Study guide

7.1 Natural Gas & Propane Combustion Fundamentals

North Carolina HVAC Contractor License Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: North Carolina HVAC Licensing Framework & Board Jurisprudence

1.1 NC Dual-Board Regulatory Structure & General Statutes 1.2 Heating Classifications, Groups & Scopes 1.3 Examination Prerequisites, Qualifier Responsibilities & Disciplinary Rules 1.4 Examination Logistics, Reference Books & Code Editions

2 Chapter 2: North Carolina Business Organizations, Contracts & Lien Law

2.1 Construction Contracts, Project Management & Bidding 2.2 North Carolina Mechanics' Lien Law & Bond Claims 2.3 Business Organizations, Financial Management & Taxation

3 Chapter 3: Construction Safety, Electrical Safety & EPA 608

3.1 OSHA 1926 Construction Safety & Job Site Protocols 3.2 Electrical Safety, NFPA 70E & Lockout/Tagout (LOTO) 3.3 EPA Section 608 & Refrigerant Transition Regulations

4 Chapter 4: Thermodynamics, Refrigeration Cycle & Psychrometrics

4.1 Fundamentals of Thermodynamics & Heat Transfer 4.2 The Mechanical Refrigeration Cycle & Component Dynamics 4.3 Psychrometric Properties, Air Processes & Chart Navigation

5 Chapter 5: ACCA Manual J & Manual N Load Calculations

5.1 Manual J Design Conditions & Thermal Parameters 5.2 Fenestration, Opaque Envelope & Internal Heat Gains 5.3 Infiltration, Duct Losses & Total Block Load Synthesis 5.4 ACCA Manual N Commercial Load Calculation

6 Chapter 6: ACCA Manual D & Manual Q Duct Design & Air Distribution

6.1 Fan Laws, Airflow Dynamics & Total External Static Pressure 6.2 ACCA Manual D Sizing Protocol & Friction Rate Calculation 6.3 SMACNA Duct Construction, Fittings & Air Balancing 6.4 ACCA Manual Q Commercial Low-Pressure Duct Design

7 Chapter 7: Forced Air Heating, Gas Furnaces & Fuel Piping

7.1 Natural Gas & Propane Combustion Fundamentals 7.2 Gas Furnace Operation, Sequence of Control & Diagnostics 7.3 Fuel Oil Heating Systems & Code-Compliant Fuel Gas Piping

8 Chapter 8: Heat Pumps, Inverters & Commercial System Selection (Manual CS)

8.1 Heat Pump Operating Principles, Reversing Valves & Physics 8.2 Defrost Controls, Supplemental Electric Heat & Balance Points 8.3 Inverter Mini-Splits & Variable Refrigerant Flow (VRF) Systems 8.4 Manual CS: Commercial Applications, Systems & Equipment

9 Chapter 9: Hydronic Heating, Steam Systems & Boilers (H1)

9.1 Hydronic Fundamentals, Boiler Classifications & Steam Systems 9.2 Hydronic Piping Layouts, Circulator Pumps & Head Loss Calculations 9.3 Boiler Trim, Expansion Tanks, Air Elimination & Safety Controls 9.4 The NC Uniform Boiler & Pressure Vessel Act (H1 Reference)

10 Chapter 10: Commercial Refrigeration & NC Board Regulations

10.1 NC State Board of Refrigeration Contractors Statutes & Licensure 10.2 Commercial Refrigeration Systems, Multiplex Racks & Defrost Protocols 10.3 Walk-In Coolers, Freezers, Evaporator Pressure Regulators & Valves

11 Chapter 11: NC Administration, Mechanical, Fuel Gas & Energy Codes

11.1 North Carolina Mechanical Code: Equipment Access, Clearances & Condensate 11.2 Ventilation Rates, Exhaust Systems & Duct Smoke Detection 11.3 NC Fuel Gas Code: Combustion Air, Venting & Gas Appliance Installation 11.4 NC Energy Conservation Code: Duct Testing, Envelope & Efficiency Standards 11.5 NC Administrative Code & Policies: Permits, Inspections & Plan Review

12 Chapter 12: Electrical Fundamentals, Motor Controls & Diagnostics

12.1 HVAC Electrical Fundamentals, Circuit Schematics & Power Distribution 12.2 Electric Motors, Capacitors & Motor Controls 12.3 Systematic HVAC Diagnostics, Superheat/Subcooling & Airflow Troubleshooting 12.4 System Commissioning, Testing, Adjusting & Balancing (TAB)

7.1 Natural Gas & Propane Combustion Fundamentals

Key Takeaways Explain This Topic AI

Natural gas (predominantly methane, specific gravity 0.60) is lighter than air and delivers approximately 1,000 to 1,050 BTU/cu ft, whereas LP/propane (specific gravity 1.52) is heavier than air and delivers approximately 2,500 BTU/cu ft.

Complete stoichiometric combustion requires primary air mixed in the burner venturi, secondary air surrounding the flame, and 20% to 50% excess air to prevent incomplete combustion and deadly carbon monoxide (CO) generation.

North Carolina Fuel Gas Code mandates combustion air sizing via the Standard Method (50 cu ft per 1,000 BTU/hr indoor volume) or outdoor air openings sized at 1 sq in. per 4,000 BTU/hr (vertical ducts/direct openings) or 1 sq in. per 2,000 BTU/hr (horizontal ducts).

High-altitude installations require a fuel input derate of 4% per 1,000 feet of elevation above 2,000 feet to compensate for reduced atmospheric air density and prevent fuel-rich burning.

Flue gas diagnostic analysis utilizes carbon dioxide (7.5%–9.0% for natural gas, 9.0%–11.5% for propane), oxygen (5%–9%), and air-free carbon monoxide levels (< 400 ppm per ANSI Z21.47, ideally < 50 ppm in practice) to verify combustion efficiency.

Last updated: August 2026

Natural Gas & Propane Combustion Fundamentals

Quick Reference: Combustion is a rapid, exothermic chemical reaction between hydrocarbon fuel and oxygen. Natural gas (methane, CH 4 \text{CH}_4 CH 4 ​ ) has a specific gravity of 0.60 0.60 0.60 (lighter than air) and a higher heating value of 1 , 000 − 1 , 050 BTU/cu ft 1,000 - 1,050\text{ BTU/cu ft} 1 , 000 − 1 , 050 BTU/cu ft . Propane ( C 3 H 8 \text{C}_3\text{H}_8 C 3 ​ H 8 ​ ) has a specific gravity of 1.52 1.52 1.52 (heavier than air) and a heating value of 2 , 500 BTU/cu ft 2,500\text{ BTU/cu ft} 2 , 500 BTU/cu ft . Complete combustion requires 10 cu ft 10\text{ cu ft} 10 cu ft of air per cubic foot of natural gas and 24 − 25 cu ft 24 - 25\text{ cu ft} 24 − 25 cu ft of air per cubic foot of propane, plus 20 % − 50 % 20\% - 50\% 20% − 50% excess air to prevent toxic carbon monoxide ( CO \text{CO} CO ) production.

1. Fuel Gas Physical Properties & Combustion Chemistry

Understanding the physical and thermodynamic differences between Natural Gas (Methane) and Liquefied Petroleum Gas (LP / Propane) is foundational for equipment selection, burner orifice sizing, manifold pressure setting, and field safety.

Property / Parameter Natural Gas (Methane, CH 4 \text{CH}_4 CH 4 ​ ) Liquefied Petroleum Gas (Propane, C 3 H 8 \text{C}_3\text{H}_8 C 3 ​ H 8 ​ )

Primary Chemical Composition Methane ( > 90 % CH 4 > 90\%\text{ CH}_4 > 90% CH 4 ​ , balance ethane/nitrogen) Propane ( > 95 % C 3 H 8 > 95\%\text{ C}_3\text{H}_8 > 95% C 3 ​ H 8 ​ )

Specific Gravity of Gas (Air = 1.00) 0.60 0.60 0.60 (Lighter than air; rises and disperses) 1.52 1.52 1.52 (Heavier than air; sinks, pools in low areas/crawlspaces)

Higher Heating Value (HHV / Gross) ≈ 1 , 000 − 1 , 050 BTU/cu ft \approx 1,000 - 1,050\text{ BTU/cu ft} ≈ 1 , 000 − 1 , 050 BTU/cu ft (Std: 1 , 000 BTU/ft 3 1,000\text{ BTU/ft}^3 1 , 000 BTU/ft 3 ) ≈ 2 , 500 BTU/cu ft \approx 2,500\text{ BTU/cu ft} ≈ 2 , 500 BTU/cu ft ( 91 , 500 BTU/gallon 91,500\text{ BTU/gallon} 91 , 500 BTU/gallon liquid)

Specific Gravity of Liquid (Water = 1.00) 0.42 0.42 0.42 (Cryogenic liquid) 0.504 − 0.510 0.504 - 0.510 0.504 − 0.510 at 60 ∘ F 60^\circ\text{F} 6 0 ∘ F

Flammability Limits in Air (% Volume) 4.0 % − 15.0 % 4.0\% - 15.0\% 4.0% − 15.0% (Lower Limit: 4 − 5 % 4-5\% 4 − 5% , Upper Limit: 15 % 15\% 15% ) 2.15 % − 9.60 % 2.15\% - 9.60\% 2.15% − 9.60% (Narrower flammability band)

Ignition Temperature 1 , 100 ∘ F − 1 , 200 ∘ F 1,100^\circ\text{F} - 1,200^\circ\text{F} 1 , 10 0 ∘ F − 1 , 20 0 ∘ F ( 593 ∘ C − 649 ∘ C 593^\circ\text{C} - 649^\circ\text{C} 59 3 ∘ C − 64 9 ∘ C ) 920 ∘ F − 1 , 020 ∘ F 920^\circ\text{F} - 1,020^\circ\text{F} 92 0 ∘ F − 1 , 02 0 ∘ F ( 493 ∘ C − 549 ∘ C 493^\circ\text{C} - 549^\circ\text{C} 49 3 ∘ C − 54 9 ∘ C )

Theoretical Air Required for Combustion ≈ 10.0 cu ft air / 1.0 cu ft gas \approx 10.0\text{ cu ft air} / 1.0\text{ cu ft gas} ≈ 10.0 cu ft air /1.0 cu ft gas ≈ 24.0 − 25.0 cu ft air / 1.0 cu ft gas \approx 24.0 - 25.0\text{ cu ft air} / 1.0\text{ cu ft gas} ≈ 24.0 − 25.0 cu ft air /1.0 cu ft gas

Standard Manifold Operating Pressure 3.5 in. w.c. 3.5\text{ in. w.c.} 3.5 in. w.c. ( 0.126 psig 0.126\text{ psig} 0.126 psig ) 10.0 − 11.0 in. w.c. 10.0 - 11.0\text{ in. w.c.} 10.0 − 11.0 in. w.c. (Std: 10.0 or 11.0 in. w.c. 10.0\text{ or } 11.0\text{ in. w.c.} 10.0 or 11.0 in. w.c. )

Nominal Supply Line Inlet Pressure 5.0 − 7.0 in. w.c. 5.0 - 7.0\text{ in. w.c.} 5.0 − 7.0 in. w.c. (Max 10.5 − 14.0 in. w.c. 10.5 - 14.0\text{ in. w.c.} 10.5 − 14.0 in. w.c. ) 11.0 − 13.0 in. w.c. 11.0 - 13.0\text{ in. w.c.} 11.0 − 13.0 in. w.c. (Max 14.0 in. w.c. 14.0\text{ in. w.c.} 14.0 in. w.c. / 0.5 psig 0.5\text{ psig} 0.5 psig )

Odorant Added for Leak Detection Ethyl Mercaptan / THT ( t t t -butyl mercaptan) Ethyl Mercaptan ( 1.0 lb / 10 , 000 gal 1.0\text{ lb} / 10,000\text{ gal} 1.0 lb /10 , 000 gal )

Stoichiometric Chemical Reactions

Stoichiometric (perfect) combustion represents the exact theoretical proportion of fuel and pure oxygen where all carbon converts to carbon dioxide ( CO 2 \text{CO}_2 CO 2 ​ ) and all hydrogen converts to water vapor ( H 2 O \text{H}_2\text{O} H 2 ​ O ), releasing maximum heat without unburned fuel or excess oxygen.

Natural Gas (Methane) Perfect Combustion Reaction: CH 4 + 2 O 2 ⟶ CO 2 + 2 H 2 O + Heat (approx. 1 , 050 BTU) \text{CH}_4 + 2\text{O}_2 \longrightarrow \text{CO}_2 + 2\text{H}_2\text{O} + \text{Heat (approx. } 1,050\text{ BTU)} CH 4 ​ + 2 O 2 ​ ⟶ CO 2 ​ + 2 H 2 ​ O + Heat (approx. 1 , 050 BTU)

Because atmospheric air consists of approximately 20.9 % 20.9\% 20.9% oxygen and 79.1 % 79.1\% 79.1% nitrogen by volume, every 1 cu ft 1\text{ cu ft} 1 cu ft of O 2 \text{O}_2 O 2 ​ brings 3.78 cu ft 3.78\text{ cu ft} 3.78 cu ft of inert nitrogen ( N 2 \text{N}_2 N 2 ​ ). Therefore, 2 cu ft 2\text{ cu ft} 2 cu ft of pure O 2 \text{O}_2 O 2 ​ requires 2 / 0.209 = 9.57 cu ft 2 / 0.209 = 9.57\text{ cu ft} 2/0.209 = 9.57 cu ft of atmospheric air (nominally 10 cu ft 10\text{ cu ft} 10 cu ft ). CH 4 + 2 O 2 + 7.56 N 2 ⟶ CO 2 + 2 H 2 O + 7.56 N 2 + Heat \text{CH}_4 + 2\text{O}_2 + 7.56\text{N}_2 \longrightarrow \text{CO}_2 + 2\text{H}_2\text{O} + 7.56\text{N}_2 + \text{Heat} CH 4 ​ + 2 O 2 ​ + 7.56 N 2 ​ ⟶ CO 2 ​ + 2 H 2 ​ O + 7.56 N 2 ​ + Heat

Propane Perfect Combustion Reaction: C 3 H 8 + 5 O 2 ⟶ 3 CO 2 + 4 H 2 O + Heat (approx. 2 , 500 BTU) \text{C}_3\text{H}_8 + 5\text{O}_2 \longrightarrow 3\text{CO}_2 + 4\text{H}_2\text{O} + \text{Heat (approx. } 2,500\text{ BTU)} C 3 ​ H 8 ​ + 5 O 2 ​ ⟶ 3 CO 2 ​ + 4 H 2 ​ O + Heat (approx. 2 , 500 BTU)

*Accounting for atmospheric nitrogen ( 5 cu ft O 2 × 4.78 = 23.9 cu ft air 5\text{ cu ft } \text{O}_2 \times 4.78 = 23.9\text{ cu ft air} 5 cu ft O 2 ​ × 4.78 = 23.9 cu ft air ): C 3 H 8 + 5 O 2 + 18.9 N 2 ⟶ 3 CO 2 + 4 H 2 O + 18.9 N 2 + Heat \text{C}_3\text{H}_8 + 5\text{O}_2 + 18.9\text{N}_2 \longrightarrow 3\text{CO}_2 + 4\text{H}_2\text{O} + 18.9\text{N}_2 + \text{Heat} C 3 ​ H 8 ​ + 5 O 2 ​ + 18.9 N 2 ​ ⟶ 3 CO 2 ​ + 4 H 2 ​ O + 18.9 N 2 ​ + Heat

2. Classification of Combustion Air

In actual gas heating appliances, gas and air do not mix with molecular perfection. To guarantee complete combustion and avoid lethal carbon monoxide formation, appliances require multiple air stages and excess air: +-----------------------------------------------------------------------------------------+

  • | TOTAL AIR SUPPLIED TO APPLIANCE |
  • | |
  • | +--------------------------------------+ +--------------------------------------------+ |
  • | | COMBUSTION AIR (15 cu ft) | | DILUTION AIR (Category I) | |
  • | | | | | |
  • | | +----------------+ +---------------+ | | (Drawn into draft hood/diverter to cool | |
  • | | | PRIMARY AIR | | SECONDARY AIR | | | flue gases, stabilize chimney draft, | |
  • | | | (30% - 50% | | (50% - 70% | | | and isolate burner from downdrafts) | |
  • | | | mixed in | | drawn around | | | | |
  • | | | burner venturi)| | flame base) | | | | |
  • | | +----------------+ +---------------+ | | | |
  • | | +----------------------------------+ | | | |
  • | | | EXCESS AIR (20% - 50% safety) | | | | |
  • | | +----------------------------------+ | | | |
  • | +--------------------------------------+ +--------------------------------------------+ |
  • +-----------------------------------------------------------------------------------------+

Primary Air: Introduced into the burner body upstream of the ignition point via the gas orifice and venturi mixer tube. The velocity of the high-pressure gas jet exiting the spud orifice draws primary air into the burner via the Bernoulli/venturi effect, providing 30 % 30\% 30% to 50 % 50\% 50% of the air required for complete combustion.

Secondary Air: Atmospheric air supplied directly to the combustion chamber surrounding the burner flames. It diffuses into the outer flame envelope to complete the combustion reaction initiated by the primary air-fuel mixture.

Excess Air: Air supplied to the combustion chamber beyond the stoichiometric theoretical requirement ( 20 % 20\% 20% to 50 % 50\% 50% excess air, typically raising total combustion air to 12 − 15 cu ft 12 - 15\text{ cu ft} 12 − 15 cu ft per cubic foot of natural gas). Excess air ensures complete fuel consumption despite minor variations in gas pressure, air humidity, and burner fouling.

Dilution Air: Ambient air drawn into the draft hood or draft diverter of Category I atmospheric gas appliances. Dilution air mixes with hot combustion gases downstream of the heat exchanger to cool the stack temperature, reduce flue dew point, and maintain consistent chimney draft.

3. Flame Chemistry, Appearance & Abnormalities

Visual inspection of the burner flame is a vital diagnostic procedure for identifying combustion imbalances, improper air shutter adjustment, over-firing, or cracked heat exchangers. CORRECT FLAME YELLOW TIPPING / INCOMPLETE LIFTING FLAME

  • (Blue, Sharp Cones) (Lack of Primary Air) (Excess Velocity / Pressure)
  • /\ /\ /\
  • / \ <-- Outer Envelope (Dark Blue) / \ <-- Soft Yellow Tip (Soot/CO) / \ <-- Flame lifts
  • / /\ \ / /\ \ / /\ \ off burner port
  • / / \ \ / / \ \ / / \ \ (Flame roar)
  • / /____\ \ <-- Inner Cone (Light Blue) / /____\ \ / /____\ \
  • +----------+ +----------+ ~~~~~~~~~~~~ <-- Air gap
  • | BURNER | | BURNER | +----------+
  • | BURNER |
  • Flame Characteristics & Diagnostic Matrix

Flame Condition Visual Characteristic Root Cause Hazard / Impact Corrective Action

Normal Combustion Distinct, light-blue inner cone with stable, darker blue/purple outer mantle; quiet operation Correct air-fuel ratio ( 30 − 50 % 30-50\% 30 − 50% primary air), correct manifold pressure Clean, efficient operation; negligible CO \text{CO} CO ( < 50 ppm < 50\text{ ppm} < 50 ppm ) None; verify with combustion analyzer

Yellow Tipping Luminous, glowing yellow or orange tips on the flame mantle Insufficient primary air; clogged primary air shutter; lint/dust in burner venturi Soot accumulation on heat exchanger; high CO \text{CO} CO production; aldehydes Clean burner venturi tubes; open primary air shutter until yellow disappears

Lifting Flame Flame lifts entirely off burner ports; distinct hissing/roaring sound Excessive gas manifold pressure; excessive primary air velocity; incorrect orifice size Flame sensor lockout; unburned gas escape; delayed ignition explosion Reduce manifold pressure to nameplate rating; close air shutter; check orifice

Flashback Flame burns inside the burner tube/venturi behind the orifice; popping sound Gas velocity exiting ports is lower than burning speed; oversized orifice; low pressure; excess primary air Burner tube overheating; metal warping; fire hazard Increase manifold pressure to spec; replace damaged burner; close primary shutter

Waving / Floating Flame Soft, lazy flame drifting away from burner; lacks defined inner cone Inadequate combustion air; blocked flue passage; negative building pressure Deadly CO \text{CO} CO generation; flue gas spillage at draft hood Provide required combustion air; inspect and clean flue and heat exchanger

Flame Rollout Flames spill outward through burner access opening upon ignition Cracked heat exchanger; completely blocked flue passages; severe downdraft Fire hazard; rollout thermal switch trips ( R − W R-W R − W circuit open) Inspect heat exchanger integrity; clear blocked flue/chimney

4. Incomplete Combustion & Carbon Monoxide (CO) Formation

When hydrocarbon fuels burn in an oxygen-deficient environment, or when the flame is cooled below its ignition temperature before combustion completes (flame impingement on a cold heat exchanger wall), carbon atoms cannot fully oxidize to CO 2 \text{CO}_2 CO 2 ​ .

Incomplete Combustion Reactions: 2 CH 4 + 3 O 2 ⟶ 2 CO + 4 H 2 O + Heat (approx. 600 BTU) 2\text{CH}_4 + 3\text{O}_2 \longrightarrow 2\text{CO} + 4\text{H}_2\text{O} + \text{Heat (approx. } 600\text{ BTU)} 2 CH 4 ​ + 3 O 2 ​ ⟶ 2 CO + 4 H 2 ​ O + Heat (approx. 600 BTU) CH 4 + O 2 ⟶ C (Soot) + 2 H 2 O + Heat (approx. 250 BTU) \text{CH}_4 + \text{O}_2 \longrightarrow \text{C (Soot)} + 2\text{H}_2\text{O} + \text{Heat (approx. } 250\text{ BTU)} CH 4 ​ + O 2 ​ ⟶ C (Soot) + 2 H 2 ​ O + Heat (approx. 250 BTU)

Hazards of Carbon Monoxide (CO)

Carbon monoxide is a colorless, odorless, tasteless, and non-irritating toxic gas. CO \text{CO} CO binds to human hemoglobin with an affinity approximately 200 to 250 times 200\text{ to } 250\text{ times} 200 to 250 times greater than oxygen, forming carboxyhemoglobin ( COHb \text{COHb} COHb ) and starving vital organs of oxygen.

  • | CO Concentration in Air (PPM) | Health Effects & Exposure Time Limits |
  • |---|---||

| 9 ppm 9\text{ ppm} 9 ppm | Maximum allowable indoor air concentration for 8 hours (ASHRAE / EPA ambient standard) |

| 35 ppm 35\text{ ppm} 35 ppm | Maximum allowable continuous 8-hour workplace exposure limit (OSHA PEL) |

| 50 ppm 50\text{ ppm} 50 ppm | Standard field action threshold; investigate source, inspect furnace and heat exchanger |

| 100 − 200 ppm 100 - 200\text{ ppm} 100 − 200 ppm | Slight headache, fatigue, nausea, and dizziness within 2 to 3 hours of exposure |

| 400 ppm 400\text{ ppm} 400 ppm | Frontal headache, life-threatening after 3 hours; ANSI maximum air-free limit in flue gas |

| 800 ppm 800\text{ ppm} 800 ppm | Severe dizziness, nausea, convulsions within 45 minutes; unconsciousness within 2 hours |

| 1 , 600 ppm 1,600\text{ ppm} 1 , 600 ppm | Headache, rapid pulse, dizziness within 20 minutes; death within 1 hour |

| 3 , 200 ppm 3,200\text{ ppm} 3 , 200 ppm | Severe dizziness within 5 to 10 minutes; death within 30 minutes |

| 6 , 400 ppm 6,400\text{ ppm} 6 , 400 ppm | Immediate unconsciousness; death within 10 to 15 minutes |

| 12 , 800 ppm 12,800\text{ ppm} 12 , 800 ppm ( 1.28 % 1.28\% 1.28% ) | Immediate physiological collapse, respiratory arrest, and fatality within 1 to 3 minutes |

5. Code-Mandated Combustion Air Requirements (NC Fuel Gas Code / IFGC Chapter 3 & NFPA 54)

All fuel-burning appliances require an adequate, continuous supply of combustion, ventilation, and dilution air. The North Carolina Fuel Gas Code (NCFGC) and NFPA 54 (National Fuel Gas Code) establish strict geometric calculation rules based on appliance location and building envelope construction.

Method 1: All Combustion Air From Inside the Building (Standard Method)

Applicable when the building is not of unusually tight construction (air infiltration rate ≥ 0.40 ACH \ge 0.40\text{ ACH} ≥ 0.40 ACH ): Required Room Volume = 50 ft 3 per 1 , 000 BTU/hr Total Combined Appliance Input Rating \text{Required Room Volume} = 50\text{ ft}^3 \text{ per } 1,000\text{ BTU/hr Total Combined Appliance Input Rating} Required Room Volume = 50 ft 3 per 1 , 000 BTU/hr Total Combined Appliance Input Rating Required Volume (cu ft) = ( Total Input Rating (BTU/hr) 1 , 000 ) × 50 \text{Required Volume (cu ft)} = \left( \frac{\text{Total Input Rating (BTU/hr)}}{1,000} \right) \times 50 Required Volume (cu ft) = ( 1 , 000 Total Input Rating (BTU/hr) ​ ) × 50

If the space is an Unconfined Space (actual room volume ≥ \ge ≥ required volume), no additional outdoor combustion air openings are required.

If the space is a Confined Space (actual volume < < < required volume), combustion air must be brought in from interconnected rooms via two permanent openings :

One opening within 12 inches 12\text{ inches} 12 inches of the top of the enclosure.

One opening within 12 inches 12\text{ inches} 12 inches of the bottom of the enclosure.

Each opening must provide a minimum free area of 1 sq in. 1\text{ sq in.} 1 sq in. per 1 , 000 BTU/hr 1,000\text{ BTU/hr} 1 , 000 BTU/hr of total appliance input rating, but never less than 100 sq in. 100\text{ sq in.} 100 sq in. total free area.

Method 2: All Combustion Air From Outdoors

When a confined space cannot communicate with interior rooms or when the building has an air infiltration rate < 0.40 ACH < 0.40\text{ ACH} < 0.40 ACH , combustion air must be ducted or opened directly to the outdoors: OUTDOOR COMBUSTION AIR SIZING RULES (NC FUEL GAS CODE)

  • +---------------------------------------------------+---------------------------------------------+
  • | CONFIGURATION | REQUIRED FREE AREA PER 1,000 BTU/HR INPUT |
  • +---------------------------------------------------+---------------------------------------------+
  • | Two Openings: Direct Outdoors or Vertical Ducts | 1 sq in. per 4,000 BTU/hr (Each Opening) |
  • | Two Openings: Horizontal Ducts to Outdoors | 1 sq in. per 2,000 BTU/hr (Each Opening) |
  • | One Opening: Direct Outdoors or Vertical Duct | 1 sq in. per 3,000 BTU/hr (Single Opening) |
  • +---------------------------------------------------+---------------------------------------------+

Two Permanent Openings — Direct Outdoors or Vertical Ducts:

Sizing: 1 sq in. 1\text{ sq in.} 1 sq in. per 4 , 000 BTU/hr 4,000\text{ BTU/hr} 4 , 000 BTU/hr of total appliance input rating.

Location: One opening within 12 inches 12\text{ inches} 12 inches of the ceiling, one within 12 inches 12\text{ inches} 12 inches of the floor.

Vertical ducts must terminate in an attic, crawlspace, or directly outdoors.

Two Permanent Openings — Horizontal Ducts:

Sizing: 1 sq in. 1\text{ sq in.} 1 sq in. per 2 , 000 BTU/hr 2,000\text{ BTU/hr} 2 , 000 BTU/hr of total appliance input rating.

Location: One high (within 12 in. 12\text{ in.} 12 in. of top), one low (within 12 in. 12\text{ in.} 12 in. of bottom).

Note: Horizontal ducts require double the area of vertical ducts ( 1 per 2 , 000 1\text{ per } 2,000 1 per 2 , 000 vs 1 per 4 , 000 1\text{ per } 4,000 1 per 4 , 000 ) due to increased aerodynamic friction and lack of thermal stack buoyancy.

One Permanent Opening — Direct or Vertical/Horizontal Duct:

Sizing: 1 sq in. 1\text{ sq in.} 1 sq in. per 3 , 000 BTU/hr 3,000\text{ BTU/hr} 3 , 000 BTU/hr of total appliance input rating.

Location: Within 12 inches 12\text{ inches} 12 inches of the top of the enclosure.

Appliance clearances: Minimum 1 inch 1\text{ inch} 1 inch sides/back and 6 inches 6\text{ inches} 6 inches front clearance from the appliance to the enclosure walls.

Louver and Screen Free Area Reductions

When calculating the physical dimensions of combustion air grilles, contractors must adjust for the blockage caused by louver blades and mesh screens:

Metal Louvers: 60 % − 75 % 60\% - 75\% 60% − 75% free area (standard rule: use 75 % 75\% 75% if manufacturer data is unavailable).

Wood Louvers: 20 % − 25 % 20\% - 25\% 20% − 25% free area (standard rule: use 25 % 25\% 25% if manufacturer data is unavailable).

Protective Wire Mesh: Mesh size must not be smaller than 1 / 4 inch 1/4\text{ inch} 1/4 inch ( 6.4 mm 6.4\text{ mm} 6.4 mm ) to prevent lint and insect clogs.

Sizing Calculation Example:

A mechanical closet in Raleigh, NC contains a 100 , 000 BTU/hr 100,000\text{ BTU/hr} 100 , 000 BTU/hr gas furnace and a 40 , 000 BTU/hr 40,000\text{ BTU/hr} 40 , 000 BTU/hr gas water heater (Total input = 140 , 000 BTU/hr 140,000\text{ BTU/hr} 140 , 000 BTU/hr ). Two vertical ducts extend into a ventilated attic.

Net Free Area Required per Opening: Net Free Area = 140 , 000 BTU/hr 4 , 000 BTU/hr/sq in. = 35.0 sq inches per opening \text{Net Free Area} = \frac{140,000\text{ BTU/hr}}{4,000\text{ BTU/hr/sq in.}} = 35.0\text{ sq inches per opening} Net Free Area = 4 , 000 BTU/hr/sq in. 140 , 000 BTU/hr ​ = 35.0 sq inches per opening

Physical Grille Sizing with Metal Louvers ( 75 % 75\% 75% free area): Gross Grille Area = 35.0 sq in. 0.75 = 46.67 sq inches ⟹ 6 " × 8 " Grille ( 48 sq in. ) \text{Gross Grille Area} = \frac{35.0\text{ sq in.}}{0.75} = 46.67\text{ sq inches} \quad \implies \quad 6" \times 8"\text{ Grille } (48\text{ sq in.}) Gross Grille Area = 0.75 35.0 sq in. ​ = 46.67 sq inches ⟹ 6" × 8" Grille ( 48 sq in. )

Physical Grille Sizing with Wood Louvers ( 25 % 25\% 25% free area): Gross Grille Area = 35.0 sq in. 0.25 = 140.0 sq inches ⟹ 10 " × 14 " Grille ( 140 sq in. ) \text{Gross Grille Area} = \frac{35.0\text{ sq in.}}{0.25} = 140.0\text{ sq inches} \quad \implies \quad 10" \times 14"\text{ Grille } (140\text{ sq in.}) Gross Grille Area = 0.25 35.0 sq in. ​ = 140.0 sq inches ⟹ 10" × 14" Grille ( 140 sq in. )

6. High-Altitude Appliance Derating

As altitude increases, atmospheric barometric pressure and air density decrease ( 29.92 in. Hg 29.92\text{ in. Hg} 29.92 in. Hg at sea level vs 24.6 in. Hg 24.6\text{ in. Hg} 24.6 in. Hg at 5 , 000 ft 5,000\text{ ft} 5 , 000 ft ). Because atmospheric gas burners draw air by volume rather than mass, an unadjusted burner will ingest less oxygen by weight, causing rich burning, severe soot formation, and carbon monoxide generation.

NFPA 54 & NCFGC High-Altitude Derate Rule:

Up to 2 , 000 ft 2,000\text{ ft} 2 , 000 ft Elevation: No derating required ( 100 % 100\% 100% nameplate firing rate).

Above 2 , 000 ft 2,000\text{ ft} 2 , 000 ft Elevation: Derate appliance input rating by 4 % 4\% 4% for every 1 , 000 ft 1,000\text{ ft} 1 , 000 ft of elevation above sea level. Derate Percentage (%) = 0.04 × ( Elevation (ft) 1 , 000 ) \text{Derate Percentage (\%)} = 0.04 \times \left( \frac{\text{Elevation (ft)}}{1,000} \right) Derate Percentage (%) = 0.04 × ( 1 , 000 Elevation (ft) ​ ) Adjusted High-Altitude Input (BTU/hr) = Nameplate Input (BTU/hr) × [ 1 − 0.04 × ( Elevation (ft) 1 , 000 ) ] \text{Adjusted High-Altitude Input (BTU/hr)} = \text{Nameplate Input (BTU/hr)} \times \left[ 1 - 0.04 \times \left( \frac{\text{Elevation (ft)}}{1,000} \right) \right] Adjusted High-Altitude Input (BTU/hr) = Nameplate Input (BTU/hr) × [ 1 − 0.04 × ( 1 , 000 Elevation (ft) ​ ) ]

Worked Example: Derating in the Blue Ridge Mountains (Boone, NC)

A gas furnace with a sea-level nameplate input rating of 80 , 000 BTU/hr 80,000\text{ BTU/hr} 80 , 000 BTU/hr is installed in Boone, NC at an elevation of 3 , 500 ft 3,500\text{ ft} 3 , 500 ft :

Calculate Derate Factor: Derate = 4 % × ( 3 , 500 1 , 000 ) = 4 % × 3.5 = 14.0 % \text{Derate} = 4\% \times \left( \frac{3,500}{1,000} \right) = 4\% \times 3.5 = 14.0\% Derate = 4% × ( 1 , 000 3 , 500 ​ ) = 4% × 3.5 = 14.0%

Calculate Required Firing Input Rate: Adjusted Input = 80 , 000 × ( 1 − 0.14 ) = 80 , 000 × 0.86 = 68 , 800 BTU/hr \text{Adjusted Input} = 80,000 \times (1 - 0.14) = 80,000 \times 0.86 = 68,800\text{ BTU/hr} Adjusted Input = 80 , 000 × ( 1 − 0.14 ) = 80 , 000 × 0.86 = 68 , 800 BTU/hr

Field Adjustment: The installing contractor must install smaller main burner spud orifices (or adjust manifold pressure in accordance with manufacturer high-altitude conversion kits) to achieve 68 , 800 BTU/hr 68,800\text{ BTU/hr} 68 , 800 BTU/hr .

7. Flue Gas Combustion Analysis & Diagnostics

Modern electronic combustion analyzers measure flue gas constituents ( O 2 \text{O}_2 O 2 ​ , CO \text{CO} CO , stack temperature) and calculate combustion efficiency, excess air percentage, and carbon dioxide ( CO 2 \text{CO}_2 CO 2 ​ ).

Combustion Parameter Benchmarks

Parameter Natural Gas (Atmospheric 80%) Natural Gas (Condensing 90%+) LP / Propane (All Types)

Oxygen ( O 2 \text{O}_2 O 2 ​ ) 6.0 % − 9.0 % 6.0\% - 9.0\% 6.0% − 9.0% 4.5 % − 7.5 % 4.5\% - 7.5\% 4.5% − 7.5% 4.5 % − 7.5 % 4.5\% - 7.5\% 4.5% − 7.5%

Carbon Dioxide ( CO 2 \text{CO}_2 CO 2 ​ ) 7.0 % − 9.0 % 7.0\% - 9.0\% 7.0% − 9.0% (Max theoretical 11.9 % 11.9\% 11.9% ) 8.0 % − 9.8 % 8.0\% - 9.8\% 8.0% − 9.8% 9.0 % − 11.5 % 9.0\% - 11.5\% 9.0% − 11.5% (Max theoretical 13.8 % 13.8\% 13.8% )

Excess Air 30 % − 50 % 30\% - 50\% 30% − 50% 20 % − 40 % 20\% - 40\% 20% − 40% 20 % − 40 % 20\% - 40\% 20% − 40%

Gross Flue Gas Temp 325 ∘ F − 450 ∘ F 325^\circ\text{F} - 450^\circ\text{F} 32 5 ∘ F − 45 0 ∘ F 90 ∘ F − 130 ∘ F 90^\circ\text{F} - 130^\circ\text{F} 9 0 ∘ F − 13 0 ∘ F Matches appliance AFUE class

Net Stack Temp ( T flue − T room T_{\text{flue}} - T_{\text{room}} T flue ​ − T room ​ ) 250 ∘ F − 380 ∘ F 250^\circ\text{F} - 380^\circ\text{F} 25 0 ∘ F − 38 0 ∘ F 25 ∘ F − 60 ∘ F 25^\circ\text{F} - 60^\circ\text{F} 2 5 ∘ F − 6 0 ∘ F Matches appliance AFUE class

Flue CO (As-Measured) < 50 ppm < 50\text{ ppm} < 50 ppm < 50 ppm < 50\text{ ppm} < 50 ppm < 50 ppm < 50\text{ ppm} < 50 ppm

Air-Free CO ( CO AF \text{CO}_{\text{AF}} CO AF ​ ) < 400 ppm < 400\text{ ppm} < 400 ppm (ANSI Z21.47 max) < 400 ppm < 400\text{ ppm} < 400 ppm (ANSI Z21.47 max) < 400 ppm < 400\text{ ppm} < 400 ppm (ANSI Z21.47 max)

Air-Free Carbon Monoxide Formula (ANSI Z21.47 / EPA)

Because dilution air and excess air artificially dilute the measured CO \text{CO} CO concentration in flue gas, combustion diagnostics use Air-Free CO \text{CO} CO ( CO AF \text{CO}_{\text{AF}} CO AF ​ ) to calculate the true concentration generated in an undiluted combustion stream: CO air-free = CO measured × ( 20.9 20.9 − % O 2 , measured ) \text{CO}_{\text{air-free}} = \text{CO}_{\text{measured}} \times \left( \frac{20.9}{20.9 - \%\text{O}_{2,\text{measured}}} \right) CO air-free ​ = CO measured ​ × ( 20.9 − % O 2 , measured ​ 20.9 ​ ) CO air-free = CO measured × ( % CO 2 , ultimate % CO 2 , measured ) \text{CO}_{\text{air-free}} = \text{CO}_{\text{measured}} \times \left( \frac{\%\text{CO}_{2,\text{ultimate}}}{\%\text{CO}_{2,\text{measured}}} \right) CO air-free ​ = CO measured ​ × ( % CO 2 , measured ​ % CO 2 , ultimate ​ ​ )

Example: An atmospheric furnace flue measures 35 ppm CO 35\text{ ppm CO} 35 ppm CO with an oxygen reading of 8.0 % O 2 8.0\% \text{ O}_2 8.0% O 2 ​ : CO air-free = 35 × ( 20.9 20.9 − 8.0 ) = 35 × ( 20.9 12.9 ) = 35 × 1.62 = 56.7 ppm air-free \text{CO}_{\text{air-free}} = 35 \times \left( \frac{20.9}{20.9 - 8.0} \right) = 35 \times \left( \frac{20.9}{12.9} \right) = 35 \times 1.62 = 56.7\text{ ppm air-free} CO air-free ​ = 35 × ( 20.9 − 8.0 20.9 ​ ) = 35 × ( 12.9 20.9 ​ ) = 35 × 1.62 = 56.7 ppm air-free

Loading diagram... Combustion Air Sizing & Opening Decision Tree (NC Fuel Gas Code)

Combustion Air Volumetric Proportion for 1 cu ft Natural Gas (with 50% Excess Air)