Study guide

5.1 Manual J Design Conditions & Thermal Parameters

North Carolina HVAC Contractor License Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: North Carolina HVAC Licensing Framework & Board Jurisprudence

1.1 NC Dual-Board Regulatory Structure & General Statutes 1.2 Heating Classifications, Groups & Scopes 1.3 Examination Prerequisites, Qualifier Responsibilities & Disciplinary Rules 1.4 Examination Logistics, Reference Books & Code Editions

2 Chapter 2: North Carolina Business Organizations, Contracts & Lien Law

2.1 Construction Contracts, Project Management & Bidding 2.2 North Carolina Mechanics' Lien Law & Bond Claims 2.3 Business Organizations, Financial Management & Taxation

3 Chapter 3: Construction Safety, Electrical Safety & EPA 608

3.1 OSHA 1926 Construction Safety & Job Site Protocols 3.2 Electrical Safety, NFPA 70E & Lockout/Tagout (LOTO) 3.3 EPA Section 608 & Refrigerant Transition Regulations

4 Chapter 4: Thermodynamics, Refrigeration Cycle & Psychrometrics

4.1 Fundamentals of Thermodynamics & Heat Transfer 4.2 The Mechanical Refrigeration Cycle & Component Dynamics 4.3 Psychrometric Properties, Air Processes & Chart Navigation

5 Chapter 5: ACCA Manual J & Manual N Load Calculations

5.1 Manual J Design Conditions & Thermal Parameters 5.2 Fenestration, Opaque Envelope & Internal Heat Gains 5.3 Infiltration, Duct Losses & Total Block Load Synthesis 5.4 ACCA Manual N Commercial Load Calculation

6 Chapter 6: ACCA Manual D & Manual Q Duct Design & Air Distribution

6.1 Fan Laws, Airflow Dynamics & Total External Static Pressure 6.2 ACCA Manual D Sizing Protocol & Friction Rate Calculation 6.3 SMACNA Duct Construction, Fittings & Air Balancing 6.4 ACCA Manual Q Commercial Low-Pressure Duct Design

7 Chapter 7: Forced Air Heating, Gas Furnaces & Fuel Piping

7.1 Natural Gas & Propane Combustion Fundamentals 7.2 Gas Furnace Operation, Sequence of Control & Diagnostics 7.3 Fuel Oil Heating Systems & Code-Compliant Fuel Gas Piping

8 Chapter 8: Heat Pumps, Inverters & Commercial System Selection (Manual CS)

8.1 Heat Pump Operating Principles, Reversing Valves & Physics 8.2 Defrost Controls, Supplemental Electric Heat & Balance Points 8.3 Inverter Mini-Splits & Variable Refrigerant Flow (VRF) Systems 8.4 Manual CS: Commercial Applications, Systems & Equipment

9 Chapter 9: Hydronic Heating, Steam Systems & Boilers (H1)

9.1 Hydronic Fundamentals, Boiler Classifications & Steam Systems 9.2 Hydronic Piping Layouts, Circulator Pumps & Head Loss Calculations 9.3 Boiler Trim, Expansion Tanks, Air Elimination & Safety Controls 9.4 The NC Uniform Boiler & Pressure Vessel Act (H1 Reference)

10 Chapter 10: Commercial Refrigeration & NC Board Regulations

10.1 NC State Board of Refrigeration Contractors Statutes & Licensure 10.2 Commercial Refrigeration Systems, Multiplex Racks & Defrost Protocols 10.3 Walk-In Coolers, Freezers, Evaporator Pressure Regulators & Valves

11 Chapter 11: NC Administration, Mechanical, Fuel Gas & Energy Codes

11.1 North Carolina Mechanical Code: Equipment Access, Clearances & Condensate 11.2 Ventilation Rates, Exhaust Systems & Duct Smoke Detection 11.3 NC Fuel Gas Code: Combustion Air, Venting & Gas Appliance Installation 11.4 NC Energy Conservation Code: Duct Testing, Envelope & Efficiency Standards 11.5 NC Administrative Code & Policies: Permits, Inspections & Plan Review

12 Chapter 12: Electrical Fundamentals, Motor Controls & Diagnostics

12.1 HVAC Electrical Fundamentals, Circuit Schematics & Power Distribution 12.2 Electric Motors, Capacitors & Motor Controls 12.3 Systematic HVAC Diagnostics, Superheat/Subcooling & Airflow Troubleshooting 12.4 System Commissioning, Testing, Adjusting & Balancing (TAB)

5.1 Manual J Design Conditions & Thermal Parameters

Key Takeaways Explain This Topic AI

ACCA Manual J (8th Edition) is the ANSI-recognized standard mandated by the North Carolina Residential Code (NCRC Section M1401.3) and North Carolina Energy Conservation Code for calculating residential heating and cooling design loads.

Outdoor design temperatures across North Carolina vary substantially by climate region, utilizing the 99% heating dry-bulb design temperature (19°F to 22°F in the mountains, 22°F to 24°F in the Piedmont, and 28°F to 30°F along the coast) and 1% cooling dry-bulb / coincident wet-bulb temperatures.

Standard indoor design conditions under Manual J and NC Energy Code are fixed at 70°F for heating and 75°F at 50% relative humidity for cooling, establishing the design temperature difference (ΔT) and humidity ratio difference (ΔW).

Conductive heat transfer through building assemblies is governed by Fourier's steady-state relationship q = U × A × ΔT, where the overall thermal transmittance (U-factor) is the mathematical inverse of the cumulative thermal resistance (U = 1 / R_total).

Parallel path framing factor calculations account for structural thermal bridging through studs, plates, and headers, significantly increasing assembly U-factors compared to nominal cavity insulation R-values.

Last updated: August 2026

Manual J Design Conditions & Thermal Parameters

Core Statutory Mandate: North Carolina Residential Code (NCRC) Section M1401.3 requires that heating and cooling equipment "be sized in accordance with ACCA Manual S or other approved sizing methodologies based on building loads calculated in accordance with ACCA Manual J or other approved heating and cooling calculation methodologies." NCECC Section R403.7 does not name the manuals — it simply directs that equipment be sized in accordance with the North Carolina Mechanical Code . The enforceable licensing mandate is 21 NCAC 50 .0505(e) , which requires a room-by-room load calculation for every newly installed residential structure , performed by a Board licensee or a NC Licensed Professional Engineer, with the sizing record retained six years . Traditional "rules of thumb" (500 or 600 square feet per ton) satisfy none of these.

Two North Carolina amendments worth memorizing: (1) NCRC M1401.3 permits multistage or variable-refrigerant-flow equipment to exceed the Manual S capacity limits where the loads fall within the manufacturer's published specifications, and permits the next larger standard size where no listed capacity satisfies the calculated gain; (2) North Carolina does not require Manual J/S/D calculation submittals or review as a condition of permitting, inspection, or a certificate of compliance or occupancy — but the Board still requires the licensee to have performed and retained the calculation.

The Purpose & Necessity of ACCA Manual J

Air Conditioning Contractors of America ( ACCA ) Manual J is the ANSI-accredited standard for determining sensible and latent heating and cooling loads for single-family residences, townhouses, and small multi-family structures.

Hazards of Rule-of-Thumb Sizing

When HVAC systems are sized using historical rules of thumb rather than detailed Manual J calculations, equipment is virtually always oversized . Oversizing leads to severe operational deficiencies:

Inadequate Dehumidification: Air conditioners and heat pumps remove latent moisture primarily during long, steady-state run cycles. An oversized unit rapidly pulls down sensible indoor temperature and satisfies the thermostat before the evaporator coil reaches its condensing temperature long enough to extract moisture, leading to high relative humidity (above 60%), clammy air, and biological growth (mold and dust mites).

Short-Cycling & Accelerated Wear: Frequent starts and stops increase electrical inrush current demands, stress compressor mechanical bearings, overheat start capacitors, and cause premature compressor and blower failure.

Temperature Stratification & Poor Air Distribution: Short run cycles fail to establish continuous air mixing, resulting in severe hot and cold spots between rooms and floors.

Elevated Operating Costs: Starting electrical draw ( L R A LRA L R A ) consumes significantly more energy per minute than steady-state operation ( R L A RLA R L A ), driving up electric utility bills. Consequences of Equipment Sizing Deficiencies

  • ├── Oversized System (Rule-of-Thumb)
  • │ ├── Rapid temperature pull-down -> Short-cycling
  • │ ├── Inadequate moisture removal -> Mold, mildew, >60% RH
  • │ └── High inrush amps -> Premature compressor failure
  • └── Accurately Sized System (ACCA Manual J / S)
  • ├── Long, continuous run cycles at peak design conditions
  • ├── Optimum latent dehumidification (45% - 50% RH)
  • └── Balanced room-by-room CFM distribution
  • North Carolina Climate Zones & Outdoor Design Temperatures

ACCA Manual J incorporates geographic weather data compiled by ASHRAE based on statistical 30-year meteorological distributions:

Winter 99% Design Dry-Bulb Temperature ( T db, outdoor T_{\text{db, outdoor}} T db, outdoor ​ ): The outdoor dry-bulb temperature that is equaled or exceeded for 99% of the hours in an average year (or conversely, the temperature drops below this value for only 1% of the annual hours, approximately 88 hours).

Summer 1% Design Dry-Bulb Temperature ( T db, outdoor T_{\text{db, outdoor}} T db, outdoor ​ ): The outdoor dry-bulb temperature that is exceeded for only 1% of the annual cooling hours (approximately 30 hours per summer).

Mean Coincident Wet-Bulb ( T mcwb T_{\text{mcwb}} T mcwb ​ ): The average wet-bulb temperature occurring simultaneously with the 1% summer dry-bulb design temperature.

Daily Range (DR): The difference between the average daily maximum and average daily minimum temperatures during the hottest month. Categorized as:

High ( D R > 25 ∘ F DR > 25^\circ\text{F} D R > 2 5 ∘ F ): Mountain regions (e.g., Asheville, Boone).

Medium ( 16 ∘ F ≤ D R ≤ 25 ∘ F 16^\circ\text{F} \le DR \le 25^\circ\text{F} 1 6 ∘ F ≤ D R ≤ 2 5 ∘ F ): Piedmont and central interior plains (e.g., Charlotte, Raleigh, Greensboro, Fayetteville).

Low ( D R < 16 ∘ F DR < 16^\circ\text{F} D R < 1 6 ∘ F ): Coastal barrier islands and immediate shoreline (e.g., Cape Hatteras, Wilmington, Morehead City).

North Carolina Geographic Design Conditions Table

Location / City Climate Zone Winter 99% DB ( ∘ F ^\circ\text{F} ∘ F ) Summer 1% DB ( ∘ F ^\circ\text{F} ∘ F ) Summer MCWB ( ∘ F ^\circ\text{F} ∘ F ) Daily Range (DR) Outdoor Grains ( W o W_o W o ​ ) @ 1%

Asheville Zone 4A / 5A 19 ∘ F 19^\circ\text{F} 1 9 ∘ F 86 ∘ F 86^\circ\text{F} 8 6 ∘ F 69 ∘ F 69^\circ\text{F} 6 9 ∘ F High ( 26 ∘ F 26^\circ\text{F} 2 6 ∘ F ) 97 grains/lb

Boone Zone 5A 14 ∘ F 14^\circ\text{F} 1 4 ∘ F 81 ∘ F 81^\circ\text{F} 8 1 ∘ F 66 ∘ F 66^\circ\text{F} 6 6 ∘ F High ( 25 ∘ F 25^\circ\text{F} 2 5 ∘ F ) 87 grains/lb

Charlotte Zone 4A 22 ∘ F 22^\circ\text{F} 2 2 ∘ F 92 ∘ F 92^\circ\text{F} 9 2 ∘ F 74 ∘ F 74^\circ\text{F} 7 4 ∘ F Medium ( 20 ∘ F 20^\circ\text{F} 2 0 ∘ F ) 114 grains/lb

Greensboro / Winston-Salem Zone 4A 21 ∘ F 21^\circ\text{F} 2 1 ∘ F 90 ∘ F 90^\circ\text{F} 9 0 ∘ F 74 ∘ F 74^\circ\text{F} 7 4 ∘ F Medium ( 19 ∘ F 19^\circ\text{F} 1 9 ∘ F ) 115 grains/lb

Raleigh-Durham Zone 4A 22 ∘ F 22^\circ\text{F} 2 2 ∘ F 92 ∘ F 92^\circ\text{F} 9 2 ∘ F 75 ∘ F 75^\circ\text{F} 7 5 ∘ F Medium ( 21 ∘ F 21^\circ\text{F} 2 1 ∘ F ) 118 grains/lb

Fayetteville Zone 4A / 3A 25 ∘ F 25^\circ\text{F} 2 5 ∘ F 94 ∘ F 94^\circ\text{F} 9 4 ∘ F 76 ∘ F 76^\circ\text{F} 7 6 ∘ F Medium ( 22 ∘ F 22^\circ\text{F} 2 2 ∘ F ) 123 grains/lb

Wilmington Zone 3A 28 ∘ F 28^\circ\text{F} 2 8 ∘ F 90 ∘ F 90^\circ\text{F} 9 0 ∘ F 77 ∘ F 77^\circ\text{F} 7 7 ∘ F Low-Med ( 16 ∘ F 16^\circ\text{F} 1 6 ∘ F ) 129 grains/lb

Morehead City / New Bern Zone 3A 27 ∘ F 27^\circ\text{F} 2 7 ∘ F 89 ∘ F 89^\circ\text{F} 8 9 ∘ F 77 ∘ F 77^\circ\text{F} 7 7 ∘ F Low-Med ( 15 ∘ F 15^\circ\text{F} 1 5 ∘ F ) 130 grains/lb

Cape Hatteras Zone 3A 32 ∘ F 32^\circ\text{F} 3 2 ∘ F 86 ∘ F 86^\circ\text{F} 8 6 ∘ F 77 ∘ F 77^\circ\text{F} 7 7 ∘ F Low ( 12 ∘ F 12^\circ\text{F} 1 2 ∘ F ) 131 grains/lb

Indoor Design Criteria & Thermal Differentials

Manual J standardizes indoor baseline comfort conditions to prevent arbitrary safety factors from skewing equipment sizing:

1. Indoor Temperature Setpoints

Winter Indoor Design Dry-Bulb ( T db, in, heat T_{\text{db, in, heat}} T db, in, heat ​ ): 70 ∘ F 70^\circ\text{F} 7 0 ∘ F ( 21.1 ∘ C 21.1^\circ\text{C} 21. 1 ∘ C ).

Summer Indoor Design Dry-Bulb ( T db, in, cool T_{\text{db, in, cool}} T db, in, cool ​ ): 75 ∘ F 75^\circ\text{F} 7 5 ∘ F ( 23.9 ∘ C 23.9^\circ\text{C} 23. 9 ∘ C ).

Summer Indoor Relative Humidity: 50 % 50\% 50% Relative Humidity ( R H RH R H ), corresponding to a 55 ∘ F 55^\circ\text{F} 5 5 ∘ F dew point temperature and an indoor moisture content of approximately 65 grains of moisture per pound of dry air 65\text{ grains of moisture per pound of dry air} 65 grains of moisture per pound of dry air ( W i ≈ 65 gr/lb W_i \approx 65\text{ gr/lb} W i ​ ≈ 65 gr/lb ). ( 1 lb of water = 7,000 grains 1\text{ lb of water} = 7{,}000\text{ grains} 1 lb of water = 7 , 000 grains ).

2. Design Temperature Differences

Heating Design Temperature Difference ( Δ T heat \Delta T_{\text{heat}} Δ T heat ​ ): Δ T heat = T db, in, heat − T db, out, 99% \Delta T_{\text{heat}} = T_{\text{db, in, heat}} - T_{\text{db, out, 99\%}} Δ T heat ​ = T db, in, heat ​ − T db, out, 99% ​

Example for Raleigh, NC: Δ T heat = 70 ∘ F − 22 ∘ F = 48 ∘ F \Delta T_{\text{heat}} = 70^\circ\text{F} - 22^\circ\text{F} = 48^\circ\text{F} Δ T heat ​ = 7 0 ∘ F − 2 2 ∘ F = 4 8 ∘ F

Cooling Design Temperature Difference ( Δ T cool \Delta T_{\text{cool}} Δ T cool ​ ): Δ T cool = T db, out, 1% − T db, in, cool \Delta T_{\text{cool}} = T_{\text{db, out, 1\%}} - T_{\text{db, in, cool}} Δ T cool ​ = T db, out, 1% ​ − T db, in, cool ​

Example for Raleigh, NC: Δ T cool = 92 ∘ F − 75 ∘ F = 17 ∘ F \Delta T_{\text{cool}} = 92^\circ\text{F} - 75^\circ\text{F} = 17^\circ\text{F} Δ T cool ​ = 9 2 ∘ F − 7 5 ∘ F = 1 7 ∘ F

Moisture Grains Difference ( Δ W \Delta W Δ W ): Δ W = W outdoor − W indoor \Delta W = W_{\text{outdoor}} - W_{\text{indoor}} Δ W = W outdoor ​ − W indoor ​

Example for Raleigh, NC ( W o = 118 gr/lb W_o = 118\text{ gr/lb} W o ​ = 118 gr/lb , W i = 65 gr/lb W_i = 65\text{ gr/lb} W i ​ = 65 gr/lb ): Δ W = 118 − 65 = 53 grains per pound of dry air \Delta W = 118 - 65 = 53\text{ grains per pound of dry air} Δ W = 118 − 65 = 53 grains per pound of dry air

Fundamentals of Building Heat Transfer Physics

Heat transfer through building assemblies occurs through three physical mechanisms:

Conduction: Direct molecular transfer of kinetic energy through solid structural materials (studs, insulation, drywall, brick, glass). Governed by Fourier's law: q = k × A × Δ T L q = \frac{k \times A \times \Delta T}{L} q = L k × A × Δ T ​ where k k k is thermal conductivity ( BTU ⋅ in / ( hr ⋅ ft 2 ⋅ ∘ F ) \text{BTU}\cdot\text{in}/(\text{hr}\cdot\text{ft}^2\cdot^\circ\text{F}) BTU ⋅ in / ( hr ⋅ ft 2 ⋅ ∘ F ) ), A A A is surface area ( ft 2 \text{ft}^2 ft 2 ), and L L L is material thickness ( inches \text{inches} inches ).

Convection: Heat transfer between a solid surface and an adjacent moving fluid (air). In building cavities and boundary surfaces, natural convective air currents wash across interior drywall and exterior sheathing, represented by air film surface resistances ( R i R_i R i ​ and R o R_o R o ​ ).

Radiation: Electromagnetic energy transfer between surfaces across transparent air spaces (such as solar radiant heat transmitted through window glazing or attic radiant transfer from hot roof decking to ceiling insulation).

  • Thermal Resistance ( R R R -Value) vs. Thermal Transmittance ( U U U -Factor)
  • Definitions & Mathematical Relationships

R R R -Value (Thermal Resistance): The measure of a material's resistance to conductive heat flow. Units are ( hr ⋅ ft 2 ⋅ ∘ F ) / BTU (\text{hr}\cdot\text{ft}^2\cdot^\circ\text{F})/\text{BTU} ( hr ⋅ ft 2 ⋅ ∘ F ) / BTU . Higher R R R -values indicate superior insulating capability.

U U U -Factor (Overall Heat Transfer Coefficient / Thermal Transmittance): The rate of steady-state heat flow through a unit area of a building assembly per unit temperature difference. Units are BTU / ( hr ⋅ ft 2 ⋅ ∘ F ) \text{BTU}/(\text{hr}\cdot\text{ft}^2\cdot^\circ\text{F}) BTU / ( hr ⋅ ft 2 ⋅ ∘ F ) . Lower U U U -factors indicate superior thermal performance. U = 1 R total ⟺ R total = 1 U U = \frac{1}{R_{\text{total}}} \quad \Longleftrightarrow \quad R_{\text{total}} = \frac{1}{U} U = R total ​ 1 ​ ⟺ R total ​ = U 1 ​

Series Resistance Summation

When a wall, ceiling, or floor consists of multiple homogeneous layers placed in series, the total thermal resistance is the direct algebraic sum of the individual component R R R -values, including inside and outside surface air films: R total = R inside film + R 1 + R 2 + R 3 + ⋯ + R n + R outside film R_{\text{total}} = R_{\text{inside film}} + R_1 + R_2 + R_3 + \dots + R_n + R_{\text{outside film}} R total ​ = R inside film ​ + R 1 ​ + R 2 ​ + R 3 ​ + ⋯ + R n ​ + R outside film ​

Surface Air Film Layer Winter Heating R R R -Value Summer Cooling R R R -Value

Inside Surface Film ( R i R_i R i ​ ) — Still air, vertical wall 0.68 hr ⋅ ft 2 ⋅ ∘ F / BTU 0.68\text{ hr}\cdot\text{ft}^2\cdot^\circ\text{F}/\text{BTU} 0.68 hr ⋅ ft 2 ⋅ ∘ F / BTU 0.68 hr ⋅ ft 2 ⋅ ∘ F / BTU 0.68\text{ hr}\cdot\text{ft}^2\cdot^\circ\text{F}/\text{BTU} 0.68 hr ⋅ ft 2 ⋅ ∘ F / BTU

Inside Surface Film ( R i R_i R i ​ ) — Still air, horizontal ceiling (heat up) 0.61 hr ⋅ ft 2 ⋅ ∘ F / BTU 0.61\text{ hr}\cdot\text{ft}^2\cdot^\circ\text{F}/\text{BTU} 0.61 hr ⋅ ft 2 ⋅ ∘ F / BTU 0.92 hr ⋅ ft 2 ⋅ ∘ F / BTU 0.92\text{ hr}\cdot\text{ft}^2\cdot^\circ\text{F}/\text{BTU} 0.92 hr ⋅ ft 2 ⋅ ∘ F / BTU (heat down)

Outside Surface Film ( R o R_o R o ​ ) — Moving air ( 15 mph 15\text{ mph} 15 mph wind in winter) 0.17 hr ⋅ ft 2 ⋅ ∘ F / BTU 0.17\text{ hr}\cdot\text{ft}^2\cdot^\circ\text{F}/\text{BTU} 0.17 hr ⋅ ft 2 ⋅ ∘ F / BTU —

Outside Surface Film ( R o R_o R o ​ ) — Moving air ( 7.5 mph 7.5\text{ mph} 7.5 mph wind in summer) — 0.25 hr ⋅ ft 2 ⋅ ∘ F / BTU 0.25\text{ hr}\cdot\text{ft}^2\cdot^\circ\text{F}/\text{BTU} 0.25 hr ⋅ ft 2 ⋅ ∘ F / BTU

Parallel Path Thermal Bridging & Framing Factors

Real-world building assemblies are not continuous layers of insulation. Structural framing (solid wood studs, plates, headers, and sill plates) interrupts cavity insulation, acting as a thermal bridge with a much lower R R R -value ( R ≈ 1.25 per inch R \approx 1.25\text{ per inch} R ≈ 1.25 per inch for softwood lumber, so a 2 × 4 2\times 4 2 × 4 stud has R ≈ 4.38 R \approx 4.38 R ≈ 4.38 , and a 2 × 6 2\times 6 2 × 6 stud has R ≈ 6.88 R \approx 6.88 R ≈ 6.88 ).

To calculate the true effective assembly U U U -factor ( U effective U_{\text{effective}} U effective ​ ), Manual J utilizes parallel path analysis weighted by the assembly's framing factor ( F F FF FF ): U effective = ( U framing × F F ) + ( U cavity × ( 1 − F F ) ) U_{\text{effective}} = (U_{\text{framing}} \times FF) + (U_{\text{cavity}} \times (1 - FF)) U effective ​ = ( U framing ​ × FF ) + ( U cavity ​ × ( 1 − FF ))

Standard 16 " 16" 16" on-center ( 16 " o.c. 16"\text{ o.c.} 16" o.c. ) wall framing: Framing accounts for approximately 25 % 25\% 25% of the opaque wall area ( F F = 0.25 FF = 0.25 FF = 0.25 ).

Advanced 24 " 24" 24" on-center ( 24 " o.c. 24"\text{ o.c.} 24" o.c. ) framing (Ove framing): Framing accounts for approximately 15 % 15\% 15% to 18 % 18\% 18% of the opaque wall area ( F F = 0.15 − 0.18 FF = 0.15 - 0.18 FF = 0.15 − 0.18 ).

  • Step-by-Step Calculation: Wall Assembly Conductive Heat Loss
  • Problem Statement

Calculate the total design heating heat loss ( q heat q_{\text{heat}} q heat ​ in BTU/h \text{BTU/h} BTU/h ) for an exterior wall assembly in Charlotte, NC ( T out = 22 ∘ F T_{\text{out}} = 22^\circ\text{F} T out ​ = 2 2 ∘ F , T in = 70 ∘ F T_{\text{in}} = 70^\circ\text{F} T in ​ = 7 0 ∘ F , Δ T = 48 ∘ F \Delta T = 48^\circ\text{F} Δ T = 4 8 ∘ F ). The gross wall area is 800 sq ft 800\text{ sq ft} 800 sq ft containing 120 sq ft 120\text{ sq ft} 120 sq ft of windows and 40 sq ft 40\text{ sq ft} 40 sq ft of exterior doors. The wall is constructed of 2 × 4 2\times 4 2 × 4 framing ( 16 " o.c. 16"\text{ o.c.} 16" o.c. , F F = 0.25 FF = 0.25 FF = 0.25 ) with nominal R − 13 R-13 R − 13 fiberglass batt cavity insulation, 1 / 2 " 1/2" 1/2" interior gypsum drywall, 1 / 2 " 1/2" 1/2" exterior OSB sheathing, and vinyl siding.

Step 1: Calculate Net Opaque Wall Area ( A net A_{\text{net}} A net ​ ) A net = A gross − A windows − A doors A_{\text{net}} = A_{\text{gross}} - A_{\text{windows}} - A_{\text{doors}} A net ​ = A gross ​ − A windows ​ − A doors ​ A net = 800 sq ft − 120 sq ft − 40 sq ft = 640 sq ft A_{\text{net}} = 800\text{ sq ft} - 120\text{ sq ft} - 40\text{ sq ft} = 640\text{ sq ft} A net ​ = 800 sq ft − 120 sq ft − 40 sq ft = 640 sq ft

Step 2: Sum Series Resistances for Cavity and Framing Paths

  • Layer Cavity Path R R R -Value Framing Path R R R -Value ( 2 × 4 2\times 4 2 × 4 Stud)
  • Outside Air Film ( R o R_o R o ​ ) 0.17 0.17 0.17 0.17 0.17 0.17
  • Vinyl Siding & Air Space 0.60 0.60 0.60 0.60 0.60 0.60
  • 1 / 2 " 1/2" 1/2" OSB Sheathing 0.62 0.62 0.62 0.62 0.62 0.62

Insulation / Stud ( 3.5 " 3.5" 3.5" ) 13.00 13.00 13.00 ( R − 13 R-13 R − 13 batt) 4.38 4.38 4.38 ( 2 × 4 2\times 4 2 × 4 wood stud)

  • 1 / 2 " 1/2" 1/2" Gypsum Drywall 0.45 0.45 0.45 0.45 0.45 0.45
  • Inside Air Film ( R i R_i R i ​ ) 0.68 0.68 0.68 0.68 0.68 0.68

Total Path Resistance ( R total R_{\text{total}} R total ​ ) 15.52 hr ⋅ ft 2 ⋅ ∘ F / BTU 15.52\text{ hr}\cdot\text{ft}^2\cdot^\circ\text{F}/\text{BTU} 15.52 hr ⋅ ft 2 ⋅ ∘ F / BTU 6.90 hr ⋅ ft 2 ⋅ ∘ F / BTU 6.90\text{ hr}\cdot\text{ft}^2\cdot^\circ\text{F}/\text{BTU} 6.90 hr ⋅ ft 2 ⋅ ∘ F / BTU

Step 3: Compute Path U U U -Factors U cavity = 1 15.52 = 0.0644 BTU / ( hr ⋅ ft 2 ⋅ ∘ F ) U_{\text{cavity}} = \frac{1}{15.52} = 0.0644\text{ BTU}/(\text{hr}\cdot\text{ft}^2\cdot^\circ\text{F}) U cavity ​ = 15.52 1 ​ = 0.0644 BTU / ( hr ⋅ ft 2 ⋅ ∘ F ) U framing = 1 6.90 = 0.1449 BTU / ( hr ⋅ ft 2 ⋅ ∘ F ) U_{\text{framing}} = \frac{1}{6.90} = 0.1449\text{ BTU}/(\text{hr}\cdot\text{ft}^2\cdot^\circ\text{F}) U framing ​ = 6.90 1 ​ = 0.1449 BTU / ( hr ⋅ ft 2 ⋅ ∘ F )

Step 4: Compute Area-Weighted Effective Assembly U U U -Factor ( U effective U_{\text{effective}} U effective ​ ) U effective = ( 0.1449 × 0.25 ) + ( 0.0644 × 0.75 ) U_{\text{effective}} = (0.1449 \times 0.25) + (0.0644 \times 0.75) U effective ​ = ( 0.1449 × 0.25 ) + ( 0.0644 × 0.75 ) U effective = 0.0362 + 0.0483 = 0.0845 BTU / ( hr ⋅ ft 2 ⋅ ∘ F ) U_{\text{effective}} = 0.0362 + 0.0483 = 0.0845\text{ BTU}/(\text{hr}\cdot\text{ft}^2\cdot^\circ\text{F}) U effective ​ = 0.0362 + 0.0483 = 0.0845 BTU / ( hr ⋅ ft 2 ⋅ ∘ F )

(Note: True assembly effective resistance is R effective = 1 / 0.0845 = 11.83 R_{\text{effective}} = 1 / 0.0845 = 11.83 R effective ​ = 1/0.0845 = 11.83 , not nominal R − 13 R-13 R − 13 ).

Step 5: Compute Total Conductive Heat Loss q = U effective × A net × Δ T q = U_{\text{effective}} \times A_{\text{net}} \times \Delta T q = U effective ​ × A net ​ × Δ T q = 0.0845 BTU / ( hr ⋅ ft 2 ⋅ ∘ F ) × 640 sq ft × 48 ∘ F q = 0.0845\text{ BTU}/(\text{hr}\cdot\text{ft}^2\cdot^\circ\text{F}) \times 640\text{ sq ft} \times 48^\circ\text{F} q = 0.0845 BTU / ( hr ⋅ ft 2 ⋅ ∘ F ) × 640 sq ft × 4 8 ∘ F q = 2,595.84 BTU/h ≈ 2,596 BTU/h q = 2{,}595.84\text{ BTU/h} \approx 2{,}596\text{ BTU/h} q = 2 , 595.84 BTU/h ≈ 2 , 596 BTU/h

Loading diagram... ACCA Manual J Load Calculation Workflow & Boundary Conditions