tap matching incoming line voltage (e.g., using the 208V tap on 208V network supplies); connecting 208V to a 240V tap results in an under-voltage of 20.8 VAC on the secondary, causing contactor chattering and coil burnout.

Transformer capacity is rated in Volt-Amperes (VA = V * I); 40 VA transformers support a maximum secondary current of 1.67 A, and must be protected by a 3A or 5A automotive blade fuse or resettable circuit breaker against low-voltage wiring shorts.

Last updated: September 2026

  • 12.2 AC Power, Magnetism & Control Transformers
  • Alternating Current (AC) vs. Direct Current (DC) Fundamentals

Electrical power in HVAC/R systems is classified into two distinct operational formats: Direct Current (DC) and Alternating Current (AC).

Direct Current (DC) Dynamics in HVAC Controls

In Direct Current (DC) circuits, electrons flow continuously in a single direction from the negative terminal toward the positive terminal. The voltage potential remains constant over time.

Primary HVAC DC Sources : Chemical storage batteries (multimeter batteries, emergency generator starter batteries, wireless thermostat cells), photovoltaic solar arrays, and electronic power supply rectifiers on control boards.

Electronic Microprocessor Control : Microprocessor logic boards convert incoming AC voltage into regulated 5 VDC 5\text{ VDC} 5 VDC , 12 VDC 12\text{ VDC} 12 VDC , or 24 VDC 24\text{ VDC} 24 VDC to operate microcontrollers, logic gates, and sensor inputs.

Flame Rectification : Modern furnace ignition modules pass an AC voltage through a flame sensor rod into a burner flame; the flame acts as a natural electrical diode, rectifying the AC voltage into a tiny pulsating Direct Current ( 0.5 to 5.0 μ A DC 0.5\text{ to }5.0\text{ }\mu\text{A DC} 0.5 to 5.0 μ A DC ) that proves flame presence to the safety circuit.

Alternating Current (AC) Principles & Frequency

In Alternating Current (AC) circuits, electrons do not travel continuously through the wire. Instead, they oscillate back and forth in place, periodically reversing direction at regular intervals. AC power is generated commercially by rotating electromagnetic coils within stationary magnetic fields at central utility power plants.

Frequency ( f f f ) : The number of complete cycles executed per second, measured in Hertz (Hz) ( 1 Hz = 1 cycle per second 1\text{ Hz} = 1\text{ cycle per second} 1 Hz = 1 cycle per second ).

Standard North American Frequency : In North America, commercial utility power operates at standard 60 Hz 60\text{ Hz} 60 Hz (in Europe and Asia, 50 Hz 50\text{ Hz} 50 Hz is standard).

Period ( T T T ) : The elapsed time required to complete one single cycle, calculated as the inverse of frequency: T = 1 f = 1 60 Hz ≈ 0.01667 seconds ( 16.67 milliseconds ) T = \frac{1}{f} = \frac{1}{60\text{ Hz}} \approx 0.01667\text{ seconds } (16.67\text{ milliseconds}) T = f 1 ​ = 60 Hz 1 ​ ≈ 0.01667 seconds ( 16.67 milliseconds ) AC Sine Wave Voltage Geometry (60 Hz):

  • =========================================================================
  • +V_peak (+170V) ------> /\ [ Peak-to-Peak ]
  • / \ [ Voltage ]
  • / \ [ (340V) ]
  • 0V Baseline ----------->+------+------+--->
  • \ /
  • \ /
  • V_peak (-170V) ----------------> \/
  • <--- 1 Cycle (16.67 ms) --->
  • =========================================================================
  • Sine Wave Geometry: Peak, Peak-to-Peak, and Root-Mean-Square (RMS)

Because an AC voltage wave continuously changes value—starting at zero, climbing to a positive maximum, falling through zero, descending to a negative maximum, and returning to zero—technicians must understand three distinct voltage measurement conventions:

Peak Voltage ( V peak V_{\text{peak}} V peak ​ ) : The maximum instantaneous voltage reached in either direction during an alternation ( 90 ∘ 90^\circ 9 0 ∘ positive peak and 270 ∘ 270^\circ 27 0 ∘ negative peak).

Peak-to-Peak Voltage ( V p-p V_{\text{p-p}} V p-p ​ ) : The total electrical distance from the absolute crest of the positive peak to the absolute trough of the negative peak: V p-p = 2 × V peak V_{\text{p-p}} = 2 \times V_{\text{peak}} V p-p ​ = 2 × V peak ​

Root-Mean-Square (RMS) / Effective Voltage ( V RMS V_{\text{RMS}} V RMS ​ ) : The effective value of an alternating current wave, representing the equivalent DC voltage that would produce the exact same heating effect (Joule heating) in an identical resistive load.

Technicians must master the standard conversion formulas between Peak and RMS: V RMS = V peak × 0.707 = V peak 2 V_{\text{RMS}} = V_{\text{peak}} \times 0.707 = \frac{V_{\text{peak}}}{\sqrt{2}} V RMS ​ = V peak ​ × 0.707 = 2 ​ V peak ​ ​ V peak = V RMS 0.707 = V RMS × 1.414 V_{\text{peak}} = \frac{V_{\text{RMS}}}{0.707} = V_{\text{RMS}} \times 1.414 V peak ​ = 0.707 V RMS ​ ​ = V RMS ​ × 1.414

Nominal RMS Voltage ( V RMS V_{\text{RMS}} V RMS ​ ) Peak Voltage ( V peak V_{\text{peak}} V peak ​ ) Peak-to-Peak Voltage ( V p-p V_{\text{p-p}} V p-p ​ ) Common HVAC Application

24 VAC 24\text{ VAC} 24 VAC 33.9 V 33.9\text{ V} 33.9 V 67.9 V 67.9\text{ V} 67.9 V Low-voltage control circuits, thermostats, contactor coils.

120 VAC 120\text{ VAC} 120 VAC 169.7 V ≈ 170 V 169.7\text{ V} \approx 170\text{ V} 169.7 V ≈ 170 V 339.4 V ≈ 340 V 339.4\text{ V} \approx 340\text{ V} 339.4 V ≈ 340 V Residential furnace power, inducer motors, condensate pumps.

208 VAC 208\text{ VAC} 208 VAC 294.1 V 294.1\text{ V} 294.1 V 588.2 V 588.2\text{ V} 588.2 V Commercial 3-phase wye networks (light commercial package units).

240 VAC 240\text{ VAC} 240 VAC 339.4 V ≈ 340 V 339.4\text{ V} \approx 340\text{ V} 339.4 V ≈ 340 V 678.8 V ≈ 680 V 678.8\text{ V} \approx 680\text{ V} 678.8 V ≈ 680 V Residential condensing units, heat pump compressors, electric duct heaters.

480 VAC 480\text{ VAC} 480 VAC 678.8 V 678.8\text{ V} 678.8 V 1 , 357.6 V 1,357.6\text{ V} 1 , 357.6 V Heavy commercial chillers, rooftop units, industrial cooling towers.

Important

Why Digital Multimeters Read RMS : Unless explicitly configured to display peak hold, all standard digital multimeters (DMMs) are calibrated to display V RMS V_{\text{RMS}} V RMS ​ . When a technician measures 120 VAC 120\text{ VAC} 120 VAC at a convenience outlet or furnace terminal, the meter indicates an effective RMS value; the actual voltage on that circuit is oscillating between + 170 V +170\text{ V} + 170 V and − 170 V -170\text{ V} − 170 V sixty times each second.

Magnetism and Electromagnetism in HVAC Equipment

Magnetism and electricity are inseparable manifestations of the fundamental electromagnetic force. Electromagnetism is the mechanical engine behind HVAC relays, contactors, solenoid valves, and electric motors.

Magnetic Fields and Magnetic Flux

A magnet is surrounded by invisible lines of force called magnetic flux . Magnetic lines of flux possess distinct properties:

They exit the North pole of a magnet, travel through the surrounding medium, and enter the South pole, forming complete continuous closed loops.

Magnetic flux lines repel each other and never cross or intersect.

Materials with high magnetic permeability (such as soft iron or silicon steel) allow magnetic flux lines to pass through them with minimal opposition ( reluctance ), concentrating the magnetic field.

Electromagnetism and Solenoid Action

When an electric current flows through a straight conductor, a circular magnetic field is generated concentrically around the wire. If the wire is coiled into a helical cylinder (forming a solenoid coil ), the magnetic fields of individual wire turns combine, creating a powerful, concentrated magnetic field identical to that of a permanent bar magnet, with distinct North and South poles.

By inserting a soft iron core into the center of the coil, the magnetic field strength multiplies thousands of times. When current is removed, the soft iron core loses virtually all its magnetism immediately (low retentivity ), allowing mechanical components to return instantly to their rest positions via spring tension. Electromagnetic Contactor Mechanical Operation:

  • =========================================================================
  • [ De-Energized State ] [ Energized State (24 VAC Applied) ]
  • Stationary Contacts (Open) Stationary Contacts (Closed)
  • | | | | | | | |
  • o o o o o=o o=o <-- Power Flow
  • ^ ^ ^ ^
  • [ Mobile Contact Bar ] [ Mobile Contact Bar Pulled Down ]
  • | |
  • [ Spring ] (Pushes UP) [ Spring ] (Compressed)
  • | |
  • [ Iron Armature ] [ Iron Armature Pulled Down ]
  • | |
  • (Air Gap) (Core Contact - Gap Closed)
  • | |
  • [ 24V Solenoid Coil ] [ 24V Solenoid Coil ENERGIZED ]
  • [ Laminated Core ] [ Laminated Core Magnetic Field ]
  • =========================================================================
  • Contactors, Relays, and Shading Coils

Contactor / Relay Mechanics : A contactor consists of a stationary laminated iron core surrounded by an electromagnetic coil, a movable iron armature attached to electrical contact points, and mechanical return springs. When the coil is energized with control voltage ( 24 VAC 24\text{ VAC} 24 VAC ), the resulting magnetic flux overcomes the spring tension, pulling the armature down and slamming the electrical contacts shut to energize heavy loads.

The Shading Coil : Because alternating current drops to zero voltage twice every cycle ( 120 times per second 120\text{ times per second} 120 times per second in a 60 Hz 60\text{ Hz} 60 Hz system), the magnetic pull of the coil drops to zero 120 times per second 120\text{ times per second} 120 times per second . Without counter-measures, the return springs would pull the contacts partially open during every zero-crossing, causing violent mechanical buzzing, electrical arcing, contact chatter, and rapid failure.

To prevent this, manufacturers embed a shading coil —a heavy, closed copper ring—around a fraction of the stationary pole face. The main alternating magnetic field induces an out-of-phase secondary current and magnetic field in this copper loop. When the primary magnetic field passes through zero, the out-of-phase secondary field maintains magnetic attraction, holding the armature firmly sealed and completely silent.

Control Transformers and Mutual Electromagnetic Induction

A transformer is a static electromagnetic device that transfers electrical energy from one circuit to another through mutual induction without any direct physical electrical connection between the two circuits.

Operating Principle: Mutual Induction

Alternating current from the primary line power supply flows through the primary winding .

This alternating current generates a constantly expanding, collapsing, and reversing magnetic flux within the laminated silicon-steel transformer core.

The alternating magnetic flux travels through the closed core loop and cuts across the turns of the secondary winding .

By Faraday's Law of Electromagnetic Induction, the moving magnetic flux induces an alternating electromotive force (voltage) across the secondary winding terminals. Mutual Induction Across Transformer Core:

  • =========================================================================
  • Primary Winding Laminated Iron Core Secondary Winding
  • (Line Voltage AC) (Magnetic Flux Path) (Control Voltage AC)
  • +---( ~ )---+ +====+ +---( Load )---+
  • | ) | | || | | ) |
  • | ) | | || | | ) |
  • | Np Turns| ~~~ Magnetic Flux ~~~> | || | ~~~> | Ns Turns |
  • | ) | | || | | ) |
  • | ) | | || | | ) |
  • +-----------+ +====+ +--------------+
  • =========================================================================
  • The Transformer Turns Ratio Formula

The ratio of primary voltage to secondary voltage is directly proportional to the ratio of primary winding turns to secondary winding turns, and inversely proportional to the ratio of primary to secondary current: V p V s = N p N s = I s I p \frac{V_p}{V_s} = \frac{N_p}{N_s} = \frac{I_s}{I_p} V s ​ V p ​ ​ = N s ​ N p ​ ​ = I p ​ I s ​ ​

Where:

  • V p V_p V p ​ = Primary line voltage (Volts)
  • V s V_s V s ​ = Secondary output voltage (Volts)
  • N p N_p N p ​ = Number of wire turns on the primary winding
  • N s N_s N s ​ = Number of wire turns on the secondary winding
  • I p I_p I p ​ = Primary line current (Amps)
  • I s I_s I s ​ = Secondary output current (Amps)

In HVAC systems, almost all control transformers are step-down transformers ( V p > V s V_p > V_s V p ​ > V s ​ ), meaning the primary winding has many turns of fine wire while the secondary winding has fewer turns of heavier wire ( N p > N s N_p > N_s N p ​ > N s ​ ).

Worked Example: Turns Ratio Calculation

A step-down transformer has a primary winding containing 1 , 200 turns 1,200\text{ turns} 1 , 200 turns connected to a 240 VAC 240\text{ VAC} 240 VAC line. The secondary winding delivers 24 VAC 24\text{ VAC} 24 VAC .

Calculate the turns ratio: Ratio = V p V s = 240 V 24 V = 10 : 1 \text{Ratio} = \frac{V_p}{V_s} = \frac{240\text{ V}}{24\text{ V}} = 10:1 Ratio = V s ​ V p ​ ​ = 24 V 240 V ​ = 10 : 1

Calculate the number of secondary turns ( N s N_s N s ​ ): N s = N p Ratio = 1 , 200 10 = 120 turns N_s = \frac{N_p}{\text{Ratio}} = \frac{1,200}{10} = 120\text{ turns} N s ​ = Ratio N p ​ ​ = 10 1 , 200 ​ = 120 turns

Class 2 Low-Voltage Power Supplies in HVAC/R

The National Electrical Code (NEC) designates standard 24 VAC 24\text{ VAC} 24 VAC HVAC control circuits as Class 2 Power-Limited Circuits . Class 2 circuits operate at low voltage ( < 30 VAC <30\text{ VAC} < 30 VAC ) and limit total power output to a maximum of 100 VA 100\text{ VA} 100 VA . This power limitation significantly reduces electric shock hazard and minimizes the risk of electrical fire from short circuits, permitting technicians to utilize lighter-gauge thermostat cables (#18 AWG) without running them inside rigid metal conduit.

Multi-Tap Primary Transformer Connections & Field Hazards

Commercial and residential replacement transformers are commonly designed with multi-tap primaries to accommodate various field supply voltages on a single stock component. A universal replacement transformer typically includes primary leads labeled:

  • Common (White)
  • 120 VAC 120\text{ VAC} 120 VAC Tap (Black)
  • 208 VAC 208\text{ VAC} 208 VAC Tap (Red)
  • 240 VAC 240\text{ VAC} 240 VAC Tap (Orange or Blue)

Technicians must cap off all unused primary leads individually with wire nuts and tape; an unused primary lead will develop an induced voltage when the transformer is energized and can shock a technician or short to the cabinet frame. Multi-Tap Primary Transformer Wiring Diagram:

  • +---[ Line Hot Conductor ]-----------------------------------------------+
  • | |
  • | +---[ 120V Tap (Black) ] -------- (Capped with wire nut if not used) |
  • | +---[ 208V Tap (Red) ] ---------- (Connected if 208V 3-Phase Supply) |
  • | +---[ 240V Tap (Orange) ] ------- (Connected if 240V 1-Phase Supply) |
  • | |
  • | [ Primary Coils on Core ] |
  • | |
  • +---[ Line Common / Neutral (White) ]------------------------------------+
  • +---[ Secondary R Terminal (24 VAC Hot) ]---> [ 3A Fuse ] ---> Thermostat
  • +---[ Secondary C Terminal (24 VAC Common) ]-----------------> Contactor Ground
  • The Danger of Primary Tap Mismatch (208V vs. 240V)

A frequent, severe field installation error occurs in commercial buildings served by a 208 VAC 208\text{ VAC} 208 VAC three-phase wye distribution system. If an installer carelessly connects the incoming 208 V 208\text{ V} 208 V line to the transformer's 240 V 240\text{ V} 240 V primary tap:

The transformer is internally configured for a 10 : 1 10:1 10 : 1 step-down turns ratio ( 240 V / 24 V = 10 240\text{ V} / 24\text{ V} = 10 240 V /24 V = 10 ).

With only 208 VAC 208\text{ VAC} 208 VAC applied across this 240 V 240\text{ V} 240 V winding, the resulting secondary voltage drops to: V s = 208 V 10 = 20.8 VAC V_s = \frac{208\text{ V}}{10} = 20.8\text{ VAC} V s ​ = 10 208 V ​ = 20.8 VAC

Consequences of Low Control Voltage ( 20.8 VAC 20.8\text{ VAC} 20.8 VAC ) : Contactor coils lack sufficient electromagnetic pull to clamp down firmly against return spring pressure. The contactor vibrates and chatters violently, drawing high inductive current, destroying the contact points through electrical arcing, and burning out the contactor coil within days. Electronic control boards may also experience intermittent microprocessor resets.

Conversely, connecting a 240 VAC 240\text{ VAC} 240 VAC supply to a 208 V 208\text{ V} 208 V tap produces 27.7 VAC 27.7\text{ VAC} 27.7 VAC on the secondary, which can overheat coils and over-voltage sensitive solid-state circuit boards.

Transformer Volt-Ampere (VA) Capacity & Secondary Circuit Protection

Control transformers are rated by their apparent power capacity in Volt-Amperes (VA) , which represents the product of secondary voltage and secondary maximum allowable current: VA = V s × I s \text{VA} = V_s \times I_s VA = V s ​ × I s ​

Calculating Maximum Secondary Current

Technicians must calculate the maximum continuous secondary current a transformer can support without overheating: I max = VA Rating V s = VA Rating 24 V I_{\text{max}} = \frac{\text{VA Rating}}{V_s} = \frac{\text{VA Rating}}{24\text{ V}} I max ​ = V s ​ VA Rating ​ = 24 V VA Rating ​

Transformer VA Rating Nominal Secondary Voltage Maximum Secondary Current ( I max I_{\text{max}} I max ​ ) Typical Equipment Application

40 VA 40\text{ VA} 40 VA 24 VAC 24\text{ VAC} 24 VAC 40 / 24 = 1.67 A 40 / 24 = 1.67\text{ A} 40/24 = 1.67 A Basic residential split systems (single contactor + indoor fan relay).

50 VA 50\text{ VA} 50 VA 24 VAC 24\text{ VAC} 24 VAC 50 / 24 = 2.08 A 50 / 24 = 2.08\text{ A} 50/24 = 2.08 A Residential systems with smart thermostats and electronic air cleaners.

75 VA 75\text{ VA} 75 VA 24 VAC 24\text{ VAC} 24 VAC 75 / 24 = 3.125 A 75 / 24 = 3.125\text{ A} 75/24 = 3.125 A Multi-zone motorized damper systems or two-stage heat pumps.

100 VA 100\text{ VA} 100 VA 24 VAC 24\text{ VAC} 24 VAC 100 / 24 = 4.17 A 100 / 24 = 4.17\text{ A} 100/24 = 4.17 A Light commercial rooftop units with economizers and multiple stages.

Field Overloading from Control Accessories

A standard residential 40 VA 40\text{ VA} 40 VA transformer is sized at the factory to handle basic equipment loads (e.g., outdoor contactor pulling 0.55 A 0.55\text{ A} 0.55 A plus indoor fan relay pulling 0.30 A 0.30\text{ A} 0.30 A , total 0.85 A < 1.67 A 0.85\text{ A} < 1.67\text{ A} 0.85 A < 1.67 A ). When homeowners add aftermarket accessories—such as power-stealing Wi-Fi smart thermostats ( 0.25 A 0.25\text{ A} 0.25 A ), motorized zoning dampers ( 0.45 A 0.45\text{ A} 0.45 A each), electronic bypass humidifiers ( 0.35 A 0.35\text{ A} 0.35 A ), and UV lamps—the total current can exceed 1.67 A 1.67\text{ A} 1.67 A . The transformer core overheats, winding varnish breaks down, and the secondary winding burns open.

Secondary Fusing and Short-Circuit Diagnostics

To protect transformers from burning out during control wiring shorts (such as a pinched thermostat wire, a grounded contactor coil, or a rodent-chewed cable), technicians must install overcurrent protection in series with the secondary 24 V 24\text{ V} 24 V Hot (R) terminal:

Automotive Blade Fuse : A standard 3 A 3\text{ A} 3 A or 5 A 5\text{ A} 5 A fast-acting blade fuse (ATC or ATO) mounted in an inline fuse holder.

Resettable Push-Button Breaker : A 3 A 3\text{ A} 3 A thermal circuit breaker mounted on the air handler control panel.

Warning

Never Replace a 3A Fuse with a 5A Fuse on a 40 VA Transformer : A 40 VA 40\text{ VA} 40 VA transformer has an absolute thermal limit of 1.67 A 1.67\text{ A} 1.67 A . Installing a 5 A 5\text{ A} 5 A fuse allows the control circuit to draw up to 5.0 A 5.0\text{ A} 5.0 A continuously under partial short conditions, destroying the transformer windings before the fuse can clear.