Study guide

6.4 ACCA Manual Q Commercial Low-Pressure Duct Design

North Carolina HVAC Contractor License Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: North Carolina HVAC Licensing Framework & Board Jurisprudence

1.1 NC Dual-Board Regulatory Structure & General Statutes 1.2 Heating Classifications, Groups & Scopes 1.3 Examination Prerequisites, Qualifier Responsibilities & Disciplinary Rules 1.4 Examination Logistics, Reference Books & Code Editions

2 Chapter 2: North Carolina Business Organizations, Contracts & Lien Law

2.1 Construction Contracts, Project Management & Bidding 2.2 North Carolina Mechanics' Lien Law & Bond Claims 2.3 Business Organizations, Financial Management & Taxation

3 Chapter 3: Construction Safety, Electrical Safety & EPA 608

3.1 OSHA 1926 Construction Safety & Job Site Protocols 3.2 Electrical Safety, NFPA 70E & Lockout/Tagout (LOTO) 3.3 EPA Section 608 & Refrigerant Transition Regulations

4 Chapter 4: Thermodynamics, Refrigeration Cycle & Psychrometrics

4.1 Fundamentals of Thermodynamics & Heat Transfer 4.2 The Mechanical Refrigeration Cycle & Component Dynamics 4.3 Psychrometric Properties, Air Processes & Chart Navigation

5 Chapter 5: ACCA Manual J & Manual N Load Calculations

5.1 Manual J Design Conditions & Thermal Parameters 5.2 Fenestration, Opaque Envelope & Internal Heat Gains 5.3 Infiltration, Duct Losses & Total Block Load Synthesis 5.4 ACCA Manual N Commercial Load Calculation

6 Chapter 6: ACCA Manual D & Manual Q Duct Design & Air Distribution

6.1 Fan Laws, Airflow Dynamics & Total External Static Pressure 6.2 ACCA Manual D Sizing Protocol & Friction Rate Calculation 6.3 SMACNA Duct Construction, Fittings & Air Balancing 6.4 ACCA Manual Q Commercial Low-Pressure Duct Design

7 Chapter 7: Forced Air Heating, Gas Furnaces & Fuel Piping

7.1 Natural Gas & Propane Combustion Fundamentals 7.2 Gas Furnace Operation, Sequence of Control & Diagnostics 7.3 Fuel Oil Heating Systems & Code-Compliant Fuel Gas Piping

8 Chapter 8: Heat Pumps, Inverters & Commercial System Selection (Manual CS)

8.1 Heat Pump Operating Principles, Reversing Valves & Physics 8.2 Defrost Controls, Supplemental Electric Heat & Balance Points 8.3 Inverter Mini-Splits & Variable Refrigerant Flow (VRF) Systems 8.4 Manual CS: Commercial Applications, Systems & Equipment

9 Chapter 9: Hydronic Heating, Steam Systems & Boilers (H1)

9.1 Hydronic Fundamentals, Boiler Classifications & Steam Systems 9.2 Hydronic Piping Layouts, Circulator Pumps & Head Loss Calculations 9.3 Boiler Trim, Expansion Tanks, Air Elimination & Safety Controls 9.4 The NC Uniform Boiler & Pressure Vessel Act (H1 Reference)

10 Chapter 10: Commercial Refrigeration & NC Board Regulations

10.1 NC State Board of Refrigeration Contractors Statutes & Licensure 10.2 Commercial Refrigeration Systems, Multiplex Racks & Defrost Protocols 10.3 Walk-In Coolers, Freezers, Evaporator Pressure Regulators & Valves

11 Chapter 11: NC Administration, Mechanical, Fuel Gas & Energy Codes

11.1 North Carolina Mechanical Code: Equipment Access, Clearances & Condensate 11.2 Ventilation Rates, Exhaust Systems & Duct Smoke Detection 11.3 NC Fuel Gas Code: Combustion Air, Venting & Gas Appliance Installation 11.4 NC Energy Conservation Code: Duct Testing, Envelope & Efficiency Standards 11.5 NC Administrative Code & Policies: Permits, Inspections & Plan Review

12 Chapter 12: Electrical Fundamentals, Motor Controls & Diagnostics

12.1 HVAC Electrical Fundamentals, Circuit Schematics & Power Distribution 12.2 Electric Motors, Capacitors & Motor Controls 12.3 Systematic HVAC Diagnostics, Superheat/Subcooling & Airflow Troubleshooting 12.4 System Commissioning, Testing, Adjusting & Balancing (TAB)

6.4 ACCA Manual Q Commercial Low-Pressure Duct Design

Key Takeaways Explain This Topic AI

ACCA Manual Q (Commercial Low Pressure, Low Velocity Duct System Design) is a required reference for the Heating Group 1 Class I, Heating Group 2 and Heating Group 3 Class I examinations, and it is the commercial counterpart to the residential Manual D.

Low pressure means a system operating at 2 inches w.g. or less of duct static pressure; low velocity in commercial trunks generally means holding main duct velocity at or below about 2,000 FPM to control regenerated noise.

The three classical commercial sizing methods are equal friction, static regain and velocity reduction; equal friction is the Manual Q default for low-pressure work, while static regain is reserved for long, high-velocity supply mains.

Duct pressure class is selected from the maximum static pressure the section will see, and SMACNA construction tables for gauge, reinforcement spacing and seal class are then read against that pressure class.

System effect is the pressure penalty created by poor fan inlet and outlet connections; it is not measured by the balancer's manometer and must be added to the calculated system pressure loss before the fan is selected.

Last updated: August 2026

ACCA Manual Q Commercial Low-Pressure Duct Design

Where it sits: Manual D sizes residential duct; Manual Q — Commercial Low Pressure, Low Velocity Duct System Design sizes the small commercial systems an H2 or H3-I contractor actually installs. Heating Group 2 candidates carry Manual Q and Manual N but not Manual D or Manual J.

1. What "Low Pressure, Low Velocity" Actually Means

The terms are classification language, not adjectives.

Classification Static Pressure Range Typical Velocity Where Used

Low pressure 2 in. w.g. and below 2,000 FPM and below in mains Packaged rooftop units, split systems, small VAV, the bulk of NC small commercial

  • Medium pressure Above 2 up to 6 in. w.g. 2,000 – 4,000 FPM Larger VAV primary mains
  • High pressure Above 6 in. w.g. Above 4,000 FPM Central-plant primary distribution

Manual Q addresses the first row. A packaged rooftop unit with 1.0 in. w.g. of available external static pressure has no headroom for a duct system designed as though it were a medium-pressure trunk.

Pressure Class and Construction

Duct pressure class is a construction specification, not a performance measurement. SMACNA classes are ± \pm ± 0.5, 1, 2, 3, 4, 6 and 10 in. w.g. The designer assigns each duct section the class matching the maximum static pressure that section will see , then reads gauge, reinforcement spacing, and seal class from the SMACNA tables for that class.

Supply duct upstream of a VAV terminal sees the fan discharge pressure; downstream duct sees only the terminal's discharge pressure and drops a class or two.

Return and exhaust duct is under negative pressure and must resist collapse, which is a separate table.

Over-specifying pressure class buys heavier gauge and more reinforcement than the job needs; under-specifying produces panel rumble, seam separation and leakage.

  • 2. The Three Sizing Methods
  • Equal Friction — the Manual Q Default

Every duct section is sized to the same friction rate in inches of water gauge per 100 feet of equivalent length. It is simple, self-balancing enough for short, compact low-pressure systems, and it is the method the ACCA duct slide rule (Book R on the Board's list) implements directly. F R = A S P × 100 T E L FR = \frac{ASP \times 100}{TEL} FR = TE L A SP × 100 ​

where ASP is the static pressure available for the duct after every component loss is subtracted, and TEL is the total effective length of the longest supply-plus-return path.

Typical commercial low-pressure friction rates land between 0.08 and 0.10 in. w.g. per 100 ft . The rate is a result , not a preference: if the calculation returns 0.04 the ducts will be large and the job expensive; if it returns 0.20 the system will be noisy and the fan will not deliver.

Static Regain

As air leaves each branch takeoff, the velocity in the downstream main falls. Bernoulli's relationship converts part of that lost velocity pressure back into static pressure — the regain : V P = ( V 4005 ) 2 VP = \left(\frac{V}{4005}\right)^2 V P = ( 4005 V ​ ) 2 Δ S P regain = R × ( V P upstream − V P downstream ) \Delta SP_{\text{regain}} = R \times (VP_{\text{upstream}} - VP_{\text{downstream}}) Δ S P regain ​ = R × ( V P upstream ​ − V P downstream ​ )

with the regain coefficient R R R commonly taken as 0.75 to 0.90 . Each downstream section is sized so the regain offsets the friction loss, leaving roughly equal static pressure at every takeoff . Static regain suits long, straight, higher-velocity mains; it produces oversized duct at the far end and is rarely justified on a small low-pressure job.

Velocity Reduction

The designer assigns a target velocity to each successive section, stepping down from the fan discharge to the last branch, and computes the pressure loss that results. It is quick, it is used for exhaust and return systems where noise criteria are looser, and it demands experience because nothing in the method guarantees balance.

3. Velocity Limits and Noise

Duct-generated noise scales roughly with the fifth power of velocity, so velocity control is acoustic control.

  • Duct Section Private Office / Classroom / Church Retail / Restaurant / General Commercial
  • Supply main from unit 1,000 – 1,300 FPM 1,300 – 2,000 FPM
  • Supply branch 600 – 900 FPM 800 – 1,200 FPM
  • Runout to diffuser 400 – 700 FPM 600 – 900 FPM
  • Return main 800 – 1,200 FPM 1,000 – 1,500 FPM
  • Return grille face 300 – 500 FPM 400 – 600 FPM
  • Outdoor air intake louver 400 – 600 FPM (rain carry-over limit) 400 – 600 FPM

A sanctuary duct sized at the retail velocity will pass the airflow test and fail the occupants.

Round, Rectangular and Aspect Ratio

Equal-friction charts are drawn for round duct. Rectangular duct is converted through the equivalent round diameter : D e = 1.30 × ( a b ) 0.625 ( a + b ) 0.250 D_e = 1.30 \times \frac{(ab)^{0.625}}{(a+b)^{0.250}} D e ​ = 1.30 × ( a + b ) 0.250 ( ab ) 0.625 ​

Aspect ratio is the cost driver. A 24 × 12 24 \times 12 24 × 12 duct (2:1) and a 36 × 8 36 \times 8 36 × 8 duct (4.5:1) can carry the same air at the same friction rate, but the 4.5:1 duct uses noticeably more metal, more reinforcement and more insulation, and it loses more heat per CFM delivered. Keep aspect ratio at or below 4:1 wherever the ceiling cavity allows , and prefer round or flat-oval where it fits.

4. Fittings, Equivalent Length and System Effect

Fitting losses are expressed either as a loss coefficient C C C applied to velocity pressure, or converted to equivalent length of straight duct for the equal-friction method: Δ P fitting = C × V P \Delta P_{\text{fitting}} = C \times VP Δ P fitting ​ = C × V P

  • Fitting Typical Behaviour
  • Smooth radius elbow, R / W = 1.5 R/W = 1.5 R / W = 1.5 Lowest loss of the practical elbows
  • Radius elbow, R / W = 0.75 R/W = 0.75 R / W = 0.75 Roughly double the loss of the 1.5 radius
  • Square elbow with turning vanes Acceptable where space forbids a radius elbow
  • Square elbow without vanes The single most expensive common fitting — avoid
  • Conical or 45° entry branch takeoff Far lower loss than a straight 90° tap
  • Abrupt transition Creates separation and regenerated noise; use gradual slopes
  • System Effect — the Loss No One Measures

System effect is the pressure penalty produced when the airflow entering or leaving the fan is disturbed. A fan is rated on a test stand with uniform inlet flow and a long straight discharge; neither exists in a rooftop curb.

Common causes: an elbow immediately at the fan inlet, a duct turn within the fan's discharge "blow-through" length, an inlet closer to a wall than the manufacturer's minimum, and swirl in the inlet box.

System effect is a real pressure loss that must be added to the calculated system loss before selecting the fan .

It does not show up as a discrete reading on the balancer's manometer — it appears as a fan that delivers less air than its curve predicts, at a higher measured total external static pressure than the design.

The cure is layout, not speed: provide the manufacturer's straight duct length at inlet and discharge, use turning vanes where a close elbow is unavoidable, and never dump a fan discharge straight into a mitred turn.

5. Worked Example — Sizing a Low-Pressure Commercial Main

A packaged rooftop unit delivers 4,000 CFM with 1.00 in. w.g. of available external static pressure. Component losses: wet cooling coil 0.28, MERV 13 filter 0.30, supply diffusers 0.05, return grille 0.03, economizer/outdoor air section 0.10. The longest supply run has a TEL of 210 ft and the return TEL of 90 ft .

Step 1 — Available Static Pressure for the duct A S P = 1.00 − ( 0.28 + 0.30 + 0.05 + 0.03 + 0.10 ) = 1.00 − 0.76 = 0.24 in. w.g. ASP = 1.00 - (0.28 + 0.30 + 0.05 + 0.03 + 0.10) = 1.00 - 0.76 = 0.24\text{ in. w.g.} A SP = 1.00 − ( 0.28 + 0.30 + 0.05 + 0.03 + 0.10 ) = 1.00 − 0.76 = 0.24 in. w.g.

Step 2 — Total Effective Length T E L = 210 + 90 = 300 ft TEL = 210 + 90 = 300\text{ ft} TE L = 210 + 90 = 300 ft

Step 3 — Friction Rate F R = 0.24 × 100 300 = 0.08 in. w.g. per 100 ft FR = \frac{0.24 \times 100}{300} = 0.08\text{ in. w.g. per 100 ft} FR = 300 0.24 × 100 ​ = 0.08 in. w.g. per 100 ft

Step 4 — Size the trunk. On the duct slide rule, 4,000 CFM at a friction rate of 0.08 gives roughly a 22-inch round equivalent at about 1,500 FPM . Converting to rectangular at a 2:1 aspect ratio yields approximately 24 in. × 14 in.

Step 5 — Sanity check the velocity. 1,500 FPM in the main is acceptable for retail or general commercial, but it is at the top of the range for a classroom or worship space; there, the trunk would be enlarged to bring the velocity nearer 1,200 FPM even though the friction rate then falls below 0.08.

Step 6 — Add system effect. If the rooftop discharge turns 90° within two duct diameters, add the manufacturer's system-effect allowance to the 1.00 in. w.g. requirement before confirming the unit selection — otherwise the installed system will move perhaps 3,400 CFM rather than 4,000.

Loading diagram... Manual Q Low-Pressure Commercial Duct Design Sequence