Study guide
6.1 Fan Laws, Airflow Dynamics & Total External Static Pressure
North Carolina HVAC Contractor License Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: North Carolina HVAC Licensing Framework & Board Jurisprudence
1.1 NC Dual-Board Regulatory Structure & General Statutes 1.2 Heating Classifications, Groups & Scopes 1.3 Examination Prerequisites, Qualifier Responsibilities & Disciplinary Rules 1.4 Examination Logistics, Reference Books & Code Editions
2 Chapter 2: North Carolina Business Organizations, Contracts & Lien Law
2.1 Construction Contracts, Project Management & Bidding 2.2 North Carolina Mechanics' Lien Law & Bond Claims 2.3 Business Organizations, Financial Management & Taxation
3 Chapter 3: Construction Safety, Electrical Safety & EPA 608
3.1 OSHA 1926 Construction Safety & Job Site Protocols 3.2 Electrical Safety, NFPA 70E & Lockout/Tagout (LOTO) 3.3 EPA Section 608 & Refrigerant Transition Regulations
4 Chapter 4: Thermodynamics, Refrigeration Cycle & Psychrometrics
4.1 Fundamentals of Thermodynamics & Heat Transfer 4.2 The Mechanical Refrigeration Cycle & Component Dynamics 4.3 Psychrometric Properties, Air Processes & Chart Navigation
5 Chapter 5: ACCA Manual J & Manual N Load Calculations
5.1 Manual J Design Conditions & Thermal Parameters 5.2 Fenestration, Opaque Envelope & Internal Heat Gains 5.3 Infiltration, Duct Losses & Total Block Load Synthesis 5.4 ACCA Manual N Commercial Load Calculation
6 Chapter 6: ACCA Manual D & Manual Q Duct Design & Air Distribution
6.1 Fan Laws, Airflow Dynamics & Total External Static Pressure 6.2 ACCA Manual D Sizing Protocol & Friction Rate Calculation 6.3 SMACNA Duct Construction, Fittings & Air Balancing 6.4 ACCA Manual Q Commercial Low-Pressure Duct Design
7 Chapter 7: Forced Air Heating, Gas Furnaces & Fuel Piping
7.1 Natural Gas & Propane Combustion Fundamentals 7.2 Gas Furnace Operation, Sequence of Control & Diagnostics 7.3 Fuel Oil Heating Systems & Code-Compliant Fuel Gas Piping
8 Chapter 8: Heat Pumps, Inverters & Commercial System Selection (Manual CS)
8.1 Heat Pump Operating Principles, Reversing Valves & Physics 8.2 Defrost Controls, Supplemental Electric Heat & Balance Points 8.3 Inverter Mini-Splits & Variable Refrigerant Flow (VRF) Systems 8.4 Manual CS: Commercial Applications, Systems & Equipment
9 Chapter 9: Hydronic Heating, Steam Systems & Boilers (H1)
9.1 Hydronic Fundamentals, Boiler Classifications & Steam Systems 9.2 Hydronic Piping Layouts, Circulator Pumps & Head Loss Calculations 9.3 Boiler Trim, Expansion Tanks, Air Elimination & Safety Controls 9.4 The NC Uniform Boiler & Pressure Vessel Act (H1 Reference)
10 Chapter 10: Commercial Refrigeration & NC Board Regulations
10.1 NC State Board of Refrigeration Contractors Statutes & Licensure 10.2 Commercial Refrigeration Systems, Multiplex Racks & Defrost Protocols 10.3 Walk-In Coolers, Freezers, Evaporator Pressure Regulators & Valves
11 Chapter 11: NC Administration, Mechanical, Fuel Gas & Energy Codes
11.1 North Carolina Mechanical Code: Equipment Access, Clearances & Condensate 11.2 Ventilation Rates, Exhaust Systems & Duct Smoke Detection 11.3 NC Fuel Gas Code: Combustion Air, Venting & Gas Appliance Installation 11.4 NC Energy Conservation Code: Duct Testing, Envelope & Efficiency Standards 11.5 NC Administrative Code & Policies: Permits, Inspections & Plan Review
12 Chapter 12: Electrical Fundamentals, Motor Controls & Diagnostics
12.1 HVAC Electrical Fundamentals, Circuit Schematics & Power Distribution 12.2 Electric Motors, Capacitors & Motor Controls 12.3 Systematic HVAC Diagnostics, Superheat/Subcooling & Airflow Troubleshooting 12.4 System Commissioning, Testing, Adjusting & Balancing (TAB)
6.1 Fan Laws, Airflow Dynamics & Total External Static Pressure
Key Takeaways Explain This Topic AI
The three fundamental Fan Laws dictate that volumetric airflow varies directly with fan speed ratio (CFM ∝ RPM), static pressure varies with the square of the speed ratio (SP ∝ RPM²), and brake horsepower varies with the cube of the speed ratio (BHP ∝ RPM³).
Total Pressure (TP) is the algebraic sum of Static Pressure (SP) and Velocity Pressure (VP), where air velocity in standard air (density 0.075 lb/cu ft) is calculated as V = 4005 × √(VP) in feet per minute.
Total External Static Pressure (TESP) quantifies the external ductwork and component resistance against which the blower operates, measured as the absolute sum of supply plenum static pressure and return plenum static pressure.
Electrically Commutated Motors (ECM) maintain programmed CFM across rising static pressure by increasing rotor torque and wattage, whereas Permanent Split Capacitor (PSC) motors experience severe airflow drop-offs under elevated static.
System Effect Factors (SEF) resulting from poor fan inlet conditions or abrupt discharge elbows create non-uniform velocity profiles that degrade field airflow far below manufacturer ratings.
Last updated: August 2026
Fan Laws, Airflow Dynamics & Total External Static Pressure
Quick Reference: In HVAC air distribution, airflow ( C F M CFM CFM ), static pressure ( S P SP SP ), and fan power ( B H P BHP B H P ) are governed by the Affinitive Fan Laws . Standard air density is 0.075 lb/ft 3 0.075\text{ lb/ft}^3 0.075 lb/ft 3 at sea level ( 70 ∘ F 70^\circ\text{F} 7 0 ∘ F , 29.92 in. Hg 29.92\text{ in. Hg} 29.92 in. Hg ). Air velocity ( V V V ) is derived from velocity pressure ( V P VP V P ) via the standard formula V = 4005 V P V = 4005 \sqrt{VP} V = 4005 V P . Total External Static Pressure (TESP) is the sum of the absolute static pressure measured at the supply plenum and return plenum: TESP = ∣ S P supply ∣ + ∣ S P return ∣ \text{TESP} = |SP_{\text{supply}}| + |SP_{\text{return}}| TESP = ∣ S P supply ∣ + ∣ S P return ∣ .
1. The Three Fundamental Fan Laws
The fan laws (affinitive laws) predict performance changes in centrifugal blowers and axial fans when rotational speed ( R P M RPM RPM ), impeller diameter ( D D D ), or air density ( ρ \rho ρ ) changes. For a fixed fan diameter and constant air density, the three operational fan laws are:
Fan Law 1: Airflow vs. Fan Speed (Linear Relationship)
Volumetric airflow rate ( C F M CFM CFM ) varies directly and linearly with fan rotational speed ( R P M RPM RPM ): C F M 2 C F M 1 = R P M 2 R P M 1 ⟹ C F M 2 = C F M 1 × ( R P M 2 R P M 1 ) \frac{CFM_2}{CFM_1} = \frac{RPM_2}{RPM_1} \quad \implies \quad CFM_2 = CFM_1 \times \left( \frac{RPM_2}{RPM_1} \right) CF M 1 CF M 2 = RP M 1 RP M 2 ⟹ CF M 2 = CF M 1 × ( RP M 1 RP M 2 )
Fan Law 2: Static Pressure vs. Fan Speed (Square Relationship)
Static pressure ( S P SP SP ), velocity pressure ( V P VP V P ), and total pressure ( T P TP TP ) vary with the square of the fan speed ratio: S P 2 S P 1 = ( R P M 2 R P M 1 ) 2 = ( C F M 2 C F M 1 ) 2 ⟹ S P 2 = S P 1 × ( R P M 2 R P M 1 ) 2 \frac{SP_2}{SP_1} = \left( \frac{RPM_2}{RPM_1} \right)^2 = \left( \frac{CFM_2}{CFM_1} \right)^2 \quad \implies \quad SP_2 = SP_1 \times \left( \frac{RPM_2}{RPM_1} \right)^2 S P 1 S P 2 = ( RP M 1 RP M 2 ) 2 = ( CF M 1 CF M 2 ) 2 ⟹ S P 2 = S P 1 × ( RP M 1 RP M 2 ) 2
Fan Law 3: Power vs. Fan Speed (Cubic Relationship)
Brake Horsepower ( B H P BHP B H P ) and electrical power consumption vary with the cube of the fan speed ratio (and cube of the airflow ratio): B H P 2 B H P 1 = ( R P M 2 R P M 1 ) 3 = ( C F M 2 C F M 1 ) 3 ⟹ B H P 2 = B H P 1 × ( R P M 2 R P M 1 ) 3 \frac{BHP_2}{BHP_1} = \left( \frac{RPM_2}{RPM_1} \right)^3 = \left( \frac{CFM_2}{CFM_1} \right)^3 \quad \implies \quad BHP_2 = BHP_1 \times \left( \frac{RPM_2}{RPM_1} \right)^3 B H P 1 B H P 2 = ( RP M 1 RP M 2 ) 3 = ( CF M 1 CF M 2 ) 3 ⟹ B H P 2 = B H P 1 × ( RP M 1 RP M 2 ) 3 Fan Law Summary Ratios:
- Speed Multiplier (x): 1.00 1.10 (+10%) 1.20 (+20%) 1.30 (+30%)
- Airflow (CFM = x^1): 1.00 1.10 (+10%) 1.20 (+20%) 1.30 (+30%)
- Static Pressure (SP = x^2): 1.00 1.21 (+21%) 1.44 (+44%) 1.69 (+69%)
- Power Draw (BHP = x^3): 1.00 1.33 (+33%) 1.73 (+73%) 2.20 (+120%)
- Pulley & Sheave Ratio Dynamics
For belt-driven commercial air handlers and packaged rooftop units, fan speed adjustments are made using adjustable pitch motor sheaves or replacement pulleys: D motor × R P M motor = D fan × R P M fan D_{\text{motor}} \times RPM_{\text{motor}} = D_{\text{fan}} \times RPM_{\text{fan}} D motor × RP M motor = D fan × RP M fan R P M fan = R P M motor × ( D motor D fan ) RPM_{\text{fan}} = RPM_{\text{motor}} \times \left( \frac{D_{\text{motor}}}{D_{\text{fan}}} \right) RP M fan = RP M motor × ( D fan D motor )
Where D motor D_{\text{motor}} D motor is the pitch diameter of the motor drive sheave, and D fan D_{\text{fan}} D fan is the pitch diameter of the blower pulley.
Worked Example: Fan Law Calculations & Motor Loading
A commercial belt-driven air handler currently operates at 800 RPM 800\text{ RPM} 800 RPM with a 1.5 HP 1.5\text{ HP} 1.5 HP motor delivering 2 , 400 CFM 2,400\text{ CFM} 2 , 400 CFM against an external static pressure of 0.60 in. w.c. 0.60\text{ in. w.c.} 0.60 in. w.c. The measured operating brake horsepower is 1.20 BHP 1.20\text{ BHP} 1.20 BHP . The commissioning engineer requires an increase in airflow to 2 , 760 CFM 2,760\text{ CFM} 2 , 760 CFM ( + 15 % +15\% + 15% increase).
Calculate Required Fan Speed ( R P M 2 RPM_2 RP M 2 ): R P M 2 = 800 × ( 2760 2400 ) = 800 × 1.15 = 920 RPM RPM_2 = 800 \times \left( \frac{2760}{2400} \right) = 800 \times 1.15 = 920\text{ RPM} RP M 2 = 800 × ( 2400 2760 ) = 800 × 1.15 = 920 RPM
Calculate New Static Pressure ( S P 2 SP_2 S P 2 ): S P 2 = 0.60 × ( 1.15 ) 2 = 0.60 × 1.3225 = 0.7935 in. w.c. SP_2 = 0.60 \times (1.15)^2 = 0.60 \times 1.3225 = 0.7935\text{ in. w.c.} S P 2 = 0.60 × ( 1.15 ) 2 = 0.60 × 1.3225 = 0.7935 in. w.c.
Calculate New Power Requirement ( B H P 2 BHP_2 B H P 2 ): B H P 2 = 1.20 × ( 1.15 ) 3 = 1.20 × 1.520875 = 1.825 BHP BHP_2 = 1.20 \times (1.15)^3 = 1.20 \times 1.520875 = 1.825\text{ BHP} B H P 2 = 1.20 × ( 1.15 ) 3 = 1.20 × 1.520875 = 1.825 BHP
Motor Sizing Evaluation: The existing 1.5 HP 1.5\text{ HP} 1.5 HP motor has a full-load rating of 1.50 BHP 1.50\text{ BHP} 1.50 BHP (or 1.725 BHP 1.725\text{ BHP} 1.725 BHP assuming a standard 1.15 1.15 1.15 service factor). Operating at 1.825 BHP 1.825\text{ BHP} 1.825 BHP will cause continuous motor overload, tripping the thermal overload or burning out windings. The motor must be upgraded to a 2.0 HP 2.0\text{ HP} 2.0 HP or 3.0 HP 3.0\text{ HP} 3.0 HP motor before increasing sheave pitch.
2. Airflow Dynamics: Total, Static & Velocity Pressure
Air moving through ductwork exerts three distinct pressure components governed by Bernoulli's conservation of energy principle:
Pressure Component Definition Physical Characteristic Measurement Instrument
Static Pressure ( S P SP SP ) Outward radial force exerted equally in all directions against duct walls Potential energy; pushes air against friction and fitting restrictions Static pressure tip perpendicular to flow
Velocity Pressure ( V P VP V P ) Forward kinetic pressure caused by the directional speed of moving air Kinetic energy; always positive in the direction of airflow Pitot tube facing directly into airflow
Total Pressure ( T P TP TP ) Total mechanical energy of the air stream Algebraic sum: T P = S P + V P TP = SP + VP TP = SP + V P Impact tube opening pointing into flow T P = S P + V P ⟺ V P = T P − S P TP = SP + VP \quad \iff \quad VP = TP - SP TP = SP + V P ⟺ V P = TP − SP
Air Velocity & Flow Rate Equations
At standard air density ( ρ = 0.075 lb/ft 3 \rho = 0.075\text{ lb/ft}^3 ρ = 0.075 lb/ft 3 , corresponding to dry air at 70 ∘ F 70^\circ\text{F} 7 0 ∘ F and 29.92 in. Hg 29.92\text{ in. Hg} 29.92 in. Hg barometric pressure), air velocity ( V V V ) in feet per minute (FPM) is derived from velocity pressure ( V P VP V P ) in inches water column (in. w.c.): V = 4005 × V P V = 4005 \times \sqrt{VP} V = 4005 × V P V P = ( V 4005 ) 2 VP = \left( \frac{V}{4005} \right)^2 V P = ( 4005 V ) 2
Once velocity is determined, volumetric flow rate ( Q Q Q or C F M CFM CFM ) is calculated across the duct cross-sectional area ( A A A in square feet): C F M = V × A = 4005 × V P × ( Duct Width (in) × Duct Height (in) 144 ) CFM = V \times A = 4005 \times \sqrt{VP} \times \left( \frac{\text{Duct Width (in)} \times \text{Duct Height (in)}}{144} \right) CFM = V × A = 4005 × V P × ( 144 Duct Width (in) × Duct Height (in) )
Pitot Tube Duct Traverse (AMCA 204 / ASHRAE 111)
Because air velocity is not uniform across a duct—flowing faster in the center due to boundary layer wall friction—field airflow cannot be determined from a single centerline measurement. Technicians perform a Pitot Tube Traverse using equal-area grids or log-Tchebycheff spacing:
Rectangular Ducts: Minimum of 16 to 24 traverse points divided into equal rectangular sub-areas (4×4 or 5×5 grid).
Round Ducts: Minimum of two traverses at 90 ∘ 90^\circ 9 0 ∘ to each other, taking 6 to 10 points along each diameter.
True Average Velocity: Average the square roots of the velocity pressures, not the raw velocity pressures: V avg = 4005 × ( ∑ i = 1 n V P i n ) V_{\text{avg}} = 4005 \times \left( \frac{\sum_{i=1}^n \sqrt{VP_i}}{n} \right) V avg = 4005 × ( n ∑ i = 1 n V P i )
3. Total External Static Pressure (TESP) Measurement
Total External Static Pressure is the primary diagnostic metric used to verify that an installed HVAC system can deliver design airflow without overheating, freezing the evaporator coil, or over-amping the blower motor.
- Static Pressure Measurement Locations RETURN DUCTWORK AIR HANDLER / FURNACE SUPPLY PLENUM
- [Return Grille] ===> (Filter) ===> [Blower] ===> [Heat Exchanger / Coil] ===> [Supply Trunk]
- | | |
- Port 1 (Blower) Port 2
- Return Static Supply Static
- (-0.35 in. wc) (+0.20 in. wc)
Furnace with External Cased Evaporator Coil:
Return Static ( S P return SP_{\text{return}} S P return ): Measure in the return drop between the air filter and the furnace blower cabinet entrance (negative pressure).
Supply Static ( S P supply SP_{\text{supply}} S P supply ): Measure in the supply transition between the top of the furnace heat exchanger and the bottom of the cased evaporator coil (positive pressure).
Note: If measuring external to the entire package (including cased coil), supply static is taken downstream of the coil in the supply plenum, and the coil pressure drop must be accounted for.
Modular Air Handler / Packaged Heat Pump (Internal Coil):
Return Static: In the return plenum immediately before the air handler cabinet inlet.
Supply Static: In the supply trunk approximately 1 to 2 feet downstream of the air handler discharge.
TESP Calculation Formula TESP = ∣ S P supply ∣ + ∣ S P return ∣ \text{TESP} = |SP_{\text{supply}}| + |SP_{\text{return}}| TESP = ∣ S P supply ∣ + ∣ S P return ∣ TESP = S P supply − S P return ( where S P return is a negative value ) \text{TESP} = SP_{\text{supply}} - SP_{\text{return}} \quad (\text{where } SP_{\text{return}} \text{ is a negative value}) TESP = S P supply − S P return ( where S P return is a negative value )
Example: If supply plenum static pressure is + 0.22 in. w.c. +0.22\text{ in. w.c.} + 0.22 in. w.c. and return plenum static pressure is − 0.38 in. w.c. -0.38\text{ in. w.c.} − 0.38 in. w.c. , the Total External Static Pressure is: TESP = ∣ + 0.22 ∣ + ∣ − 0.38 ∣ = 0.60 in. w.c. \text{TESP} = |+0.22| + |-0.38| = 0.60\text{ in. w.c.} TESP = ∣ + 0.22∣ + ∣ − 0.38∣ = 0.60 in. w.c.
4. Component Pressure Drops ( C P S C CPSC CPSC )
When evaluating Available Static Pressure ( A S P ASP A SP ) for Manual D duct design, contractors must account for internal and external accessory pressure drops:
Component Typical Pressure Drop Range (in. w.c.) Key Variables Influencing Loss
Dry DX Evaporator Coil 0.15 − 0.25 in. w.c. 0.15 - 0.25\text{ in. w.c.} 0.15 − 0.25 in. w.c. Fin density (FPI), face area, circuiting
Wet DX Evaporator Coil (Dehumidifying) 0.20 − 0.35 in. w.c. 0.20 - 0.35\text{ in. w.c.} 0.20 − 0.35 in. w.c. Condensed water film bridges fin gaps ( + 20 % +20\% + 20% to + 40 % +40\% + 40% vs. dry)
Standard 1" Fiberglass Filter 0.05 − 0.10 in. w.c. 0.05 - 0.10\text{ in. w.c.} 0.05 − 0.10 in. w.c. Dust loading, low arrestance (MERV 2–4)
High-Efficiency 1" Pleated Filter (MERV 11–13) 0.20 − 0.40 in. w.c. 0.20 - 0.40\text{ in. w.c.} 0.20 − 0.40 in. w.c. High restriction at standard 300 − 500 FPM 300-500\text{ FPM} 300 − 500 FPM face velocities
Deep 4"–5" Media Filter (MERV 11–16) 0.10 − 0.18 in. w.c. 0.10 - 0.18\text{ in. w.c.} 0.10 − 0.18 in. w.c. Expanded surface area reduces face velocity and resistance
Electric Resistance Heating Element 0.03 − 0.08 in. w.c. 0.03 - 0.08\text{ in. w.c.} 0.03 − 0.08 in. w.c. Kilowatt rack density, coil open-wire spacing
Supply Diffusers / Registers 0.03 − 0.05 in. w.c. 0.03 - 0.05\text{ in. w.c.} 0.03 − 0.05 in. w.c. Grille damper position, blade throw configuration
Return Filter Grille (including filter) 0.15 − 0.25 in. w.c. 0.15 - 0.25\text{ in. w.c.} 0.15 − 0.25 in. w.c. Grille free area ( A k A_k A k ), filter loading
UV Germicidal / Electronic Air Cleaner 0.02 − 0.06 in. w.c. 0.02 - 0.06\text{ in. w.c.} 0.02 − 0.06 in. w.c. Lamp rack aerodynamic obstruction
5. Fan Motor Technologies: PSC vs. ECM
Modern residential and light commercial HVAC equipment utilizes two primary blower motor architectures with drastically different pressure-airflow responses: Airflow (CFM)
- ^
- | [Constant-Airflow ECM: Maintains CFM across rising static by ramping RPM]
- | ------------------------------------
- | \
- | [PSC Motor: Airflow drops steeply as static increases] \
- | \\ \
- | \\ \
- | \\ \
- +-------------------------------------------------------------------> Static Pressure (in. wc)
- 0.2 0.4 0.6 0.8 1.0 1.2
- Permanent Split Capacitor (PSC) Motors
Operating Principle: Single-phase induction motor with fixed speed taps (Low, Med-Low, Med-High, High). Operates on a fixed rotor torque curve.
Static Pressure Response: As duct static pressure rises (e.g., from a dirty filter or undersized ducts), blower speed drops, and volumetric airflow ( C F M CFM CFM ) declines rapidly.
Consequences of High Static: In cooling mode, low CFM causes evaporator coil freeze-up and liquid refrigerant floodback to the compressor. In heating mode, low CFM trips the furnace high-limit switch.
Electrically Commutated Motors (ECM)
Constant-Torque ECM (X13 / Endura Pro): Direct-current brushless motor with electronic commutation. Maintains fixed torque settings; airflow declines moderately with rising static pressure, but less severely than PSC.
Constant-Airflow ECM (Variable Speed 2.0 / 3.0): Microprocessor-controlled feedback loop continuously monitors motor speed ( R P M RPM RPM ) and back-EMF (torque). As static pressure rises, the motor automatically increases speed and wattage to deliver constant programmed CFM up to its maximum design limit (typically 0.80 − 1.00 in. w.c. 0.80 - 1.00\text{ in. w.c.} 0.80 − 1.00 in. w.c. ).
High Static ECM Trap: When static pressure exceeds 0.80 in. w.c. 0.80\text{ in. w.c.} 0.80 in. w.c. , ECM blowers draw maximum electrical wattage, generate excessive aerodynamic noise, and may experience thermal failure of the electronic control module.
6. System Effect Factors (SEF)
System Effect is the loss in fan performance resulting from poor aerodynamic inlet or outlet duct connections. Fan performance tables published by manufacturers (such as AMCA-certified ratings) are measured under ideal laboratory conditions with long, straight duct runs.
Common Field System Effect Causes
Abrupt Discharge Elbows: Installing a 90 ∘ 90^\circ 9 0 ∘ mitered elbow immediately at the blower discharge creates high localized turbulence and prevents static pressure regain. AMCA standard 200 recommends a minimum of 2.5 to 4.0 equivalent duct diameters 2.5\text{ to }4.0\text{ equivalent duct diameters} 2.5 to 4.0 equivalent duct diameters of straight discharge duct to achieve 100 % 100\% 100% effective recovery.
Eccentric Inlets: Sharp bends or offsets entering the blower inlet induce pre-rotation (swirl), cutting fan capacity by 15 % 15\% 15% to 30 % 30\% 30% .
Inlet Obstructions: Placing filters, structural joists, or sharp transitions closer than one fan inlet diameter to the blower suction opening.