Study guide
5.2 Fenestration, Opaque Envelope & Internal Heat Gains
North Carolina HVAC Contractor License Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: North Carolina HVAC Licensing Framework & Board Jurisprudence
1.1 NC Dual-Board Regulatory Structure & General Statutes 1.2 Heating Classifications, Groups & Scopes 1.3 Examination Prerequisites, Qualifier Responsibilities & Disciplinary Rules 1.4 Examination Logistics, Reference Books & Code Editions
2 Chapter 2: North Carolina Business Organizations, Contracts & Lien Law
2.1 Construction Contracts, Project Management & Bidding 2.2 North Carolina Mechanics' Lien Law & Bond Claims 2.3 Business Organizations, Financial Management & Taxation
3 Chapter 3: Construction Safety, Electrical Safety & EPA 608
3.1 OSHA 1926 Construction Safety & Job Site Protocols 3.2 Electrical Safety, NFPA 70E & Lockout/Tagout (LOTO) 3.3 EPA Section 608 & Refrigerant Transition Regulations
4 Chapter 4: Thermodynamics, Refrigeration Cycle & Psychrometrics
4.1 Fundamentals of Thermodynamics & Heat Transfer 4.2 The Mechanical Refrigeration Cycle & Component Dynamics 4.3 Psychrometric Properties, Air Processes & Chart Navigation
5 Chapter 5: ACCA Manual J & Manual N Load Calculations
5.1 Manual J Design Conditions & Thermal Parameters 5.2 Fenestration, Opaque Envelope & Internal Heat Gains 5.3 Infiltration, Duct Losses & Total Block Load Synthesis 5.4 ACCA Manual N Commercial Load Calculation
6 Chapter 6: ACCA Manual D & Manual Q Duct Design & Air Distribution
6.1 Fan Laws, Airflow Dynamics & Total External Static Pressure 6.2 ACCA Manual D Sizing Protocol & Friction Rate Calculation 6.3 SMACNA Duct Construction, Fittings & Air Balancing 6.4 ACCA Manual Q Commercial Low-Pressure Duct Design
7 Chapter 7: Forced Air Heating, Gas Furnaces & Fuel Piping
7.1 Natural Gas & Propane Combustion Fundamentals 7.2 Gas Furnace Operation, Sequence of Control & Diagnostics 7.3 Fuel Oil Heating Systems & Code-Compliant Fuel Gas Piping
8 Chapter 8: Heat Pumps, Inverters & Commercial System Selection (Manual CS)
8.1 Heat Pump Operating Principles, Reversing Valves & Physics 8.2 Defrost Controls, Supplemental Electric Heat & Balance Points 8.3 Inverter Mini-Splits & Variable Refrigerant Flow (VRF) Systems 8.4 Manual CS: Commercial Applications, Systems & Equipment
9 Chapter 9: Hydronic Heating, Steam Systems & Boilers (H1)
9.1 Hydronic Fundamentals, Boiler Classifications & Steam Systems 9.2 Hydronic Piping Layouts, Circulator Pumps & Head Loss Calculations 9.3 Boiler Trim, Expansion Tanks, Air Elimination & Safety Controls 9.4 The NC Uniform Boiler & Pressure Vessel Act (H1 Reference)
10 Chapter 10: Commercial Refrigeration & NC Board Regulations
10.1 NC State Board of Refrigeration Contractors Statutes & Licensure 10.2 Commercial Refrigeration Systems, Multiplex Racks & Defrost Protocols 10.3 Walk-In Coolers, Freezers, Evaporator Pressure Regulators & Valves
11 Chapter 11: NC Administration, Mechanical, Fuel Gas & Energy Codes
11.1 North Carolina Mechanical Code: Equipment Access, Clearances & Condensate 11.2 Ventilation Rates, Exhaust Systems & Duct Smoke Detection 11.3 NC Fuel Gas Code: Combustion Air, Venting & Gas Appliance Installation 11.4 NC Energy Conservation Code: Duct Testing, Envelope & Efficiency Standards 11.5 NC Administrative Code & Policies: Permits, Inspections & Plan Review
12 Chapter 12: Electrical Fundamentals, Motor Controls & Diagnostics
12.1 HVAC Electrical Fundamentals, Circuit Schematics & Power Distribution 12.2 Electric Motors, Capacitors & Motor Controls 12.3 Systematic HVAC Diagnostics, Superheat/Subcooling & Airflow Troubleshooting 12.4 System Commissioning, Testing, Adjusting & Balancing (TAB)
5.2 Fenestration, Opaque Envelope & Internal Heat Gains
Key Takeaways Explain This Topic AI
Fenestration cooling loads comprise conductive heat transmission and direct/diffuse solar radiant heat gain governed by the Solar Heat Gain Coefficient (SHGC) and orientation-specific Solar Load Factors (SLF).
North Carolina Energy Conservation Code (Table R402.1.2) mandates high-efficiency fenestration with maximum U-factors of 0.30 to 0.32 and a maximum SHGC of 0.25 across Climate Zones 3 and 4.
Opaque envelope cooling loads through walls and roofs incorporate sol-air temperature dynamics and thermal lag, calculated via Cooling Load Temperature Differences (CLTD) or Heat Transfer Multipliers (HTM).
Slab-on-grade foundation heat loss occurs primarily along the exposed exterior perimeter edge, calculated using the perimeter heat loss coefficient F_p (q = F_p × P × ΔT) rather than total surface area.
Internal heat gains are divided into sensible and latent components, with Manual J standardizing occupant loads at 230 BTU/h sensible and 200 BTU/h latent per person for N_bedrooms + 1 occupants, plus 1,200 BTU/h sensible for kitchen appliances.
Last updated: August 2026
Fenestration, Opaque Envelope & Internal Heat Gains
Core Principle: Peak residential heat gain consists of external envelope loads (solar radiant gain, fenestration conduction, opaque wall/roof conduction, and foundation heat transfer) combined with internal gains (occupants, lighting, plug loads, and appliances). Each component must be separated into sensible heat (which raises dry-bulb temperature) and latent heat (which adds airborne moisture).
Fenestration Heat Transfer (Windows, Glazed Doors & Skylights)
Fenestration is the most critical dynamic thermal component in residential load calculation. Glazed surfaces transmit heat through two concurrent mechanisms:
Conductive / Convective Heat Transmission ( q cond q_{\text{cond}} q cond ): q cond = U window × A window × Δ T q_{\text{cond}} = U_{\text{window}} \times A_{\text{window}} \times \Delta T q cond = U window × A window × Δ T
Solar Radiation Heat Gain ( q solar q_{\text{solar}} q solar ): q solar = A window × SHGC × SLF × IAC q_{\text{solar}} = A_{\text{window}} \times \text{SHGC} \times \text{SLF} \times \text{IAC} q solar = A window × SHGC × SLF × IAC
SHGC \text{SHGC} SHGC (Solar Heat Gain Coefficient): The fraction of incident solar radiation admitted through a window, both directly transmitted and absorbed and released inward. Ranges from 0.0 0.0 0.0 to 1.0 1.0 1.0 (lower values mean less solar heat gain).
SLF \text{SLF} SLF (Solar Load Factor): The peak solar irradiance value ( BTU / ( hr ⋅ ft 2 ) \text{BTU}/(\text{hr}\cdot\text{ft}^2) BTU / ( hr ⋅ ft 2 ) ) from Manual J Table 3, which varies by compass orientation (North, South, East, West, NE, NW, SE, SW), latitude, and month.
IAC \text{IAC} IAC (Internal Appurtenance Coefficient): A multiplier accounting for internal shading devices (such as light-colored horizontal blinds, blackout drapes, or solar screens, typically 0.45 − 0.85 0.45 - 0.85 0.45 − 0.85 ).
North Carolina Energy Conservation Code Fenestration Mandates
Under NCECC Table R402.1.2 , replacement and new residential fenestration must satisfy strict prescriptive thermal thresholds:
Climate Zone Geographic Scope in NC Maximum Fenestration U U U -Factor Maximum Fenestration SHGC \text{SHGC} SHGC Maximum Skylight U U U -Factor
Zone 3A Coastal Plains & Southern Sandhills 0.32 BTU / ( hr ⋅ ft 2 ⋅ ∘ F ) 0.32\text{ BTU}/(\text{hr}\cdot\text{ft}^2\cdot^\circ\text{F}) 0.32 BTU / ( hr ⋅ ft 2 ⋅ ∘ F ) 0.25 0.25 0.25 0.55 BTU / ( hr ⋅ ft 2 ⋅ ∘ F ) 0.55\text{ BTU}/(\text{hr}\cdot\text{ft}^2\cdot^\circ\text{F}) 0.55 BTU / ( hr ⋅ ft 2 ⋅ ∘ F )
Zone 4A Piedmont & Central Foothills 0.30 BTU / ( hr ⋅ ft 2 ⋅ ∘ F ) 0.30\text{ BTU}/(\text{hr}\cdot\text{ft}^2\cdot^\circ\text{F}) 0.30 BTU / ( hr ⋅ ft 2 ⋅ ∘ F ) 0.25 0.25 0.25 0.55 BTU / ( hr ⋅ ft 2 ⋅ ∘ F ) 0.55\text{ BTU}/(\text{hr}\cdot\text{ft}^2\cdot^\circ\text{F}) 0.55 BTU / ( hr ⋅ ft 2 ⋅ ∘ F )
Zone 5A Mountain Counties (e.g., Watauga, Avery) 0.30 BTU / ( hr ⋅ ft 2 ⋅ ∘ F ) 0.30\text{ BTU}/(\text{hr}\cdot\text{ft}^2\cdot^\circ\text{F}) 0.30 BTU / ( hr ⋅ ft 2 ⋅ ∘ F ) Not Regulated ( NR \text{NR} NR ) 0.55 BTU / ( hr ⋅ ft 2 ⋅ ∘ F ) 0.55\text{ BTU}/(\text{hr}\cdot\text{ft}^2\cdot^\circ\text{F}) 0.55 BTU / ( hr ⋅ ft 2 ⋅ ∘ F )
Impact of Window Orientation on Peak Cooling Loads
Solar heat gain varies dramatically depending on window orientation:
East-Facing Windows: Experience peak solar radiation in the early morning ( 8 : 00 AM − 10 : 00 AM 8:00\text{ AM} - 10:00\text{ AM} 8 : 00 AM − 10 : 00 AM ) when outdoor dry-bulb temperatures are relatively low.
West-Facing Windows: Experience peak solar radiation in the late afternoon ( 3 : 00 PM − 5 : 00 PM 3:00\text{ PM} - 5:00\text{ PM} 3 : 00 PM − 5 : 00 PM ) which coincides exactly with the daily maximum outdoor dry-bulb temperature, creating the highest combined cooling load spikes in North Carolina homes.
South-Facing Windows: Experience high solar angles in summer (causing lower direct gain if shaded by modest overhangs) but low solar angles in winter (providing beneficial passive solar heating).
North-Facing Windows: Receive almost exclusively diffuse ambient sky radiation with minimal direct solar beam irradiance.
- Opaque Envelope Components: Walls, Roofs & Sol-Air Effects
- Sol-Air Temperature & Cooling Load Temperature Difference (CLTD)
Sunlight striking opaque exterior surfaces (dark asphalt shingles, dark brick, fiber cement siding) heats the surface far above the ambient outdoor dry-bulb air temperature. This combined convective and radiant effect is defined as the sol-air temperature ( T sol-air T_{\text{sol-air}} T sol-air ).
In Manual J, this is simplified through Cooling Load Temperature Differences (CLTD) or direct Heat Transfer Multipliers (HTM) : q = U × A × CLTD or q = A × HTM q = U \times A \times \text{CLTD} \quad \text{or} \quad q = A \times \text{HTM} q = U × A × CLTD or q = A × HTM
Attic / Ceiling Dynamics: An unconditioned attic under dark asphalt shingles in a North Carolina summer can reach temperatures of 130 ∘ F − 140 ∘ F 130^\circ\text{F} - 140^\circ\text{F} 13 0 ∘ F − 14 0 ∘ F . With R − 38 R-38 R − 38 ceiling insulation, the temperature difference driving heat down into the living space is Δ T = 130 ∘ F − 75 ∘ F = 55 ∘ F \Delta T = 130^\circ\text{F} - 75^\circ\text{F} = 55^\circ\text{F} Δ T = 13 0 ∘ F − 7 5 ∘ F = 5 5 ∘ F , compared to an outdoor ambient Δ T \Delta T Δ T of only 17 ∘ F 17^\circ\text{F} 1 7 ∘ F .
Radiant Barriers: Installing an approved radiant barrier (emittance ϵ ≤ 0.05 \epsilon \le 0.05 ϵ ≤ 0.05 ) under the roof decking reduces radiant transfer from the hot roof deck to the top of ceiling insulation, lowering attic air temperatures by 15 ∘ F − 25 ∘ F 15^\circ\text{F} - 25^\circ\text{F} 1 5 ∘ F − 2 5 ∘ F and reducing ceiling cooling loads.
Foundation Heat Losses: Slabs, Basements & Crawlspaces
Foundations interact with the earth, which has substantial thermal mass. Heat loss is not modeled by simple one-dimensional outdoor Δ T \Delta T Δ T .
1. Slab-on-Grade Floors
In slab-on-grade construction, downward heat loss through the center of the concrete slab is minimal because the ground underneath stabilizes near deep-ground temperature ( 55 ∘ F − 60 ∘ F 55^\circ\text{F} - 60^\circ\text{F} 5 5 ∘ F − 6 0 ∘ F ). Almost all heat loss occurs laterally through the exposed perimeter edge to ambient winter air.
Manual J calculates slab design heating loss using the slab perimeter formula : q slab = F p × P × ( T indoor − T outdoor, heat ) q_{\text{slab}} = F_p \times P \times (T_{\text{indoor}} - T_{\text{outdoor, heat}}) q slab = F p × P × ( T indoor − T outdoor, heat )
where:
F p F_p F p = Slab perimeter heat loss coefficient ( BTU / ( hr ⋅ linear ft ⋅ ∘ F ) \text{BTU}/(\text{hr}\cdot\text{linear ft}\cdot^\circ\text{F}) BTU / ( hr ⋅ linear ft ⋅ ∘ F ) ).
P P P = Length of the exposed exterior slab perimeter (linear feet).
Δ T = 70 ∘ F − T outdoor, heat \Delta T = 70^\circ\text{F} - T_{\text{outdoor, heat}} Δ T = 7 0 ∘ F − T outdoor, heat .
Slab Edge Insulation Configuration F p F_p F p Coefficient (Climate Zone 4)
Uninsulated Slab Edge 0.86 BTU / ( hr ⋅ ft ⋅ ∘ F ) 0.86\text{ BTU}/(\text{hr}\cdot\text{ft}\cdot^\circ\text{F}) 0.86 BTU / ( hr ⋅ ft ⋅ ∘ F )
R − 5 R-5 R − 5 Vertical Edge Insulation ( 24 " 24" 24" depth) 0.54 BTU / ( hr ⋅ ft ⋅ ∘ F ) 0.54\text{ BTU}/(\text{hr}\cdot\text{ft}\cdot^\circ\text{F}) 0.54 BTU / ( hr ⋅ ft ⋅ ∘ F )
R − 10 R-10 R − 10 Vertical Edge Insulation ( 24 " 24" 24" depth) 0.38 BTU / ( hr ⋅ ft ⋅ ∘ F ) 0.38\text{ BTU}/(\text{hr}\cdot\text{ft}\cdot^\circ\text{F}) 0.38 BTU / ( hr ⋅ ft ⋅ ∘ F )
2. Vented Crawlspaces vs. Closed (Conditioned) Crawlspaces
North Carolina homes feature two distinct crawlspace configurations:
Vented Crawlspaces: Open foundation vents expose the subfloor to outdoor ambient temperatures and humid summer air. The floor above must be insulated to R − 19 R-19 R − 19 (Zone 4) or R − 13 R-13 R − 13 (Zone 3). In summer, hot humid air entering through vents condenses on cold ductwork and floor joists, creating severe moisture problems.
Closed / Conditioned Crawlspaces (NCRC Section R408.3 & Appendix E): Vents are completely eliminated. The ground is covered with a continuous, sealed minimum 6 mil 6\text{ mil} 6 mil (or 10 mil 10\text{ mil} 10 mil ) vapor retarder turned up 6 " 6" 6" on foundation walls. Foundation perimeter walls are insulated with R − 10 R-10 R − 10 continuous rigid foam or R − 13 R-13 R − 13 cavity insulation . The crawlspace is conditioned with either supply air ( 1 CFM 1\text{ CFM} 1 CFM per 50 sq ft 50\text{ sq ft} 50 sq ft of crawlspace area) or a dedicated crawlspace dehumidifier. The living space floor requires no subfloor insulation , and floor heat loss is virtually eliminated.
Internal Heat Gains (Sensible & Latent)
Internal heat gains originate from people, appliances, and lighting inside the conditioned envelope. These gains increase cooling loads and are credited in full during summer, but are generally excluded from heating load calculations to ensure heating systems can warm the structure when unoccupied.
1. Occupant Heat Gains (Manual J Bedroom Rule)
Manual J standardizes residential occupant allowances based on the physical capacity of the home: Design Occupants = N bedrooms + 1 \text{Design Occupants} = N_{\text{bedrooms}} + 1 Design Occupants = N bedrooms + 1
(Example: A 3-bedroom home is designed for 3 + 1 = 4 3 + 1 = 4 3 + 1 = 4 occupants; a 4-bedroom home is designed for 4 + 1 = 5 4 + 1 = 5 4 + 1 = 5 occupants).
Heat generated per sedentary occupant:
- Sensible Heat: 230 BTU/h 230\text{ BTU/h} 230 BTU/h per person
- Latent Heat: 200 BTU/h 200\text{ BTU/h} 200 BTU/h per person
- Total Heat: 430 BTU/h 430\text{ BTU/h} 430 BTU/h per person
- 2. Appliance & Plug Load Allowances
Standard Kitchen Appliance Baseline: 1,200 BTU/h sensible 1{,}200\text{ BTU/h sensible} 1 , 200 BTU/h sensible and 0 BTU/h latent 0\text{ BTU/h latent} 0 BTU/h latent (assumes range hood exhaust fan discharges cooking moisture outdoors).
Additional Kitchen / Bar Refrigerators: 400 BTU/h 400\text{ BTU/h} 400 BTU/h sensible each.
Home Electronics & Computers: Actual rated wattage × 3.412 BTU/h per Watt \times 3.412\text{ BTU/h per Watt} × 3.412 BTU/h per Watt (or default Manual J allowances of 400 − 800 BTU/h 400 - 800\text{ BTU/h} 400 − 800 BTU/h for home office equipment).
3. Lighting Heat Gains
Lighting generates purely sensible heat: q lighting = Total Watts × 3.412 BTU/h per Watt q_{\text{lighting}} = \text{Total Watts} \times 3.412\text{ BTU/h per Watt} q lighting = Total Watts × 3.412 BTU/h per Watt
Under modern energy codes utilizing high-efficacy LED lighting, standard Manual J residential lighting allowance is typically 0.80 BTU / ( hr ⋅ sq ft ) 0.80\text{ BTU}/(\text{hr}\cdot\text{sq ft}) 0.80 BTU / ( hr ⋅ sq ft ) or based on actual connected fixtures.
- Comprehensive Worked Example: Envelope & Internal Cooling Load
- Problem Data (Living Room in Raleigh, NC)
South-Facing Window: Area 60 sq ft 60\text{ sq ft} 60 sq ft , U = 0.30 U = 0.30 U = 0.30 , SHGC = 0.25 \text{SHGC} = 0.25 SHGC = 0.25 , SLF = 45 BTU / ( hr ⋅ ft 2 ) \text{SLF} = 45\text{ BTU}/(\text{hr}\cdot\text{ft}^2) SLF = 45 BTU / ( hr ⋅ ft 2 ) , IAC = 0.70 \text{IAC} = 0.70 IAC = 0.70 , Δ T = 17 ∘ F \Delta T = 17^\circ\text{F} Δ T = 1 7 ∘ F .
West-Facing Window: Area 40 sq ft 40\text{ sq ft} 40 sq ft , U = 0.30 U = 0.30 U = 0.30 , SHGC = 0.25 \text{SHGC} = 0.25 SHGC = 0.25 , SLF = 150 BTU / ( hr ⋅ ft 2 ) \text{SLF} = 150\text{ BTU}/(\text{hr}\cdot\text{ft}^2) SLF = 150 BTU / ( hr ⋅ ft 2 ) , IAC = 0.70 \text{IAC} = 0.70 IAC = 0.70 , Δ T = 17 ∘ F \Delta T = 17^\circ\text{F} Δ T = 1 7 ∘ F .
Occupants: 4 people in living zone.
Lighting & Electronics: 300 Watts 300\text{ Watts} 300 Watts LED lighting and TV.
Step 1: Fenestration Conduction Heat Gain q cond, south = 0.30 × 60 sq ft × 17 ∘ F = 306 BTU/h q_{\text{cond, south}} = 0.30 \times 60\text{ sq ft} \times 17^\circ\text{F} = 306\text{ BTU/h} q cond, south = 0.30 × 60 sq ft × 1 7 ∘ F = 306 BTU/h q cond, west = 0.30 × 40 sq ft × 17 ∘ F = 204 BTU/h q_{\text{cond, west}} = 0.30 \times 40\text{ sq ft} \times 17^\circ\text{F} = 204\text{ BTU/h} q cond, west = 0.30 × 40 sq ft × 1 7 ∘ F = 204 BTU/h Total Fenestration Conduction = 306 + 204 = 510 BTU/h \text{Total Fenestration Conduction} = 306 + 204 = 510\text{ BTU/h} Total Fenestration Conduction = 306 + 204 = 510 BTU/h
Step 2: Fenestration Solar Radiant Heat Gain q solar, south = 60 sq ft × 0.25 × 45 × 0.70 = 472.5 BTU/h q_{\text{solar, south}} = 60\text{ sq ft} \times 0.25 \times 45 \times 0.70 = 472.5\text{ BTU/h} q solar, south = 60 sq ft × 0.25 × 45 × 0.70 = 472.5 BTU/h q solar, west = 40 sq ft × 0.25 × 150 × 0.70 = 1,050.0 BTU/h q_{\text{solar, west}} = 40\text{ sq ft} \times 0.25 \times 150 \times 0.70 = 1{,}050.0\text{ BTU/h} q solar, west = 40 sq ft × 0.25 × 150 × 0.70 = 1 , 050.0 BTU/h Total Fenestration Solar Gain = 472.5 + 1,050.0 = 1,522.5 BTU/h \text{Total Fenestration Solar Gain} = 472.5 + 1{,}050.0 = 1{,}522.5\text{ BTU/h} Total Fenestration Solar Gain = 472.5 + 1 , 050.0 = 1 , 522.5 BTU/h
(Note how the smaller 40 sq ft 40\text{ sq ft} 40 sq ft west window delivers more than double the solar heat of the 60 sq ft 60\text{ sq ft} 60 sq ft south window due to afternoon peak irradiance).
Step 3: Occupant Heat Gain (4 People) q sensible, people = 4 × 230 BTU/h = 920 BTU/h q_{\text{sensible, people}} = 4 \times 230\text{ BTU/h} = 920\text{ BTU/h} q sensible, people = 4 × 230 BTU/h = 920 BTU/h q latent, people = 4 × 200 BTU/h = 800 BTU/h q_{\text{latent, people}} = 4 \times 200\text{ BTU/h} = 800\text{ BTU/h} q latent, people = 4 × 200 BTU/h = 800 BTU/h
Step 4: Lighting and Equipment Heat Gain q sensible, equipment = 300 W × 3.412 BTU/(hr ⋅ W) = 1,023.6 BTU/h q_{\text{sensible, equipment}} = 300\text{ W} \times 3.412\text{ BTU/(hr}\cdot\text{W)} = 1{,}023.6\text{ BTU/h} q sensible, equipment = 300 W × 3.412 BTU/(hr ⋅ W) = 1 , 023.6 BTU/h
Step 5: Subtotal Living Room Heat Gains
Total Sensible Gain: 510 + 1,522.5 + 920 + 1,023.6 = 3,976.1 BTU/h 510 + 1{,}522.5 + 920 + 1{,}023.6 = 3{,}976.1\text{ BTU/h} 510 + 1 , 522.5 + 920 + 1 , 023.6 = 3 , 976.1 BTU/h
Total Latent Gain: 800 BTU/h 800\text{ BTU/h} 800 BTU/h
Total Combined Load: 3,976.1 + 800 = 4,776.1 BTU/h 3{,}976.1 + 800 = 4{,}776.1\text{ BTU/h} 3 , 976.1 + 800 = 4 , 776.1 BTU/h