Study guide

3.2 Psychrometric Chart Fundamentals: Dry-Bulb, Wet-Bulb, Dew Point & Humidity

NATE HVAC Certification Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

0.1 NATE Certification Pathways: CHP-5 vs. Traditional Core & Specialty 0.2 Exam Logistics, Scoring, EPA 608 Prerequisites & Recertification 0.3 Effective Study Strategies & Recommended Field Test Preparation

2 Chapter 1: HVAC Fundamentals & Safety

1.1 Personal & Job-Site Safety, PPE, Lockout/Tagout, and OSHA Compliance 1.2 Specialized HVAC Hand Tools, Vacuum Pumps, Manifold Gauges, and Meters 1.3 Principles of Heat Transfer, Temperature Scales, and Heat Quantity Calculations 1.4 The Vapor Compression Refrigeration Cycle & Component Roles 1.5 Refrigerant Classifications, Recovery/Recycling, and EPA Section 608 Laws

3 Chapter 2: Electrical Theory, Controls & Troubleshooting

2.1 Electrical Fundamentals, Ohm's Law, and Circuit Configurations 2.2 Electric Motors, Capacitors, Relays, Contactors, and Starters 2.3 Low-Voltage Controls, Thermostats, Transformers, and Safety Switches 2.4 Reading HVAC Schematics, Ladder Diagrams, and Wiring Diagrams 2.5 Systematic Electrical Troubleshooting & Multimeter Diagnostics

4 Chapter 3: Comfort, Airflow & Psychrometrics

3.1 Fundamentals of Indoor Air Quality (IAQ) and Human Comfort Parameters 3.2 Psychrometric Chart Fundamentals: Dry-Bulb, Wet-Bulb, Dew Point & Humidity 3.3 Airflow Dynamics, Duct Static Pressure, Velocity, and CFM Calculations 3.4 Ductwork Design, Blower Performance Curves, and Air Balancing 3.5 Ventilation Standards, Filtration Ratings (MERV), and Humidity Control

5 Chapter 4: Equipment Installation & Commissioning

4.1 Equipment Placement, Clearances, Mounting, and Code Compliance 4.2 Refrigerant Piping, Copper Tubing Prep, Nitrogen Purge, and Brazing 4.3 Deep Vacuum Evacuation, Micron Gauges, and System Dehydration 4.4 Refrigerant Charging Methods: Superheat, Subcooling, and Weigh-In 4.5 System Commissioning, Startup Checks, and Combustion Analysis

6 Chapter 5: Service, Diagnostics & Preventive Maintenance

5.1 Systematic Troubleshooting Workflow & Problem Identification 5.2 Compressor Diagnostics, Mechanical Failures, and Electrical Faults 5.3 Air Conditioning & Heat Pump Service: Reversing Valves, Defrost & Metering Devices 5.4 Gas & Electric Heating Service: Ignition Controls, Heat Exchangers & Flame Sensors 5.5 Preventive Maintenance Protocols, Seasonal Tune-Ups, and Customer Service

3.2 Psychrometric Chart Fundamentals: Dry-Bulb, Wet-Bulb, Dew Point & Humidity

Key Takeaways Explain This Topic AI

Psychrometrics is the thermodynamic study of moist air properties at a given barometric pressure, typically 14.696 psia (29.92 in. Hg) at sea level.

The seven core air properties on a psychrometric chart are dry-bulb, wet-bulb, dew point, relative humidity, specific humidity (grains/lb), specific volume (cu ft/lb), and enthalpy (BTU/lb).

At 100% relative humidity (the saturation curve), dry-bulb, wet-bulb, and dew point temperatures are all exactly equal.

Total heat removal by an air conditioner is calculated using enthalpy change: Q_total = 4.5 × CFM × Δh.

One pound of liquid water contains exactly 7,000 grains of moisture, the baseline unit for humidity ratio calculations.

Last updated: July 2026

Psychrometric Chart Fundamentals: Dry-Bulb, Wet-Bulb, Dew Point & Humidity

Psychrometrics is the thermodynamic study of the physical, thermal, and vapor properties of moist air (air-and-water vapor mixtures). In HVAC engineering and field diagnostics, the psychrometric chart serves as the fundamental graphical tool for plotting thermodynamic state points, evaluating coil performance, calculating sensible and latent cooling capacities, and diagnosing airflow and moisture issues. Standard sea-level psychrometric charts are constructed for a barometric pressure of 14.696 psia (29.92 inches of Mercury / 101.325 kPa).

The Seven Core Thermodynamic Air Properties

If any two independent thermodynamic air properties are known, the state point of the air can be pinpointed on the psychrometric chart, revealing the remaining five properties. The seven core properties plotted on the chart are:

Dry-Bulb Temperature (DB): Ambient air temperature measured by a standard dry thermometer uninfluenced by moisture or radiant heat. Displayed along the horizontal baseline axis as straight vertical lines (°F).

Wet-Bulb Temperature (WB): Temperature measured by a thermometer covered with a distilled water-wetted sock exposed to rapid airflow (approx. 1,000 FPM). It reflects evaporative cooling capacity. Displayed as diagonal lines slanting downward from top-left to bottom-right (°F).

Dew Point Temperature (DP): Temperature at which air reaches 100% saturation and moisture condenses from water vapor into liquid water during cooling at constant pressure. Displayed as horizontal lines extending to the right vertical axis or curved saturation line (°F).

Relative Humidity (RH): Ratio of actual water vapor pressure present in the air to maximum saturated water vapor pressure possible at that dry-bulb temperature, expressed as a percentage. Represented by curved lines rising from lower-left to upper-right (0% to 100% saturation curve).

Specific Humidity / Humidity Ratio (W): Actual mass weight of moisture contained per pound of dry air. Expressed in pounds of water per pound of dry air ( l b H 2 O / l b a i r lb\ H_2O / lb\ air l b H 2 ​ O / l b ai r ) or in grains of moisture per pound of dry air . There are 7,000 grains in one pound of liquid water . Humidity ratio is plotted on the right vertical axis.

Specific Volume (v): Volume occupied by one pound of dry air plus its associated water vapor, measured in cubic feet per pound of dry air ( c u f t / l b cu\ ft/lb c u f t / l b ). Represented by steep diagonal lines. Standard sea-level dry air at 70°F has a specific volume of 13.33 to 13.50 c u f t / l b 13.33\ \text{to}\ 13.50\ cu\ ft/lb 13.33 to 13.50 c u f t / l b , yielding a standard air density of 0.075 lb/cu ft .

Enthalpy (h): Total heat content of the air-water mixture above a 0°F reference datum, measured in BTU per pound of dry air ( B T U / l b BTU/lb BT U / l b ). Plotted on an outer scale along extended diagonal wet-bulb lines.

The Saturation Line Rule

On the curved boundary of the psychrometric chart—known as the 100% Relative Humidity line or Saturation Curve —air is holding its maximum capacity of water vapor at that temperature. At saturation: Dry-Bulb Temperature = Wet-Bulb Temperature = Dew Point Temperature \text{Dry-Bulb Temperature} = \text{Wet-Bulb Temperature} = \text{Dew Point Temperature} Dry-Bulb Temperature = Wet-Bulb Temperature = Dew Point Temperature

When air is cooled below its dew point temperature, moisture condenses out of the airstream onto cold surfaces (such as an evaporator coil operating below the dew point of return air).

Psychrometric Processes and Vector Lines

Thermodynamic state changes across HVAC equipment appear as directional vectors on the psychrometric chart:

Sensible Heating: Horizontal movement to the right. Dry-bulb temperature increases, humidity ratio (grains) remains constant, dew point remains constant, and relative humidity decreases.

Sensible Cooling: Horizontal movement to the left. Dry-bulb temperature decreases, humidity ratio (grains) remains constant, dew point remains constant, and relative humidity increases toward saturation.

Cooling and Dehumidification (Standard DX Coil Operation): Diagonal vector slanting downward and to the left. Dry-bulb, wet-bulb, dew point, humidity ratio, and enthalpy all decrease simultaneously.

Heating and Humidification: Diagonal vector slanting upward and to the right.

Evaporative Cooling (Adiabatic Humidification): Downward movement along a constant wet-bulb / enthalpy line toward the saturation curve. Sensible heat converts into latent heat: dry-bulb drops, relative humidity rises, grains increase, but total enthalpy remains unchanged.

Governing Psychrometric Heat Equations

Technicians compute sensible, latent, and total cooling capacities using three fundamental mathematical formulas derived from standard air density ( 0.075 l b / c u f t 0.075\ lb/cu\ ft 0.075 l b / c u f t ) and minute-to-hour conversion ( 60 m i n / h r 60\ min/hr 60 min / h r ):

Sensible Heat Formula Q s e n s i b l e = 1.08 × C F M × Δ T Q_{sensible} = 1.08 \times CFM \times \Delta T Q se n s ib l e ​ = 1.08 × CFM × Δ T

Where 1.08 = 60 × 0.075 × 0.24 BTU/lb/ ∘ F 1.08 = 60 \times 0.075 \times 0.24\ \text{BTU/lb/}^\circ\text{F} 1.08 = 60 × 0.075 × 0.24 BTU/lb/ ∘ F (specific heat of air), and Δ T = D B r e t u r n − D B s u p p l y \Delta T = DB_{return} - DB_{supply} Δ T = D B re t u r n ​ − D B s u ppl y ​ .

Latent Heat Formula Q l a t e n t = 0.68 × C F M × Δ W Q_{latent} = 0.68 \times CFM \times \Delta W Q l a t e n t ​ = 0.68 × CFM × Δ W

Where 0.68 = 60 × 0.075 × 1061 7000 0.68 = \frac{60 \times 0.075 \times 1061}{7000} 0.68 = 7000 60 × 0.075 × 1061 ​ , and Δ W = W r e t u r n − W s u p p l y \Delta W = W_{return} - W_{supply} Δ W = W re t u r n ​ − W s u ppl y ​ in grains of moisture per pound of dry air .

Total Heat Formula Q t o t a l = 4.5 × C F M × Δ h Q_{total} = 4.5 \times CFM \times \Delta h Q t o t a l ​ = 4.5 × CFM × Δ h

Where 4.5 = 60 × 0.075 lb/cu ft 4.5 = 60 \times 0.075\ \text{lb/cu ft} 4.5 = 60 × 0.075 lb/cu ft , and Δ h = h r e t u r n − h s u p p l y \Delta h = h_{return} - h_{supply} Δ h = h re t u r n ​ − h s u ppl y ​ in BTU per pound of dry air .

  • Air Property Chart Line Orientation Standard Units Common Measurement Tool
  • Dry-Bulb (DB) Straight vertical lines Degrees Fahrenheit (°F) Standard dry thermometer / thermistor
  • Wet-Bulb (WB) Diagonal slanting lines Degrees Fahrenheit (°F) Sling psychrometer with wetted sock
  • Dew Point (DP) Horizontal straight lines Degrees Fahrenheit (°F) Chilled-mirror dew point sensor
  • Relative Humidity Curved lines (0% to 100%) Percentage (%) Digital capacitive hygrometer
  • Humidity Ratio Horizontal lines to right axis Grains / lb dry air Calculated from DB and WB

Specific Volume Steep diagonal lines c u f t / l b d r y a i r cu\ ft / lb\ dry\ air c u f t / l b d ry ai r Calculated / Psychrometric chart

Enthalpy Diagonal lines to outer scale B T U / l b d r y a i r BTU / lb\ dry\ air BT U / l b d ry ai r Calculated from WB line extension

Loading diagram... Psychrometric Process Directions and Vector Paths