Study guide
1.3 Principles of Heat Transfer, Temperature Scales, and Heat Quantity Calculations
NATE HVAC Certification Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
0.1 NATE Certification Pathways: CHP-5 vs. Traditional Core & Specialty 0.2 Exam Logistics, Scoring, EPA 608 Prerequisites & Recertification 0.3 Effective Study Strategies & Recommended Field Test Preparation
2 Chapter 1: HVAC Fundamentals & Safety
1.1 Personal & Job-Site Safety, PPE, Lockout/Tagout, and OSHA Compliance 1.2 Specialized HVAC Hand Tools, Vacuum Pumps, Manifold Gauges, and Meters 1.3 Principles of Heat Transfer, Temperature Scales, and Heat Quantity Calculations 1.4 The Vapor Compression Refrigeration Cycle & Component Roles 1.5 Refrigerant Classifications, Recovery/Recycling, and EPA Section 608 Laws
3 Chapter 2: Electrical Theory, Controls & Troubleshooting
2.1 Electrical Fundamentals, Ohm's Law, and Circuit Configurations 2.2 Electric Motors, Capacitors, Relays, Contactors, and Starters 2.3 Low-Voltage Controls, Thermostats, Transformers, and Safety Switches 2.4 Reading HVAC Schematics, Ladder Diagrams, and Wiring Diagrams 2.5 Systematic Electrical Troubleshooting & Multimeter Diagnostics
4 Chapter 3: Comfort, Airflow & Psychrometrics
3.1 Fundamentals of Indoor Air Quality (IAQ) and Human Comfort Parameters 3.2 Psychrometric Chart Fundamentals: Dry-Bulb, Wet-Bulb, Dew Point & Humidity 3.3 Airflow Dynamics, Duct Static Pressure, Velocity, and CFM Calculations 3.4 Ductwork Design, Blower Performance Curves, and Air Balancing 3.5 Ventilation Standards, Filtration Ratings (MERV), and Humidity Control
5 Chapter 4: Equipment Installation & Commissioning
4.1 Equipment Placement, Clearances, Mounting, and Code Compliance 4.2 Refrigerant Piping, Copper Tubing Prep, Nitrogen Purge, and Brazing 4.3 Deep Vacuum Evacuation, Micron Gauges, and System Dehydration 4.4 Refrigerant Charging Methods: Superheat, Subcooling, and Weigh-In 4.5 System Commissioning, Startup Checks, and Combustion Analysis
6 Chapter 5: Service, Diagnostics & Preventive Maintenance
5.1 Systematic Troubleshooting Workflow & Problem Identification 5.2 Compressor Diagnostics, Mechanical Failures, and Electrical Faults 5.3 Air Conditioning & Heat Pump Service: Reversing Valves, Defrost & Metering Devices 5.4 Gas & Electric Heating Service: Ignition Controls, Heat Exchangers & Flame Sensors 5.5 Preventive Maintenance Protocols, Seasonal Tune-Ups, and Customer Service
1.3 Principles of Heat Transfer, Temperature Scales, and Heat Quantity Calculations
Key Takeaways Explain This Topic AI
The Second Law of Thermodynamics dictates that heat energy always flows spontaneously from a region of higher temperature to a region of lower temperature.
Sensible heat causes a measurable change in temperature without changing the physical state of a substance, calculated as Q = m × c × Δ T Q = m \times c \times \Delta T Q = m × c × Δ T .
Latent heat causes a change in physical state (phase change) at a constant temperature and pressure, such as latent heat of vaporization (970.4 BTU/lb for water).
Sensible heat calculations for airflow utilize the formula Q sensible = 1.08 × CFM × Δ T Q_{\text{sensible}} = 1.08 \times \text{CFM} \times \Delta T Q sensible = 1.08 × CFM × Δ T , where 1.08 represents the air density-specific heat conversion factor.
One Ton of Refrigeration equals 12,000 BTU/hr (288,000 BTU/24 hr), defined as the heat absorption required to melt 2,000 lbs of ice at 32°F in 24 hours.
Last updated: July 2026
Principles of Heat Transfer, Temperature Scales, and Heat Quantity Calculations
Thermodynamics governs all heating, ventilation, air conditioning, and refrigeration processes. Air conditioning is not the addition of cold, but rather the removal of heat energy from a conditioned space and its rejection to an external sink.
Fundamental Laws of Thermodynamics
HVAC engineering rests upon two core thermodynamic principles:
First Law of Thermodynamics (Conservation of Energy): Energy cannot be created or destroyed, only converted from one form to another. In a refrigeration system, electrical energy input to the compressor motor plus heat absorbed in the evaporator equals the total heat rejected at the condenser ( Q condenser = Q evaporator + W compressor Q_{\text{condenser}} = Q_{\text{evaporator}} + W_{\text{compressor}} Q condenser = Q evaporator + W compressor ).
Second Law of Thermodynamics: Heat flows naturally and spontaneously from a warmer body (higher thermal intensity) to a cooler body (lower thermal intensity). Heat will never flow from a cold object to a hot object without external work being applied (work input by the compressor).
The Three Modes of Heat Transfer
Mode Mechanism HVAC Field Example
Conduction Transfer of heat energy through direct molecular contact within a solid material Heat moving through the copper wall of an evaporator tube from outdoor ambient air into liquid refrigerant
Convection Transfer of heat energy via fluid movement (liquid or gas) Forced air circulation over a heating element driven by a blower fan; water circulation through a chiller barrel
Radiation Thermal energy transfer via electromagnetic waves without heating the intervening space Radiant floor heating systems; solar heat gain striking a roof deck and windows
Temperature Scales & Conversions
Temperature measures the intensity of heat (average kinetic energy of molecules), whereas heat quantity measures total thermal energy contained in a mass.
Scale Definitions
Fahrenheit (°F): Imperial scale where water freezes at 32 ∘ F 32^\circ\text{F} 3 2 ∘ F and boils at 212 ∘ F 212^\circ\text{F} 21 2 ∘ F under standard atmospheric pressure ( 14.696 psia 14.696 \text{ psia} 14.696 psia ).
Celsius (°C): Metric scale where water freezes at 0 ∘ C 0^\circ\text{C} 0 ∘ C and boils at 100 ∘ C 100^\circ\text{C} 10 0 ∘ C .
Kelvin (K): Absolute metric scale where 0 K 0 \text{ K} 0 K represents absolute zero (complete cessation of molecular motion).
Rankine (°R): Absolute Imperial scale where 0 ∘ R 0^\circ\text{R} 0 ∘ R represents absolute zero ( − 459.67 ∘ F -459.67^\circ\text{F} − 459.6 7 ∘ F ).
Temperature Conversion Equations Fahrenheit to Celsius: ∘ C = ∘ F − 32 1.8 \text{Fahrenheit to Celsius: } ^\circ\text{C} = \frac{^\circ\text{F} - 32}{1.8} Fahrenheit to Celsius: ∘ C = 1.8 ∘ F − 32 Celsius to Fahrenheit: ∘ F = ( ∘ C × 1.8 ) + 32 \text{Celsius to Fahrenheit: } ^\circ\text{F} = (^\circ\text{C} \times 1.8) + 32 Celsius to Fahrenheit: ∘ F = ( ∘ C × 1.8 ) + 32 Kelvin: K = ∘ C + 273.15 \text{Kelvin: } \text{K} = ^\circ\text{C} + 273.15 Kelvin: K = ∘ C + 273.15 Rankine: ∘ R = ∘ F + 459.67 \text{Rankine: } ^\circ\text{R} = ^\circ\text{F} + 459.67 Rankine: ∘ R = ∘ F + 459.67
Heat Quantity Definitions: BTU & Ton of Refrigeration
British Thermal Unit (BTU): The amount of heat energy required to raise the temperature of 1 pound of pure liquid water by 1°F (specifically from 59.5 ∘ F 59.5^\circ\text{F} 59. 5 ∘ F to 60.5 ∘ F 60.5^\circ\text{F} 60. 5 ∘ F ).
Ton of Refrigeration: The cooling capacity equivalent to the heat absorbed by melting 1 ton ( 2 , 000 lbs 2,000 \text{ lbs} 2 , 000 lbs ) of pure ice at 32 ∘ F 32^\circ\text{F} 3 2 ∘ F into liquid water at 32 ∘ F 32^\circ\text{F} 3 2 ∘ F over a period of 24 hours . Latent Heat of Fusion of Water = 144 BTU/lb \text{Latent Heat of Fusion of Water} = 144 \text{ BTU/lb} Latent Heat of Fusion of Water = 144 BTU/lb Total Latent Heat = 2 , 000 lbs × 144 BTU/lb = 288 , 000 BTU per 24 hours \text{Total Latent Heat} = 2,000 \text{ lbs} \times 144 \text{ BTU/lb} = 288,000 \text{ BTU per 24 hours} Total Latent Heat = 2 , 000 lbs × 144 BTU/lb = 288 , 000 BTU per 24 hours Hourly Cooling Rate = 288 , 000 BTU 24 hours = 12 , 000 BTU/hr per Ton \text{Hourly Cooling Rate} = \frac{288,000 \text{ BTU}}{24 \text{ hours}} = \mathbf{12,000 \text{ BTU/hr per Ton}} Hourly Cooling Rate = 24 hours 288 , 000 BTU = 12 , 000 BTU/hr per Ton
Electrical Heat Equivalent: 1 Watt = 3.412 BTU/hr 1 \text{ Watt} = 3.412 \text{ BTU/hr} 1 Watt = 3.412 BTU/hr . A 5 kW 5 \text{ kW} 5 kW electric resistance heating element produces 5 , 000 × 3.412 = 17 , 060 BTU/hr 5,000 \times 3.412 = 17,060 \text{ BTU/hr} 5 , 000 × 3.412 = 17 , 060 BTU/hr .
Sensible Heat, Latent Heat, and Enthalpy
Thermal calculations require separating temperature-changing heat from phase-changing heat.
Sensible Heat ( Q s Q_s Q s )
Sensible heat added to or removed from a substance produces a direct change in temperature that can be measured with a standard dry-bulb thermometer. No phase change occurs. Q s = m × c × Δ T Q_s = m \times c \times \Delta T Q s = m × c × Δ T
Where m m m is mass (lbs), c c c is specific heat capacity ( BTU/lb ⋅ ∘ F \text{BTU/lb}\cdot^\circ\text{F} BTU/lb ⋅ ∘ F ), and Δ T \Delta T Δ T is temperature change ( ∘ F ^\circ\text{F} ∘ F ).
Specific Heat Capacity ( c c c ): The heat required to raise 1 lb of a substance by 1°F.
- Water: 1.00 BTU/lb ⋅ ∘ F 1.00 \text{ BTU/lb}\cdot^\circ\text{F} 1.00 BTU/lb ⋅ ∘ F
- Ice: 0.50 BTU/lb ⋅ ∘ F 0.50 \text{ BTU/lb}\cdot^\circ\text{F} 0.50 BTU/lb ⋅ ∘ F
- Steam: 0.48 BTU/lb ⋅ ∘ F 0.48 \text{ BTU/lb}\cdot^\circ\text{F} 0.48 BTU/lb ⋅ ∘ F
- Standard Air: 0.24 BTU/lb ⋅ ∘ F 0.24 \text{ BTU/lb}\cdot^\circ\text{F} 0.24 BTU/lb ⋅ ∘ F
- Latent Heat ( Q l Q_l Q l )
Latent heat added to or removed from a substance causes a change of state (phase change) with no change in temperature .
Latent Heat of Fusion: Heat required to change a solid to a liquid at its melting point ( 144 BTU/lb 144 \text{ BTU/lb} 144 BTU/lb for water at 32 ∘ F 32^\circ\text{F} 3 2 ∘ F ).
Latent Heat of Vaporization: Heat required to change a liquid to a vapor at its boiling point ( 970.4 BTU/lb 970.4 \text{ BTU/lb} 970.4 BTU/lb for water at 212 ∘ F 212^\circ\text{F} 21 2 ∘ F at sea level).
Total Heat / Enthalpy ( h h h )
Enthalpy is the total heat content of a substance above an arbitrary baseline ( 0 ∘ F 0^\circ\text{F} 0 ∘ F for refrigerants), combining both sensible and latent heat quantities ( h = Q s + Q l h = Q_s + Q_l h = Q s + Q l ).
Practical HVAC Field Calculations
Technicians calculate sensible, latent, and total heat rates for air and water streams using empirical field formulas.
Sensible Heat Formula for Airflow Q sensible = 1.08 × CFM × Δ T Q_{\text{sensible}} = 1.08 \times \text{CFM} \times \Delta T Q sensible = 1.08 × CFM × Δ T
Derivation of Constant 1.08: Density of Standard Air = 0.075 lbs/ft 3 \text{Density of Standard Air} = 0.075 \text{ lbs/ft}^3 Density of Standard Air = 0.075 lbs/ft 3 Specific Heat of Air = 0.24 BTU/lb ⋅ ∘ F \text{Specific Heat of Air} = 0.24 \text{ BTU/lb}\cdot^\circ\text{F} Specific Heat of Air = 0.24 BTU/lb ⋅ ∘ F Minutes per Hour = 60 \text{Minutes per Hour} = 60 Minutes per Hour = 60 Constant = 0.075 × 0.24 × 60 = 1.08 \text{Constant} = 0.075 \times 0.24 \times 60 = \mathbf{1.08} Constant = 0.075 × 0.24 × 60 = 1.08
Latent Heat Formula for Airflow Q latent = 0.68 × CFM × Δ W grains Q_{\text{latent}} = 0.68 \times \text{CFM} \times \Delta W_{\text{grains}} Q latent = 0.68 × CFM × Δ W grains
Where Δ W grains \Delta W_{\text{grains}} Δ W grains is the moisture content difference in grains of moisture per pound of dry air ( 7 , 000 grains = 1 lb of water 7,000 \text{ grains} = 1 \text{ lb of water} 7 , 000 grains = 1 lb of water ).
Total Heat Formula for Airflow & Sensible Heat Ratio Q total = 4.5 × CFM × Δ h Q_{\text{total}} = 4.5 \times \text{CFM} \times \Delta h Q total = 4.5 × CFM × Δ h
Where Δ h \Delta h Δ h is the enthalpy change in BTU/lb of dry air, derived from psychrometric wet-bulb temperatures. The Sensible Heat Ratio (SHR) indicates the proportion of total cooling that addresses sensible load: SHR = Q sensible Q total \text{SHR} = \frac{Q_{\text{sensible}}}{Q_{\text{total}}} SHR = Q total Q sensible
Hydronic Water Flow Sensible Heat Formula Q water = 500 × GPM × Δ T Q_{\text{water}} = 500 \times \text{GPM} \times \Delta T Q water = 500 × GPM × Δ T
Where GPM is Gallons Per Minute and 500 represents ( 8.33 lbs/gal × 60 min/hr × 1.0 sp. heat 8.33 \text{ lbs/gal} \times 60 \text{ min/hr} \times 1.0 \text{ sp. heat} 8.33 lbs/gal × 60 min/hr × 1.0 sp. heat ).