Study guide

7.3 Fuel Oil Heating Systems & Code-Compliant Fuel Gas Piping

North Carolina HVAC Contractor License Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: North Carolina HVAC Licensing Framework & Board Jurisprudence

1.1 NC Dual-Board Regulatory Structure & General Statutes 1.2 Heating Classifications, Groups & Scopes 1.3 Examination Prerequisites, Qualifier Responsibilities & Disciplinary Rules 1.4 Examination Logistics, Reference Books & Code Editions

2 Chapter 2: North Carolina Business Organizations, Contracts & Lien Law

2.1 Construction Contracts, Project Management & Bidding 2.2 North Carolina Mechanics' Lien Law & Bond Claims 2.3 Business Organizations, Financial Management & Taxation

3 Chapter 3: Construction Safety, Electrical Safety & EPA 608

3.1 OSHA 1926 Construction Safety & Job Site Protocols 3.2 Electrical Safety, NFPA 70E & Lockout/Tagout (LOTO) 3.3 EPA Section 608 & Refrigerant Transition Regulations

4 Chapter 4: Thermodynamics, Refrigeration Cycle & Psychrometrics

4.1 Fundamentals of Thermodynamics & Heat Transfer 4.2 The Mechanical Refrigeration Cycle & Component Dynamics 4.3 Psychrometric Properties, Air Processes & Chart Navigation

5 Chapter 5: ACCA Manual J & Manual N Load Calculations

5.1 Manual J Design Conditions & Thermal Parameters 5.2 Fenestration, Opaque Envelope & Internal Heat Gains 5.3 Infiltration, Duct Losses & Total Block Load Synthesis 5.4 ACCA Manual N Commercial Load Calculation

6 Chapter 6: ACCA Manual D & Manual Q Duct Design & Air Distribution

6.1 Fan Laws, Airflow Dynamics & Total External Static Pressure 6.2 ACCA Manual D Sizing Protocol & Friction Rate Calculation 6.3 SMACNA Duct Construction, Fittings & Air Balancing 6.4 ACCA Manual Q Commercial Low-Pressure Duct Design

7 Chapter 7: Forced Air Heating, Gas Furnaces & Fuel Piping

7.1 Natural Gas & Propane Combustion Fundamentals 7.2 Gas Furnace Operation, Sequence of Control & Diagnostics 7.3 Fuel Oil Heating Systems & Code-Compliant Fuel Gas Piping

8 Chapter 8: Heat Pumps, Inverters & Commercial System Selection (Manual CS)

8.1 Heat Pump Operating Principles, Reversing Valves & Physics 8.2 Defrost Controls, Supplemental Electric Heat & Balance Points 8.3 Inverter Mini-Splits & Variable Refrigerant Flow (VRF) Systems 8.4 Manual CS: Commercial Applications, Systems & Equipment

9 Chapter 9: Hydronic Heating, Steam Systems & Boilers (H1)

9.1 Hydronic Fundamentals, Boiler Classifications & Steam Systems 9.2 Hydronic Piping Layouts, Circulator Pumps & Head Loss Calculations 9.3 Boiler Trim, Expansion Tanks, Air Elimination & Safety Controls 9.4 The NC Uniform Boiler & Pressure Vessel Act (H1 Reference)

10 Chapter 10: Commercial Refrigeration & NC Board Regulations

10.1 NC State Board of Refrigeration Contractors Statutes & Licensure 10.2 Commercial Refrigeration Systems, Multiplex Racks & Defrost Protocols 10.3 Walk-In Coolers, Freezers, Evaporator Pressure Regulators & Valves

11 Chapter 11: NC Administration, Mechanical, Fuel Gas & Energy Codes

11.1 North Carolina Mechanical Code: Equipment Access, Clearances & Condensate 11.2 Ventilation Rates, Exhaust Systems & Duct Smoke Detection 11.3 NC Fuel Gas Code: Combustion Air, Venting & Gas Appliance Installation 11.4 NC Energy Conservation Code: Duct Testing, Envelope & Efficiency Standards 11.5 NC Administrative Code & Policies: Permits, Inspections & Plan Review

12 Chapter 12: Electrical Fundamentals, Motor Controls & Diagnostics

12.1 HVAC Electrical Fundamentals, Circuit Schematics & Power Distribution 12.2 Electric Motors, Capacitors & Motor Controls 12.3 Systematic HVAC Diagnostics, Superheat/Subcooling & Airflow Troubleshooting 12.4 System Commissioning, Testing, Adjusting & Balancing (TAB)

7.3 Fuel Oil Heating Systems & Code-Compliant Fuel Gas Piping

Key Takeaways Explain This Topic AI

Fuel oil heating systems utilize No. 2 fuel oil (140,000 BTU/gal) atomized at high pressure (100 to 150 psig) through precision nozzles with specific flow ratings (GPH), spray angles (30° to 90°), and spray patterns (solid, hollow, semi-solid).

Oil burner primary safety controls utilize a cadmium sulfide (cad) cell to sense visible flame, which drops resistance from > 20,000 Ω in darkness to < 1,600 Ω (typically 300–800 Ω) under flame within a 15- to 45-second trial for ignition.

Stable oil burner combustion requires maintaining an overfire draft of -0.01 to -0.02 in. w.c. and a breeching stack draft of -0.04 to -0.06 in. w.c. regulated by a barometric draft control.

Fuel gas piping must be sized using the Longest Length Method from the meter or regulator to the furthest appliance, referencing approved capacity tables in the North Carolina Fuel Gas Code (IFGC Chapter 4 / NFPA 54).

Gas piping installations require code-mandated sediment traps (drip legs) minimum 3 inches deep at appliance inlets, accessible shutoff valves within 6 feet, dedicated CSST bonding (minimum 6 AWG copper), and pressure testing at not less than 1.5 times working pressure (minimum 3 psig for 10 minutes).

Last updated: August 2026

Fuel Oil Heating Systems & Code-Compliant Fuel Gas Piping

Quick Reference: No. 2 Fuel Oil has a heating value of 140 , 000 BTU/gallon 140,000\text{ BTU/gallon} 140 , 000 BTU/gallon and is atomized at 100 − 150 psig 100 - 150\text{ psig} 100 − 150 psig through precision nozzles rated in Gallons Per Hour ( G P H GPH GP H ). Flame sensing is performed by a Cadmium Sulfide (cad) cell whose resistance must drop below 1 , 600 Ω 1,600\ \Omega 1 , 600 Ω ( 300 − 800 Ω 300 - 800\ \Omega 300 − 800 Ω normal) during operation. Fuel gas piping systems are sized using the Longest Length Method per the North Carolina Fuel Gas Code (NCFGC) , require 3 in. 3\text{ in.} 3 in. sediment traps , and must be pressure tested at a minimum of 1.5 × working pressure 1.5\times\text{ working pressure} 1.5 × working pressure (minimum 3 psig 3\text{ psig} 3 psig for 10 minutes 10\text{ minutes} 10 minutes ). CSST systems require a dedicated 6 AWG copper bonding jumper .

1. Fuel Oil Properties & High-Pressure Atomization

Residential oil-fired heating equipment in North Carolina operates almost exclusively on Standard No. 2 Fuel Oil (ASTM D396), a middle distillate fuel similar to diesel.

Fuel Oil Property Specification / Benchmark Value Field Significance

Higher Heating Value 140 , 000 BTU/gallon 140,000\text{ BTU/gallon} 140 , 000 BTU/gallon ( 19 , 500 BTU/lb 19,500\text{ BTU/lb} 19 , 500 BTU/lb ) Universal benchmark for oil furnace input calculations

Minimum Flash Point 100 ∘ F 100^\circ\text{F} 10 0 ∘ F ( 38 ∘ C 38^\circ\text{C} 3 8 ∘ C ) (Typically 115 ∘ F − 140 ∘ F 115^\circ\text{F} - 140^\circ\text{F} 11 5 ∘ F − 14 0 ∘ F ) Temperature at which oil emits sufficient vapor to ignite; safe for storage

Auto-Ignition Temperature 500 ∘ F − 700 ∘ F 500^\circ\text{F} - 700^\circ\text{F} 50 0 ∘ F − 70 0 ∘ F ( 260 ∘ C − 371 ∘ C 260^\circ\text{C} - 371^\circ\text{C} 26 0 ∘ C − 37 1 ∘ C ) Temperature at which atomized oil combusts without external spark

Density / Specific Gravity 7.05 − 7.30 lbs/gallon 7.05 - 7.30\text{ lbs/gallon} 7.05 − 7.30 lbs/gallon (API Gravity 30 − 36 30 - 36 30 − 36 ) Heavier than water; high energy density per unit volume

Viscosity (Saybolt Universal) 32 − 38 SSU 32 - 38\text{ SSU} 32 − 38 SSU at 100 ∘ F 100^\circ\text{F} 10 0 ∘ F Affects atomization droplet size; cold oil increases droplet size

Pour Point − 10 ∘ F to 0 ∘ F -10^\circ\text{F} \text{ to } 0^\circ\text{F} − 1 0 ∘ F to 0 ∘ F Outdoor tanks in cold weather require kerosene (No. 1 oil) blending to prevent wax gelling

The High-Pressure Gun Burner Operating Cycle HIGH-PRESSURE GUN BURNER ANATOMY

  • +---------------------+ +---------------------+ +---------------------+
  • | Electric Motor |====> | Direct-Drive Fan |====> | Blast Tube Air |
  • | (3,450 RPM, 1/7 HP) | | Impeller (Air) | | & Retention Head |
  • +----------+----------+ +---------------------+ +----------+----------+
  • |
  • v |
  • +---------------------+ +---------------------+ |
  • | Fuel Oil Pump |====> | High-Pressure Pipe |===> [Nozzle] ===+===> (Ignited Flame)
  • | (100 - 150 psig) | | (with Cut-Off Valve)| |
  • +---------------------+ +---------------------+ |
  • |
  • +---------------------+ +---------------------+ |
  • | Ignition Transformer|====> | Spark Electrodes |=================+
  • | (10,000 - 20,000 V) | | (1/8" Gap, 10-20 kV)|
  • +---------------------+ +---------------------+

Motor & Blower: A 3 , 450 RPM 3,450\text{ RPM} 3 , 450 RPM motor drives both the combustion air squirrel-cage impeller and the direct-coupled high-pressure fuel pump.

Fuel Oil Pump: Draws oil from the supply tank through a 10 -micron 10\text{-micron} 10 -micron filter and pressurizes it to 100 to 150 psig 100\text{ to } 150\text{ psig} 100 to 150 psig (standard factory setting is 100 psig 100\text{ psig} 100 psig ; modern flame-retention burners frequently operate at 130 − 140 psig 130 - 140\text{ psig} 130 − 140 psig to improve atomization).

Precision Atomizing Nozzle: Forces pressurized liquid oil through tiny tangential swirl slots into a swirl chamber, spinning the oil at high velocity before ejecting it through a microscopic orifice. This breaks the liquid stream into a fine mist of billions of microscopic droplets ( 10 to 50 μ m 10\text{ to } 50\ \mu\text{m} 10 to 50 μ m diameter), dramatically expanding surface area for rapid vaporization.

Nozzle Designations & Spray Patterns:

Flow Rate ( G P H GPH GP H ): Rated in Gallons Per Hour at standard 100 psig 100\text{ psig} 100 psig inlet pressure.

Spray Angle: Available in 30 ∘ , 45 ∘ , 60 ∘ , 70 ∘ , 80 ∘ , 30^\circ, 45^\circ, 60^\circ, 70^\circ, 80^\circ, 3 0 ∘ , 4 5 ∘ , 6 0 ∘ , 7 0 ∘ , 8 0 ∘ , and 90 ∘ 90^\circ 9 0 ∘ . Sized to match the length and width of the combustion chamber.

Spray Pattern Types:

Hollow Cone (Type A / H): Droplets concentrated on the outer cone perimeter; ideal for smaller firing rates ( < 1.0 GPH < 1.0\text{ GPH} < 1.0 GPH ) and round or compact combustion chambers.

Solid Cone (Type B / S): Droplets distributed evenly throughout the entire cone; ideal for larger firing rates and long, rectangular combustion chambers.

Semi-Solid / Universal (Type W / SS): Uniform distribution transitioning from solid at low flow to hollow at higher flow; versatile replacement nozzle.

Nozzle Firing Rate Adjustment Formula

When pump operating pressure ( P actual P_{\text{actual}} P actual ​ ) is adjusted away from the standard 100 psig 100\text{ psig} 100 psig test rating, the actual firing rate in GPH and BTU/hr changes according to the square root law: GPH actual = GPH rated × P actual 100 \text{GPH}_{\text{actual}} = \text{GPH}_{\text{rated}} \times \sqrt{\frac{P_{\text{actual}}}{100}} GPH actual ​ = GPH rated ​ × 100 P actual ​ ​ ​ Input Firing Rate (BTU/hr) = GPH actual × 140 , 000 BTU/gal \text{Input Firing Rate (BTU/hr)} = \text{GPH}_{\text{actual}} \times 140,000\text{ BTU/gal} Input Firing Rate (BTU/hr) = GPH actual ​ × 140 , 000 BTU/gal

Worked Example: Oil Firing Rate at Elevated Pump Pressure

A technician installs a 0.75 GPH 0.75\text{ GPH} 0.75 GPH nozzle in a modern flame-retention burner and adjusts the oil pump discharge pressure to 144 psig 144\text{ psig} 144 psig to improve atomization:

Calculate Actual Fuel Delivery Rate: GPH actual = 0.75 × 144 100 = 0.75 × 1.44 = 0.75 × 1.20 = 0.90 GPH \text{GPH}_{\text{actual}} = 0.75 \times \sqrt{\frac{144}{100}} = 0.75 \times \sqrt{1.44} = 0.75 \times 1.20 = 0.90\text{ GPH} GPH actual ​ = 0.75 × 100 144 ​ ​ = 0.75 × 1.44 ​ = 0.75 × 1.20 = 0.90 GPH

Calculate Total Heat Input: Input Capacity = 0.90 GPH × 140 , 000 BTU/gal = 126 , 000 BTU/hr \text{Input Capacity} = 0.90\text{ GPH} \times 140,000\text{ BTU/gal} = 126,000\text{ BTU/hr} Input Capacity = 0.90 GPH × 140 , 000 BTU/gal = 126 , 000 BTU/hr

  • 2. Electrodes, Cad Cell Flame Safety & Draft Regulation
  • Ignition Electrodes & Flame Retention Heads

Ignition Transformer / Solid-State Igniter: Steps line voltage ( 120 VAC 120\text{ VAC} 120 VAC ) up to 10 , 000 to 20 , 000 VAC 10,000\text{ to } 20,000\text{ VAC} 10 , 000 to 20 , 000 VAC across two heavy nichrome/tungsten electrode tips. On modern burners, intermittent ignition energizes the spark only during the initial 10 − 15 seconds 10 - 15\text{ seconds} 10 − 15 seconds of ignition.

Electrode Settings (Standard Beckett 'F' / 'AFG' Head):

Gap between electrode tips: 1 / 8 inch 1/8\text{ inch} 1/8 inch ( 3.2 mm 3.2\text{ mm} 3.2 mm ).

Height above nozzle centerline: 1 / 4 inch 1/4\text{ inch} 1/4 inch ( 6.4 mm 6.4\text{ mm} 6.4 mm ).

Forward position ahead of nozzle face: 1 / 16 inch 1/16\text{ inch} 1/16 inch ( 1.6 mm 1.6\text{ mm} 1.6 mm ).

Critical Rule: Electrodes must never touch the oil spray cone, which causes carbon buildup, spark distortion, and flame failure.

Flame Retention Head: Aerodynamically shaped stainless steel swirl baffle that creates a localized low-pressure recirculation zone at the blast tube tip. This anchors the flame firmly to the burner head, generating flame temperatures 500 ∘ F 500^\circ\text{F} 50 0 ∘ F hotter than older non-retention burners and eliminating combustion pulsation.

Cad Cell Primary Safety Controls

The primary safety control on an oil burner utilizes a Cadmium Sulfide (cad) photocell to optically verify flame presence: CAD CELL RESISTANCE & SAFETY TIMING

  • [DARKNESS / IDLE STATE] [NORMAL OPERATING FLAME]
  • (Cad Cell Senses No Light) (Cad Cell Senses Yellow Flame)
  • |
  • v |
  • Resistance: > 20,000 Ohms v
  • (Typically > 100,000 Ohms) Resistance: < 1,600 Ohms
  • | (Normal Range: 300 - 800 Ohms)
  • v |
  • Primary Control Safety Switch: v
  • Permits 15 - 45 sec Trial for Ignition Primary Control Holds Circuit Closed;
  • | Burner Continues Steady Operation
  • +---> (If Flame Fails to Ignite)
  • |
  • v
  • [HARD LOCKOUT]
  • (Requires Manual Pushbutton Reset)

Photoconductive Cad Cell Physics: Cadmium sulfide is a semiconductor that decreases electrical resistance when exposed to visible light (specifically yellow light emitted by burning oil).

Diagnostic Resistance Values:

In Total Darkness (Burner Off): > 20 , 000 Ω > 20,000\ \Omega > 20 , 000 Ω (typically 100 , 000 − 500 , 000 Ω 100,000 - 500,000\ \Omega 100 , 000 − 500 , 000 Ω ).

Under Normal Bright Flame: < 1 , 600 Ω < 1,600\ \Omega < 1 , 600 Ω (benchmark target: 300 to 800 Ω 300\text{ to } 800\ \Omega 300 to 800 Ω ).

Failing / Dirty Cell: 1 , 600 − 5 , 000 Ω 1,600 - 5,000\ \Omega 1 , 600 − 5 , 000 Ω (causes intermittent safety lockouts).

Safety Lockout Timing: If the cad cell does not sense flame and drop below 1 , 600 Ω 1,600\ \Omega 1 , 600 Ω within 15 , 30 , or 45 seconds 15\text{, } 30\text{, or } 45\text{ seconds} 15 , 30 , or 45 seconds (depending on control model, standard: 15 seconds 15\text{ seconds} 15 seconds on modern microprocessor controls), the primary control locks out on safety, cutting all power to the motor and oil valve to prevent unburned oil from flooding the hot combustion chamber.

Draft Dynamics & Barometric Draft Regulators

Unlike induced-draft gas furnaces, standard oil appliances depend on chimney stack effect to pull combustion products through the heat exchanger:

Overfire Draft (Combustion Chamber): Must be maintained between − 0.01 and − 0.02 in. w.c. -0.01\text{ and } -0.02\text{ in. w.c.} − 0.01 and − 0.02 in. w.c. (negative pressure).

Breeching / Stack Draft (Flue Pipe): Typically − 0.04 to − 0.06 in. w.c. -0.04\text{ to } -0.06\text{ in. w.c.} − 0.04 to − 0.06 in. w.c.

Barometric Draft Regulator: A balanced, counterweighted swinging damper installed in the flue pipe. As outdoor winds or chimney temperatures increase stack draft, the damper swings open, pulling basement/room air into the chimney to relieve excess suction and keep overfire draft stable at − 0.02 in. w.c. -0.02\text{ in. w.c.} − 0.02 in. w.c.

Combustion Smoke Test: Measured using a Bacharach Smoke Tester (drawing 10 full strokes of flue gas through filter paper). North Carolina code and NFPA 31 target a #0 to Trace #1 smoke spot with a minimum CO 2 \text{CO}_2 CO 2 ​ concentration of 10.0 % − 12.5 % 10.0\% - 12.5\% 10.0% − 12.5% .

3. Code-Compliant Fuel Gas Piping Materials & Prohibitions (NCFGC / NFPA 54)

The North Carolina Fuel Gas Code (Chapter 4) and NFPA 54 regulate the materials, joining methods, sizing, and routing of natural gas and LP piping systems.

Approved Fuel Gas Piping Materials

Piping Material Standard / Specification Allowable Applications & Code Restrictions

Black Steel Pipe ASTM A53 / ASTM A106, Schedule 40 Standard for indoor and above-ground gas distribution; threaded with malleable iron fittings

Galvanized Steel Pipe ASTM A53, Schedule 40 Permitted indoors and outdoors where gas contains < 0.3 grains H 2 S / 100 ft 3 < 0.3\text{ grains H}_2\text{S} / 100\text{ ft}^3 < 0.3 grains H 2 ​ S /100 ft 3

Corrugated Stainless Steel (CSST) ANSI LC 1 / CSA 6.26 Flexible indoor routing; requires dedicated electrical bonding (see CSST rules below)

Copper / Brass Tubing ASTM B88 (Type K or L), ASTM B280 Permitted only where gas contains < 0.3 grains hydrogen sulfide / 100 cu ft < 0.3\text{ grains hydrogen sulfide} / 100\text{ cu ft} < 0.3 grains hydrogen sulfide /100 cu ft ; brazed fittings ( > 1 , 000 ∘ F > 1,000^\circ\text{F} > 1 , 00 0 ∘ F )

Polyethylene (PE) Plastic Pipe ASTM D2513 Underground ONLY, outside of building footprints ; minimum 18 in. 18\text{ in.} 18 in. burial depth ( 24 in. 24\text{ in.} 24 in. under driveways); requires yellow AWG 18 tracer wire

Prohibited Fuel Gas Piping Locations:

Gas piping must NEVER be installed inside or through a supply or return air duct, clothes chute, chimney, gas vent, dumbwaiter shaft, or elevator shaft.

Piping must not be run concealed inside hollow masonry walls or embedded in solid concrete without approved sleeve conduits vented to the outdoors.

Unions and bushings are prohibited in concealed locations (all concealed joints must be welded, threaded couplings, or approved press-connect fittings).

4. Corrugated Stainless Steel Tubing (CSST) & Electrical Bonding Mandates

Corrugated Stainless Steel Tubing (CSST) offers rapid, flexible installation but is vulnerable to electrical arcing perforation from indirect lightning strikes: CSST DIRECT ELECTRICAL BONDING SYSTEM

  • Gas Piping System Building Electrical System
  • +-------------------------+ +----------------------------------+
  • | Black Iron / Brass CSST | | Electrical Service Grounding |
  • | Manifold or Fitting | | Electrode System (GES) |
  • +------------+------------+ +-----------------+----------------+
  • | |
  • +=======(Minimum 6 AWG Bare/Insulated Copper Wire)====+
  • | (Direct Clamp-Type Grounding Connector) |
  • | (Maximum 75 Feet Total Conductor Length) |

NCFGC Section 310 & NFPA 54 CSST Bonding Rules:

Bonding Conductor Sizing: Minimum 6 AWG bare or insulated copper wire .

Attachment Point: Connected directly to the steel piping manifold, rigid pipe upstream of CSST, or a manufacturer-approved brass CSST transition fitting. Must never clamp directly onto the corrugated stainless tubing wall .

Termination Point: Bonded directly to the building's electrical service grounding electrode system (ground rod, ground ring, or building steel) or service panel ground bus.

Maximum Length: The bonding conductor run must not exceed 75 feet 75\text{ feet} 75 feet ( 22.9 m 22.9\text{ m} 22.9 m ) total length and must remain as straight as practical.

Arc-Resistant CSST (Black Jacket / Conductive Shield): Systems listed to ANSI LC 1 / CSA 6.26 (e.g., FlashShield, CounterStrike) with an arc-resistant conductive jacket that meets the criteria of ICC-ES PMG-1024 are exempt from the additional 6 AWG direct bonding requirement and may rely on the standard equipment grounding conductor of the connected appliance.

5. Gas Pipe Sizing: The Longest Length Method

Under the North Carolina Fuel Gas Code (Section 402), fuel gas piping must be engineered to deliver adequate volumetric flow ( C F H CFH CF H ) to all connected appliances without exceeding a design pressure drop of 0.5 in. w.c. 0.5\text{ in. w.c.} 0.5 in. w.c. ( 125 Pa 125\text{ Pa} 125 Pa ) for standard low-pressure systems ( < 0.5 psig < 0.5\text{ psig} < 0.5 psig ). Natural gas flow demand is determined by: CFH = Total Appliance BTU/hr Input / 1 , 000 BTU/cu ft \text{CFH} = \text{Total Appliance BTU/hr Input} / 1,000\text{ BTU/cu ft} CFH = Total Appliance BTU/hr Input /1 , 000 BTU/cu ft . THE LONGEST LENGTH SIZING PROTOCOL

  • [Gas Meter / Regulator]
  • |
  • |================== (Main Trunk Line) ==================+
  • | |
  • [Branch A] [Branch B]
  • | |
  • (Furnace: 100k) (Water Heater: 40k)
  • Distance: 30 ft Distance: 60 ft (CRITICAL PATH)
  • *Rule:* The entire system (Main Trunk, Branch A, and Branch B) MUST be sized using the
  • 60-foot column values from the NCFGC pipe capacity tables!*

Step-by-Step Longest Length Sizing Procedure:

Determine Longest Length: Measure the total physical distance from the gas meter (or LP second-stage regulator) to the most hydraulically remote appliance in the entire building. This single distance establishes the governing table column for every segment in the piping system.

Calculate Demand per Section: For each pipe section (main trunk and individual branch runs), calculate the maximum gas demand in Cubic Feet per Hour ( C F H CFH CF H ) carried by that specific segment.

Select Table Column: In the NCFGC Schedule 40 Metallic Pipe Table ( 0.60 0.60 0.60 specific gravity, 0.5 in. w.c. 0.5\text{ in. w.c.} 0.5 in. w.c. drop, < 0.5 psig < 0.5\text{ psig} < 0.5 psig inlet), locate the column corresponding to the measured longest length (or next higher length if exact distance is not listed).

Size Each Section: Follow down that single column to find a capacity equal to or greater than the segment's required C F H CFH CF H . Read the required nominal pipe diameter in the left-hand column.

Standard Pipe Capacity Reference (NCFGC Table 402.4(1) — Natural Gas, 0.5 in. wc Drop, 0.60 SG)

Nominal Pipe Size (in.) 10 ft 20 ft 30 ft 40 ft 50 ft 60 ft 70 ft 80 ft 100 ft 125 ft

1/2" 172 CFH 172\text{ CFH} 172 CFH 118 CFH 118\text{ CFH} 118 CFH 95 CFH 95\text{ CFH} 95 CFH 81 CFH 81\text{ CFH} 81 CFH 72 CFH 72\text{ CFH} 72 CFH 65 CFH 65\text{ CFH} 65 CFH 60 CFH 60\text{ CFH} 60 CFH 56 CFH 56\text{ CFH} 56 CFH 50 CFH 50\text{ CFH} 50 CFH 44 CFH 44\text{ CFH} 44 CFH

3/4" 360 CFH 360\text{ CFH} 360 CFH 247 CFH 247\text{ CFH} 247 CFH 199 CFH 199\text{ CFH} 199 CFH 170 CFH 170\text{ CFH} 170 CFH 151 CFH 151\text{ CFH} 151 CFH 137 CFH 137\text{ CFH} 137 CFH 126 CFH 126\text{ CFH} 126 CFH 117 CFH 117\text{ CFH} 117 CFH 104 CFH 104\text{ CFH} 104 CFH 92 CFH 92\text{ CFH} 92 CFH

1" 678 CFH 678\text{ CFH} 678 CFH 466 CFH 466\text{ CFH} 466 CFH 374 CFH 374\text{ CFH} 374 CFH 320 CFH 320\text{ CFH} 320 CFH 284 CFH 284\text{ CFH} 284 CFH 257 CFH 257\text{ CFH} 257 CFH 237 CFH 237\text{ CFH} 237 CFH 220 CFH 220\text{ CFH} 220 CFH 195 CFH 195\text{ CFH} 195 CFH 173 CFH 173\text{ CFH} 173 CFH

1-1/4" 1 , 390 CFH 1,390\text{ CFH} 1 , 390 CFH 957 CFH 957\text{ CFH} 957 CFH 768 CFH 768\text{ CFH} 768 CFH 657 CFH 657\text{ CFH} 657 CFH 583 CFH 583\text{ CFH} 583 CFH 528 CFH 528\text{ CFH} 528 CFH 486 CFH 486\text{ CFH} 486 CFH 452 CFH 452\text{ CFH} 452 CFH 400 CFH 400\text{ CFH} 400 CFH 355 CFH 355\text{ CFH} 355 CFH

1-1/2" 2 , 090 CFH 2,090\text{ CFH} 2 , 090 CFH 1 , 430 CFH 1,430\text{ CFH} 1 , 430 CFH 1 , 150 CFH 1,150\text{ CFH} 1 , 150 CFH 985 CFH 985\text{ CFH} 985 CFH 873 CFH 873\text{ CFH} 873 CFH 791 CFH 791\text{ CFH} 791 CFH 728 CFH 728\text{ CFH} 728 CFH 677 CFH 677\text{ CFH} 677 CFH 600 CFH 600\text{ CFH} 600 CFH 532 CFH 532\text{ CFH} 532 CFH

2" 4 , 020 CFH 4,020\text{ CFH} 4 , 020 CFH 2 , 760 CFH 2,760\text{ CFH} 2 , 760 CFH 2 , 220 CFH 2,220\text{ CFH} 2 , 220 CFH 1 , 900 CFH 1,900\text{ CFH} 1 , 900 CFH 1 , 680 CFH 1,680\text{ CFH} 1 , 680 CFH 1 , 520 CFH 1,520\text{ CFH} 1 , 520 CFH 1 , 400 CFH 1,400\text{ CFH} 1 , 400 CFH 1 , 300 CFH 1,300\text{ CFH} 1 , 300 CFH 1 , 160 CFH 1,160\text{ CFH} 1 , 160 CFH 1 , 020 CFH 1,020\text{ CFH} 1 , 020 CFH

Worked Example: Sizing a Two-Appliance Residential System

A gas piping system has a gas meter feeding a main trunk. Branch 1 serves a 100 , 000 BTU/hr 100,000\text{ BTU/hr} 100 , 000 BTU/hr furnace located 30 ft 30\text{ ft} 30 ft from the meter. Branch 2 serves a 40 , 000 BTU/hr 40,000\text{ BTU/hr} 40 , 000 BTU/hr water heater located 60 ft 60\text{ ft} 60 ft from the meter.

Determine Longest Length: Longest run is to the water heater = 60 ft 60\text{ ft} 60 ft . Use the 60 ft 60\text{ ft} 60 ft column for all sizing.

Size Main Trunk (Meter to Branch Split):

Total Load = 100 , 000 + 40 , 000 = 140 , 000 BTU/hr = 140 CFH 100,000 + 40,000 = 140,000\text{ BTU/hr} = 140\text{ CFH} 100 , 000 + 40 , 000 = 140 , 000 BTU/hr = 140 CFH .

Looking down the 60 ft 60\text{ ft} 60 ft column: 1 / 2 " 1/2" 1/2" pipe carries 65 CFH 65\text{ CFH} 65 CFH (too small); 3 / 4 " 3/4" 3/4" pipe carries 137 CFH 137\text{ CFH} 137 CFH (too small for 140 CFH 140\text{ CFH} 140 CFH ); 1 " pipe 1"\text{ pipe} 1" pipe carries 257 CFH 257\text{ CFH} 257 CFH . Main trunk must be 1 " nominal steel pipe 1"\text{ nominal steel pipe} 1" nominal steel pipe .

Size Branch 1 (Furnace Run):

Load = 100 , 000 BTU/hr = 100 CFH 100,000\text{ BTU/hr} = 100\text{ CFH} 100 , 000 BTU/hr = 100 CFH .

Looking down the 60 ft 60\text{ ft} 60 ft column: 3 / 4 " 3/4" 3/4" pipe carries 137 CFH ≥ 100 CFH 137\text{ CFH} \ge 100\text{ CFH} 137 CFH ≥ 100 CFH . Branch 1 must be 3 / 4 " nominal steel pipe 3/4"\text{ nominal steel pipe} 3/4" nominal steel pipe .

Size Branch 2 (Water Heater Run):

Load = 40 , 000 BTU/hr = 40 CFH 40,000\text{ BTU/hr} = 40\text{ CFH} 40 , 000 BTU/hr = 40 CFH .

Looking down the 60 ft 60\text{ ft} 60 ft column: 1 / 2 " 1/2" 1/2" pipe carries 65 CFH ≥ 40 CFH 65\text{ CFH} \ge 40\text{ CFH} 65 CFH ≥ 40 CFH . Branch 2 must be 1 / 2 " nominal steel pipe 1/2"\text{ nominal steel pipe} 1/2" nominal steel pipe .

6. Installation Details, Sediment Traps & Pressure Testing CODE-COMPLIANT GAS APPLIANCE CONNECTION (NCFGC)

  • Rigid Gas Supply Pipe
  • |
  • v
  • +-------------------+
  • | Manual Shutoff | (Within 6 feet of appliance, same room, accessible)
  • | Ball Valve |
  • +---------+---------+
  • |
  • v
  • +-------------------+
  • | Flexible Metallic | (ANSI Z21.24, max 6 feet, cannot penetrate cabinet)
  • | Connector |
  • +---------+---------+
  • |
  • +----------------------------+
  • | |
  • v v
  • +-------------------+ +-------------------+
  • | Directional Tee |======> | Appliance Gas |
  • | Fitting | | Control Valve |
  • +---------+---------+ +-------------------+
  • |
  • v (Gas changes direction 90°; dirt drops into pocket)
  • +-------------------+
  • | Sediment Trap |
  • | (Nipple min 3") |
  • +---------+---------+
  • |
  • v
  • +-------------------+
  • | Threaded Pipe Cap |
  • +-------------------+

Key Code Installation Rules (NCFGC Chapter 4):

Sediment Trap (Drip Leg):

Must be installed at the inlet of all automatic gas appliances downstream of the equipment shutoff valve.

Must be configured using a tee fitting with a capped nipple extending down a minimum of 3 inches 3\text{ inches} 3 inches ( 76 mm 76\text{ mm} 76 mm ) to trap pipe scale, rust, and moisture before it reaches the gas valve.

Gas must flow through the run or turn into the branch such that debris drops vertically into the dead-end nipple.

Exceptions: Illuminating appliances, ranges, clothes dryers, outdoor grills, and decorative vented fireplaces are exempt.

Appliance Shutoff Valves:

Must be installed upstream of the appliance connector and sediment trap.

Must be located in the same room as the appliance, within 6 feet 6\text{ feet} 6 feet ( 1 , 829 mm 1,829\text{ mm} 1 , 829 mm ) of the appliance inlet, and readily accessible.

Flexible Appliance Connectors (ANSI Z21.24):

Maximum length: 6 feet 6\text{ feet} 6 feet ( 1.8 m 1.8\text{ m} 1.8 m ) for domestic ranges, dryers, and furnaces.

Prohibited from extending through walls, floors, ceilings, partitions, or appliance housing casings.

Pipe Support Spacing:

1 / 2 " 1/2" 1/2" pipe: Support every 6 feet 6\text{ feet} 6 feet .

3 / 4 " − 1 " 3/4" - 1" 3/4" − 1" pipe: Support every 8 feet 8\text{ feet} 8 feet .

1 − 1 / 4 " 1-1/4" 1 − 1/4" and larger: Support every 10 feet 10\text{ feet} 10 feet .

CSST tubing: Support every 4 to 6 feet 4\text{ to } 6\text{ feet} 4 to 6 feet .

Code Pressure Testing Requirements (NCFGC Section 406):

Test Pressure: Not less than 1.5 times 1.5\text{ times} 1.5 times the maximum working pressure, but in no case less than 3 psig 3\text{ psig} 3 psig ( 20.6 kPa 20.6\text{ kPa} 20.6 kPa gauge).

Standard Field Test Practice: Residential low-pressure systems in North Carolina are typically tested at 10 to 15 psig 10\text{ to } 15\text{ psig} 10 to 15 psig on a calibrated diaphragm or mercury manometer gauge.

Test Duration: Minimum 10 minutes 10\text{ minutes} 10 minutes for residential systems (commercial systems require 30 to 60 minutes 30\text{ to } 60\text{ minutes} 30 to 60 minutes ). No drop in test gauge pressure is permitted.

Test Medium: Air, nitrogen, or carbon dioxide. NEVER test with pure oxygen , which will cause an explosive detonation when contacting residual oil or pipe dope!

Appliance Isolation: All appliance shutoff valves must be closed, and appliance control valves disconnected/capped during test pressures exceeding 0.5 psig 0.5\text{ psig} 0.5 psig ( 14 in. w.c. 14\text{ in. w.c.} 14 in. w.c. ) to prevent destroying the delicate rubber diaphragms in internal appliance regulators.

Loading diagram... Fuel Gas Piping Sizing (Longest Length Method) & Code Installation Flowchart

Cad Cell Electrical Resistance (Ohms) Across Operating States