Study guide

5.4 Gas & Electric Heating Service: Ignition Controls, Heat Exchangers & Flame Sensors

NATE HVAC Certification Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

0.1 NATE Certification Pathways: CHP-5 vs. Traditional Core & Specialty 0.2 Exam Logistics, Scoring, EPA 608 Prerequisites & Recertification 0.3 Effective Study Strategies & Recommended Field Test Preparation

2 Chapter 1: HVAC Fundamentals & Safety

1.1 Personal & Job-Site Safety, PPE, Lockout/Tagout, and OSHA Compliance 1.2 Specialized HVAC Hand Tools, Vacuum Pumps, Manifold Gauges, and Meters 1.3 Principles of Heat Transfer, Temperature Scales, and Heat Quantity Calculations 1.4 The Vapor Compression Refrigeration Cycle & Component Roles 1.5 Refrigerant Classifications, Recovery/Recycling, and EPA Section 608 Laws

3 Chapter 2: Electrical Theory, Controls & Troubleshooting

2.1 Electrical Fundamentals, Ohm's Law, and Circuit Configurations 2.2 Electric Motors, Capacitors, Relays, Contactors, and Starters 2.3 Low-Voltage Controls, Thermostats, Transformers, and Safety Switches 2.4 Reading HVAC Schematics, Ladder Diagrams, and Wiring Diagrams 2.5 Systematic Electrical Troubleshooting & Multimeter Diagnostics

4 Chapter 3: Comfort, Airflow & Psychrometrics

3.1 Fundamentals of Indoor Air Quality (IAQ) and Human Comfort Parameters 3.2 Psychrometric Chart Fundamentals: Dry-Bulb, Wet-Bulb, Dew Point & Humidity 3.3 Airflow Dynamics, Duct Static Pressure, Velocity, and CFM Calculations 3.4 Ductwork Design, Blower Performance Curves, and Air Balancing 3.5 Ventilation Standards, Filtration Ratings (MERV), and Humidity Control

5 Chapter 4: Equipment Installation & Commissioning

4.1 Equipment Placement, Clearances, Mounting, and Code Compliance 4.2 Refrigerant Piping, Copper Tubing Prep, Nitrogen Purge, and Brazing 4.3 Deep Vacuum Evacuation, Micron Gauges, and System Dehydration 4.4 Refrigerant Charging Methods: Superheat, Subcooling, and Weigh-In 4.5 System Commissioning, Startup Checks, and Combustion Analysis

6 Chapter 5: Service, Diagnostics & Preventive Maintenance

5.1 Systematic Troubleshooting Workflow & Problem Identification 5.2 Compressor Diagnostics, Mechanical Failures, and Electrical Faults 5.3 Air Conditioning & Heat Pump Service: Reversing Valves, Defrost & Metering Devices 5.4 Gas & Electric Heating Service: Ignition Controls, Heat Exchangers & Flame Sensors 5.5 Preventive Maintenance Protocols, Seasonal Tune-Ups, and Customer Service

5.4 Gas & Electric Heating Service: Ignition Controls, Heat Exchangers & Flame Sensors

Key Takeaways Explain This Topic AI

Gas furnace flame rectification requires a microampere (uA) DC signal typically between 1.0 uA and 5.0 uA; readings below 0.5 uA trigger ignition module lockout.

Cracked heat exchangers present severe safety hazards including carbon monoxide (CO) leakage and flame rollout when the indoor blower energizes.

Hot surface igniters (HSI) constructed of silicon carbide typically measure 45 to 90 ohms room temperature resistance, whereas nitride igniters measure 11 to 20 ohms.

Electric resistance heating elements require verification of individual coil amperage, limit switch operation, and proper staging sequence via thermal time delay relays or sequencers.

Last updated: July 2026

5.4 Gas & Electric Heating Service: Ignition Controls, Heat Exchangers & Flame Sensors

Quick Summary: Servicing natural gas, propane, and electric heating equipment requires rigorous application of electrical sequence verification, flame rectification physics, igniter resistance specifications, and heat exchanger safety inspection protocols. Technicians must properly diagnose integrated control faults, measure microampere rectification signals, and perform combustion analysis to ensure safe, code-compliant furnace performance.

Sequence of Operation & Integrated Furnace Control (IFC) Diagnostics

Modern category I and category IV gas furnaces rely on an Integrated Furnace Control (IFC) microprocessor board to govern safety interlocks and ignition steps.

Standard Furnace Sequence of Operation

Call for Heat: Thermostat closes R-to-W (24 V AC).

Safety Check & Inducer Start: IFC verifies limit switches and roll-out switches are closed, then energizes the draft inducer motor.

Draft Proving: Inducer pulls negative draft pressure, closing the normal-open differential pressure switch (proving flue draft).

Pre-Purge & Igniter Warm-Up: IFC conducts a 15-to-30 second pre-purge of the heat exchanger, then energizes the Hot Surface Igniter (HSI) for 15-to-45 seconds.

Gas Valve Energization: IFC supplies 24 V AC to the main gas valve solenoid. Gas flows to burners and ignites off the HSI.

Flame Rectification Proving: Flame sensor generates a microamp DC signal within the 4-to-7 second Trial for Ignition (TFI) period.

Blower On-Delay: IFC turns on the indoor blower motor after 30 to 45 seconds.

Post-Purge & Blower Off-Delay: Thermostat satisfies (W opens). Gas valve closes instantly. Inducer runs a 15-second post-purge; indoor blower runs a 90-to-180 second heat off-delay.

Pressure Switch Diagnostics

Differential pressure switches monitor negative draft pressure generated by the inducer fan (typically -0.45" to -1.20" w.c. setpoints).

Stuck Open Error (Flash Code 2/3): Caused by a failed inducer motor, cracked sensing hose, restricted flue pipe, blocked secondary heat exchanger, or clogged condensate drain trap on 90%+ condensing furnaces.

Stuck Closed Error: IFC detects pressure switch contacts already closed prior to energizing inducer motor, shutting down ignition cycle for safety.

Flame Rectification Circuit & Troubleshooting

Flame rectification is the electrical process used by modern furnace ignition controls to verify flame presence safely.

The Physics of Flame Ionization

During combustion, burning gas molecules ionize, releasing free electrons into the flame matrix. The IFC applies an AC voltage (typically 80 V AC to 120 V AC) to the stainless steel flame sensor rod immersed in the burner flame.

Because the grounded burner surface area is dramatically larger than the thin flame rod surface area, electrons flow far more easily in one direction (from flame rod to ground) than the reverse.

This converts (rectifies) the AC voltage into a tiny Direct Current (DC) microampere (uA) signal that travels back through the furnace chassis ground to the IFC board.

Flame Sensor Diagnostic Procedure

Connect a digital multimeter in series with the flame sensor lead (set meter to DC Microamps uA).

Energize system call for heat and measure during ignition.

Normal Rectification Signal: 1.5 uA to 5.0 uA DC .

Dropout Threshold: Below 0.5 uA to 1.0 uA DC (causes safety lockout).

Cleaning Flame Sensors

Over time, non-conductive silicon dioxide (glass-like coating from airborne dust/silicon) coats the flame rod. Clean the rod using fine emery cloth or steel wool (never sand paper, which leaves quartz silica residue). Also inspect burner chassis ground wires for tight, corrosion-free connections.

Heat Exchanger Integrity & Safety Diagnostics

A breached heat exchanger poses a severe life-safety threat by allowing poisonous carbon monoxide (CO) gas and flue products to mix into the supply air stream.

Inspection & Diagnostic Methods

Visual & Borescope Inspection: Inspect internal clamshell stress cracks, header box seam separations, and secondary condensing coil corrosion.

Blower Energization Flame Observation Test: Observe main burner flame characteristics while manually energizing the indoor blower motor.

Pass: Flame remains stable, steady blue, and unchanged.

Fail: Flame dances, lifts off burner ports, changes color to yellow, or rolls outward. This proves supply air pressure from the blower is entering the combustion chamber through a crack.

Flue Gas & Ambient CO Testing: Measure CO in flue gas using an electronic combustion analyzer (should be < 100 ppm CO air-free). Any detectable CO in supply plenum ducts requires immediate system shutdown and furnace replacement.

  • Hot Surface Igniters & Electric Heating Staging
  • Igniter Diagnostic Values

Silicon Carbide Igniters: 120V flat/mini-igniters. Cold room temperature resistance measures 45 to 90 ohms . Resistance increases significantly when hot.

Silicon Nitride Igniters: Modern durable 120V/24V igniters. Cold resistance measures 11 to 20 ohms .

Failure mode: An igniter with an open circuit (infinite resistance) or resistance exceeding 120 ohms must be replaced.

Electric Heat Elements & Sequencer Staging

Electric resistance furnaces utilize nickel-chromium (Ni-Cr) heating elements staged by bimetal thermal sequencers.

Sequencer Function: Sequencers delay element activation (typically 15 to 45 seconds) to prevent sudden electrical grid surge currents and eliminate cold air blasts.

Amperage & Resistance Calculation: For a 5 kW element rated at 240V: I = Watts Volts = 5000 W 240 V = 20.83 A I = \frac{\text{Watts}}{\text{Volts}} = \frac{5000\text{ W}}{240\text{ V}} = 20.83\text{ A} I = Volts Watts ​ = 240 V 5000 W ​ = 20.83 A R = Volts Amps = 240 V 20.83 A = 11.52 Ω R = \frac{\text{Volts}}{\text{Amps}} = \frac{240\text{ V}}{20.83\text{ A}} = 11.52\ \Omega R = Amps Volts ​ = 20.83 A 240 V ​ = 11.52 Ω

  • Furnace Component Normal Electrical Value Malfunction Threshold Primary Failure Cause
  • Silicon Carbide HSI 45 ohms to 90 ohms cold > 110 ohms or Open (O.L.) Thermal shock, hairline fracture
  • Silicon Nitride HSI 11 ohms to 20 ohms cold > 30 ohms or Open (O.L.) Impact damage, physical stress
  • Flame Sensor Current 1.5 uA to 5.0 uA DC < 0.8 uA DC Oxide coating, poor burner ground
  • 5 kW Heat Element (240V) 20.8 A / 11.5 ohms 0 A (Open circuit) Blown fusible link, open limit

Loading diagram... Gas Furnace Ignition & Safety Sequence Flowchart