Study guide

9.3 Boiler Trim, Expansion Tanks, Air Elimination & Safety Controls

North Carolina HVAC Contractor License Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: North Carolina HVAC Licensing Framework & Board Jurisprudence

1.1 NC Dual-Board Regulatory Structure & General Statutes 1.2 Heating Classifications, Groups & Scopes 1.3 Examination Prerequisites, Qualifier Responsibilities & Disciplinary Rules 1.4 Examination Logistics, Reference Books & Code Editions

2 Chapter 2: North Carolina Business Organizations, Contracts & Lien Law

2.1 Construction Contracts, Project Management & Bidding 2.2 North Carolina Mechanics' Lien Law & Bond Claims 2.3 Business Organizations, Financial Management & Taxation

3 Chapter 3: Construction Safety, Electrical Safety & EPA 608

3.1 OSHA 1926 Construction Safety & Job Site Protocols 3.2 Electrical Safety, NFPA 70E & Lockout/Tagout (LOTO) 3.3 EPA Section 608 & Refrigerant Transition Regulations

4 Chapter 4: Thermodynamics, Refrigeration Cycle & Psychrometrics

4.1 Fundamentals of Thermodynamics & Heat Transfer 4.2 The Mechanical Refrigeration Cycle & Component Dynamics 4.3 Psychrometric Properties, Air Processes & Chart Navigation

5 Chapter 5: ACCA Manual J & Manual N Load Calculations

5.1 Manual J Design Conditions & Thermal Parameters 5.2 Fenestration, Opaque Envelope & Internal Heat Gains 5.3 Infiltration, Duct Losses & Total Block Load Synthesis 5.4 ACCA Manual N Commercial Load Calculation

6 Chapter 6: ACCA Manual D & Manual Q Duct Design & Air Distribution

6.1 Fan Laws, Airflow Dynamics & Total External Static Pressure 6.2 ACCA Manual D Sizing Protocol & Friction Rate Calculation 6.3 SMACNA Duct Construction, Fittings & Air Balancing 6.4 ACCA Manual Q Commercial Low-Pressure Duct Design

7 Chapter 7: Forced Air Heating, Gas Furnaces & Fuel Piping

7.1 Natural Gas & Propane Combustion Fundamentals 7.2 Gas Furnace Operation, Sequence of Control & Diagnostics 7.3 Fuel Oil Heating Systems & Code-Compliant Fuel Gas Piping

8 Chapter 8: Heat Pumps, Inverters & Commercial System Selection (Manual CS)

8.1 Heat Pump Operating Principles, Reversing Valves & Physics 8.2 Defrost Controls, Supplemental Electric Heat & Balance Points 8.3 Inverter Mini-Splits & Variable Refrigerant Flow (VRF) Systems 8.4 Manual CS: Commercial Applications, Systems & Equipment

9 Chapter 9: Hydronic Heating, Steam Systems & Boilers (H1)

9.1 Hydronic Fundamentals, Boiler Classifications & Steam Systems 9.2 Hydronic Piping Layouts, Circulator Pumps & Head Loss Calculations 9.3 Boiler Trim, Expansion Tanks, Air Elimination & Safety Controls 9.4 The NC Uniform Boiler & Pressure Vessel Act (H1 Reference)

10 Chapter 10: Commercial Refrigeration & NC Board Regulations

10.1 NC State Board of Refrigeration Contractors Statutes & Licensure 10.2 Commercial Refrigeration Systems, Multiplex Racks & Defrost Protocols 10.3 Walk-In Coolers, Freezers, Evaporator Pressure Regulators & Valves

11 Chapter 11: NC Administration, Mechanical, Fuel Gas & Energy Codes

11.1 North Carolina Mechanical Code: Equipment Access, Clearances & Condensate 11.2 Ventilation Rates, Exhaust Systems & Duct Smoke Detection 11.3 NC Fuel Gas Code: Combustion Air, Venting & Gas Appliance Installation 11.4 NC Energy Conservation Code: Duct Testing, Envelope & Efficiency Standards 11.5 NC Administrative Code & Policies: Permits, Inspections & Plan Review

12 Chapter 12: Electrical Fundamentals, Motor Controls & Diagnostics

12.1 HVAC Electrical Fundamentals, Circuit Schematics & Power Distribution 12.2 Electric Motors, Capacitors & Motor Controls 12.3 Systematic HVAC Diagnostics, Superheat/Subcooling & Airflow Troubleshooting 12.4 System Commissioning, Testing, Adjusting & Balancing (TAB)

9.3 Boiler Trim, Expansion Tanks, Air Elimination & Safety Controls

Key Takeaways Explain This Topic AI

ASME Section IV and NC Mechanical Code mandate an ASME-rated pressure relief valve on every boiler (typically set to 30 psig for low-pressure hot water; 15 psig for steam) with full-size, unvalved metallic discharge piping terminating 2 to 6 inches above the floor drain.

The Point of No Pressure Change (PONPC) occurs where the expansion tank connects to the piping; installing the circulator pump immediately downstream pumping away from the PONPC ensures positive system pressure throughout all zones.

Diaphragm expansion tanks must be pre-charged with air to match the system cold static fill pressure (typically 12 psig) while disconnected from water pressure; a ruptured bladder causes a waterlogged tank and relief valve weeping.

Low Water Cut-Offs (LWCO) are mandatory safety controls on all steam boilers and hot water boilers rated above 400,000 BTU/hr under ASME CSD-1 and NC Mechanical Code to shut down the burner during low-water emergencies.

Henry's Law dictates that dissolved air releases from water at high temperatures and low pressures, requiring high-efficiency microbubble air separators installed directly at the boiler supply outlet where water is hottest.

Last updated: August 2026

Boiler Trim, Expansion Tanks, Air Elimination & Safety Controls

Safety Mandate: Boiler trim encompasses the operational and limit safety devices installed directly on or immediately adjacent to a boiler vessel. Under ASME Boiler and Pressure Vessel Code Section IV , ASME CSD-1 (Controls and Safety Devices for Automatically Fired Boilers), and Chapter 10 of the North Carolina Mechanical Code (NCMC) , these safety controls protect building occupants from catastrophic pressure explosions, thermal runaway, and dry-fire burnouts.

Mandatory ASME Boiler Trim & Safety Devices +-----------------------------------------------------------------------------------+

  • | MANDATORY ASME BOILER TRIM MATRIX |
  • +-----------------------------------------------------------------------------------+
  • | Device Name | Hot Water Boilers (Section IV) | Steam Boilers (Sec IV) |
  • |-----------------------------+---------------------------------+--------------------------|
  • | Pressure Relief Valve (PRV) | ASME "HV" Rated (Set @ 30 psig) | ASME "V" (Set @ 15 psig) |
  • | High Limit Safety Cut-Off | Aquastat (Manual Reset ≤ 240°F) | Pressuretrol (Man Reset) |
  • | Low Water Cut-Off (LWCO) | Mandatory (> 400 MBH or inst.) | Mandatory (All Boilers) |
  • | Primary Operating Control | Modulating/Operating Aquastat | Operating Pressuretrol |
  • | System Gauge | Tridicator (PSI, Feet, °F) | Steam Gauge + Pigtail |
  • | Water Gauge Glass & Cocks | Not Applicable | Mandatory (Visual Level) |
  • +-----------------------------------------------------------------------------------+
  • 1. ASME Pressure Relief Valves (PRVs)

The Pressure Relief Valve is the ultimate mechanical safety device protecting the boiler vessel against over-pressurization.

Set Pressure: Standard residential low-pressure hot water boilers are equipped with a 30 psig 30\text{ psig} 30 psig relief valve. Low-pressure steam boilers are equipped with a 15 psig 15\text{ psig} 15 psig safety relief valve.

Discharge Capacity: The relief valve must carry an ASME national board rating with a steam/BTU discharge capacity equal to or greater than the maximum gross output capacity ( M B H MBH MB H ) of the boiler burner.

NCMC Discharge Piping Installation Rules:

Discharge pipe diameter must equal the full nominal size of the valve outlet (never reduced in size).

Must be constructed of rigid metallic pipe approved for water distribution (copper, galvanized steel, black iron, or CPVC rated for 210 ∘ F 210^\circ\text{F} 21 0 ∘ F ; PVC is strictly prohibited).

Must pitch downward to drain by gravity with no traps or dips where water could accumulate and freeze.

Discharge end must terminate unthreaded between 2 and 6 inches 2\text{ and }6\text{ inches} 2 and 6 inches above the floor drain or approved waste receptacle.

Strict Prohibition: No shutoff valve, stopcock, or restrictive fitting of any kind is permitted between the boiler and the relief valve, nor in the discharge pipe.

2. Low Water Cut-Off (LWCO) Controls

A Low Water Cut-Off shuts off electrical power to the fuel burner when the water level inside the boiler drops below a safe operating threshold, preventing dry-fire meltdowns and steam explosions.

Code Requirements (ASME CSD-1 & NCMC 1007):

Mandatory on all steam boilers regardless of size.

Mandatory on all hot water boilers with heat input exceeding 400 , 000 BTU/hr 400,000\text{ BTU/hr} 400 , 000 BTU/hr ( 400 MBH 400\text{ MBH} 400 MBH ) , or any boiler installed above the level of the lowest radiation/distribution piping.

Commercial boilers ( > 400 MBH > 400\text{ MBH} > 400 MBH ) typically require two independent LWCOs: a primary automatic-reset LWCO and a secondary manual-reset LWCO .

LWCO Operating Mechanisms:

Electronic Probe Type: Utilizes an insulated stainless steel sensor probe inserted into the boiler shell or supply riser. Uses water conductivity ( > 20 microSiemens > 20\text{ microSiemens} > 20 microSiemens ) to complete a low-voltage AC electrical circuit to ground. If water drops below the probe tip, the circuit opens, cutting power to the burner ignition module within seconds.

Float Type: Uses a mechanical brass float inside a float chamber with an external magnetic switch. Requires weekly physical blowdown testing to flush sediment out of the bowl.

3. Temperature & Pressure Limit Controls (Aquastats & Pressuretrols)

High Limit Aquastat (Hot Water): Set higher than the operating control (typically 200 ∘ F − 220 ∘ F 200^\circ\text{F} - 220^\circ\text{F} 20 0 ∘ F − 22 0 ∘ F , max allowable 240 ∘ F 240^\circ\text{F} 24 0 ∘ F ). If operating controls fail and temperature spikes, the high limit breaks the 24 V 24\text{V} 24 V burner circuit. Under NCMC, modern installations require a manual-reset lockout.

Operating vs. High Limit Pressuretrol (Steam):

Operating Pressuretrol: Operates steam boiler on pressure differential (e.g., Cut-in at 0.5 psig 0.5\text{ psig} 0.5 psig , Cut-out at 2.0 psig 2.0\text{ psig} 2.0 psig ).

Manual-Reset High Limit: Set at 5 to 10 psig 5\text{ to }10\text{ psig} 5 to 10 psig (well below the 15 psig 15\text{ psig} 15 psig relief valve setting) to shut down the burner before the relief valve discharges.

Steam Pigtail Siphon Tube: A steam pressure gauge and pressuretrol must always be mounted on a 180 ∘ or 360 ∘ 180^\circ\text{ or }360^\circ 18 0 ∘ or 36 0 ∘ pigtail siphon loop . Steam condenses inside the loop, creating a liquid water seal that protects the sensitive brass bourdon tube and internal bellows from high-temperature live steam destruction.

4. Pressure/Temperature Indicators (Tridicators & Water Columns)

Tridicator (Hot Water Boilers): A triple-scale combination gauge displaying: (1) System pressure in psig \text{psig} psig , (2) Altitude/static head in feet of water \text{feet of water} feet of water ( 1 psi = 2.31 ft 1\text{ psi} = 2.31\text{ ft} 1 psi = 2.31 ft ), and (3) Water temperature in ∘ F ^\circ\text{F} ∘ F .

Water Gauge Glass (Steam Boilers): Heavy borosilicate glass tube connected via brass gauge cocks to the boiler water column, displaying the exact liquid water meniscus relative to the Normal Water Line (NWL).

The Point of No Pressure Change (PONPC) & Pumping Away

The single most important hydraulic concept in hydronic piping design is the Point of No Pressure Change (PONPC) , established by the connection point of the expansion tank. +-----------------------------------------------------------------------------------+

  • | THE POINT OF NO PRESSURE CHANGE (PONPC) |
  • +-----------------------------------------------------------------------------------+
  • | The expansion tank contains a fixed cushion of air separated by a diaphragm. |
  • | Because air is compressible and water is incompressible, the circulator pump |
  • | CANNOT alter the pressure at the expansion tank connection point while running. |
  • | Therefore, the expansion tank connection IS the Point of No Pressure Change. |

+-----------------------------------------------------------------------------------+ Comparison: Pumping Away vs. Pumping Toward the PONPC

  • 1. RECOMMENDED: "PUMPING AWAY"
  • [Boiler] ---> [Air Separator / PONPC / Expansion Tank] ---> [Circulator PUMP] ---> [Zone Baseboards]
  • Static Pressure: 12 psig
  • Pump Dynamic Head: +6 psig
  • Operating System Pressure: 12 + 6 = 18 psig (Pressure increases throughout all zones)
  • Result: Air stays dissolved in water; automatic vents work perfectly; no cavitation.
  • 2. REJECTED: "PUMPING TOWARD"
  • [Circulator PUMP] ---> [Boiler] ---> [Air Separator / PONPC / Expansion Tank] ---> [Zone Baseboards]
  • Static Pressure: 12 psig
  • Pump Suction Pressure: 12 - 6 = 6 psig (Pressure drops on pump inlet / top floor)
  • Result: In tall buildings, pressure drops below atmospheric (< 0 psig), drawing air into vents

and causing pump impeller cavitation and upper-floor air binding.

Why "Pumping Away" is the Modern Standard

Preventing Pump Cavitation: When a circulator pumps away from the PONPC, the full dynamic head developed by the pump impeller is added to the static fill pressure throughout the distribution piping. The suction port stays at stable static fill pressure ( 12 psig 12\text{ psig} 12 psig ), well above the vapor pressure of hot water, completely eliminating cavitation.

Preventing Air Ingestion: If a pump is installed pumping toward the boiler (pumping toward the PONPC), the pump must drop its suction pressure to create flow. On upper floors of multi-story buildings, pressure can drop below atmospheric ( < 0 psig < 0\text{ psig} < 0 psig ), sucking room air in through automatic air vents and air-binding radiators.

Hydronic Expansion Tanks: Physics & Sizing

Water expands in volume when heated. Between 50 ∘ F 50^\circ\text{F} 5 0 ∘ F and 180 ∘ F 180^\circ\text{F} 18 0 ∘ F , water volume expands by approximately 3.0 % 3.0\% 3.0% to 4.0 % 4.0\% 4.0% . Because water is incompressible, heating closed-system water without an expansion vessel causes hydraulic pressure to spike instantly to 30 psig 30\text{ psig} 30 psig , blowing the relief valve. +-----------------------------------------------------------------------------------+

  • | EXPANSION TANK ARCHITECTURES |
  • +-----------------------------------------------------------------------------------+
  • | 1. Open Expansion Tank (Historic): Vented to atmosphere, located above highest |
  • | radiator in attic. Subject to continuous evaporation, corrosion, and freezing. |
  • | 2. Plain Steel Compression Tank (Conventional): Airtight steel cylinder suspended |
  • | from basement ceiling. Air cushion directly contacts water surface. Prone to |
  • | air absorption into water over time, becoming "waterlogged". |
  • | 3. Pre-charged Diaphragm / Bladder Tank (Modern): Heavy-duty butyl rubber membrane|
  • | permanently separates factory-pressurized nitrogen/air chamber from water. |
  • +-----------------------------------------------------------------------------------+
  • Diaphragm Tank Sizing Formula (ASME Method)

The required total acceptance volume ( V t V_t V t ​ ) for a pre-pressurized diaphragm expansion tank is calculated using the system water volume and pressure boundaries: V t = V s ⋅ e 1 − ( P fill, absolute P relief, absolute ) V_t = V_s \cdot \frac{e}{1 - \left( \frac{P_{\text{fill, absolute}}}{P_{\text{relief, absolute}}} \right)} V t ​ = V s ​ ⋅ 1 − ( P relief, absolute ​ P fill, absolute ​ ​ ) e ​

Where:

V t V_t V t ​ = Total expansion tank volume ( gallons \text{gallons} gallons )

V s V_s V s ​ = Total water volume of the entire hydronic system (boiler + piping + emitters, gallons \text{gallons} gallons )

e e e = Net thermal expansion coefficient of water between fill temp ( 50 ∘ F 50^\circ\text{F} 5 0 ∘ F ) and operating temp ( 180 ∘ F 180^\circ\text{F} 18 0 ∘ F ): e ≈ 0.0285 e \approx 0.0285 e ≈ 0.0285 for 180 ∘ F 180^\circ\text{F} 18 0 ∘ F ( 0.032 0.032 0.032 for 200 ∘ F 200^\circ\text{F} 20 0 ∘ F )

P fill, absolute P_{\text{fill, absolute}} P fill, absolute ​ = Cold static fill pressure absolute ( P fill (psig) + 14.7 P_{\text{fill (psig)}} + 14.7 P fill (psig) ​ + 14.7 , psia \text{psia} psia )

P relief, absolute P_{\text{relief, absolute}} P relief, absolute ​ = Maximum allowable working pressure absolute at tank ( P relief (psig) − 5 psi safety buffer + 14.7 P_{\text{relief (psig)}} - 5\text{ psi safety buffer} + 14.7 P relief (psig) ​ − 5 psi safety buffer + 14.7 , psia \text{psia} psia )

Expansion Tank Pre-Charge & Waterlogging Diagnostics

Pre-Charge Rule: The air charge inside a diaphragm expansion tank must be checked with an accurate tire pressure gauge and adjusted to equal the system cold fill pressure (typically 12 psig 12\text{ psig} 12 psig ) BEFORE the tank is connected to the water piping (or with system water pressure relieved to 0 psig 0\text{ psig} 0 psig ).

Waterlogged Tank Symptom: If the internal diaphragm ruptures, water fills the air chamber. Because liquid cannot compress, system pressure spikes rapidly from 12 psig 12\text{ psig} 12 psig to 30 psig 30\text{ psig} 30 psig as soon as the burner fires, causing the ASME relief valve to discharge water onto the floor during every heating cycle.

Air Elimination & Deaeration Dynamics

Entrained air and dissolved microbubbles in a hydronic system cause baseboard gurgling noise, corrosion, reduced heat transfer, and pump cavitation.

Henry's Law of Gas Solubility

Henry's Law states that the amount of dissolved gas in a liquid is directly proportional to pressure and inversely proportional to temperature: Gas Solubility ∝ Fluid Pressure Fluid Temperature \text{Gas Solubility} \propto \frac{\text{Fluid Pressure}}{\text{Fluid Temperature}} Gas Solubility ∝ Fluid Temperature Fluid Pressure ​

Cold Water Fill ( 50 ∘ F 50^\circ\text{F} 5 0 ∘ F , 12 psig 12\text{ psig} 12 psig ): Absorbs high concentrations of dissolved atmospheric nitrogen and oxygen.

Heated Water ( 180 ∘ F 180^\circ\text{F} 18 0 ∘ F at Boiler Outlet): Liquid can no longer hold dissolved gases in solution; microbubbles instantly precipitate out of the water.

Air Separation Technologies Air Elimination Evolution

├── 1. In-Line Air Scoop: Cast iron body with internal deflector baffle; catches large bubbles only (50% efficiency)

├── 2. Tangential / Centrifugal Separator: Uses vortex swirling action to separate air in commercial mechanical rooms

└── 3. Microbubble Coalescing Separator (e.g., Spirovent): Dense copper wire mesh matrix coalesces microscopic

bubbles into larger bubbles that rise to top automatic float vent (99.9% air removal including dissolved gases)

Optimal Installation Location: The air separator must always be installed at the point of highest water temperature and lowest pressure —which is directly at the boiler supply outlet nozzle immediately before the circulator pump suction (the PONPC) .

Automatic Water Make-Up & Backflow Prevention +-----------------------------------------------------------------------------------+

  • | WATER FEED & BACKFLOW ASSEMBLY |
  • +-----------------------------------------------------------------------------------+
  • | Potable Cold Water Supply ---> [Shutoff] ---> [ASSE 1012/1013 Backflow Preventer] |
  • | ---> [Fast-Fill Pressure Reducing Valve (12 psig)] |
  • | ---> [Boiler Return / Near-Boiler Header] |
  • +-----------------------------------------------------------------------------------+
  • Cold Static Fill Pressure Calculation

The automatic Pressure Reducing Valve (PRV / water feeder) maintains a constant static pressure in the system when cold, ensuring positive pressure at the highest heat emitter: P fill = ( H highest × 0.433 psi/ft ) + P cushion P_{\text{fill}} = (H_{\text{highest}} \times 0.433\text{ psi/ft}) + P_{\text{cushion}} P fill ​ = ( H highest ​ × 0.433 psi/ft ) + P cushion ​

Where:

H highest H_{\text{highest}} H highest ​ = Vertical elevation height from the boiler/feeder to the top of the highest radiator ( feet \text{feet} feet )

0.433 psi/ft 0.433\text{ psi/ft} 0.433 psi/ft = Hydrostatic head pressure exerted by water ( 1 / 2.31 ft/psi 1 / 2.31\text{ ft/psi} 1/2.31 ft/psi )

P cushion P_{\text{cushion}} P cushion ​ = Minimum positive pressure cushion required at the top radiator vent to prevent vacuum air ingestion ( 4.0 to 5.0 psig 4.0\text{ to }5.0\text{ psig} 4.0 to 5.0 psig )

Standard Residential Example: For a 2-story residence ( H = 18 ft H = 18\text{ ft} H = 18 ft ): P fill = ( 18 ft × 0.433 psi/ft ) + 4.2 psi = 7.79 + 4.2 = 12.0 psig P_{\text{fill}} = (18\text{ ft} \times 0.433\text{ psi/ft}) + 4.2\text{ psi} = 7.79 + 4.2 = \mathbf{12.0\text{ psig}} P fill ​ = ( 18 ft × 0.433 psi/ft ) + 4.2 psi = 7.79 + 4.2 = 12.0 psig

Backflow Prevention Standards (NCMC & NC Plumbing Code)

Because closed hydronic heating loops contain chemically treated water, stale stagnant fluid, and potential glycol solutions, a cross-connection to the building's potable drinking water is hazardous:

Standard Residential (No Chemicals): ASSE 1012 Dual Check Valve with intermediate atmospheric vent.

Commercial / Glycol Systems: ASSE 1013 Reduced Pressure Zone (RPZ) backflow preventer assembly with test cocks and relief port, inspected annually.

  • Step-by-Step Worked Technical Examples
  • Example 1: Diaphragm Expansion Tank Sizing

Problem: A multi-zone residential hydronic heating system has a total water volume ( V s V_s V s ​ ) of 75 gallons 75\text{ gallons} 75 gallons . The system operates at a design temperature of 180 ∘ F 180^\circ\text{F} 18 0 ∘ F ( e = 0.0285 e = 0.0285 e = 0.0285 ). The cold static fill pressure is set to 12 psig 12\text{ psig} 12 psig , and the boiler is protected by a standard 30 psig 30\text{ psig} 30 psig ASME relief valve. Calculate the minimum required total tank volume ( V t V_t V t ​ ) for a pre-charged diaphragm expansion tank (using a 5 psi 5\text{ psi} 5 psi operating safety margin below relief setting).

Solution:

Calculate Absolute Pressures: P fill, abs = 12 psig + 14.7 = 26.7 psia P_{\text{fill, abs}} = 12\text{ psig} + 14.7 = 26.7\text{ psia} P fill, abs ​ = 12 psig + 14.7 = 26.7 psia P max, operating = 30 psig (relief) − 5 psi = 25 psig P_{\text{max, operating}} = 30\text{ psig (relief)} - 5\text{ psi} = 25\text{ psig} P max, operating ​ = 30 psig (relief) − 5 psi = 25 psig P relief, abs = 25 psig + 14.7 = 39.7 psia P_{\text{relief, abs}} = 25\text{ psig} + 14.7 = 39.7\text{ psia} P relief, abs ​ = 25 psig + 14.7 = 39.7 psia

Calculate Acceptance Pressure Factor ( A f A_f A f ​ ): A f = 1 − ( P fill, abs P relief, abs ) = 1 − ( 26.7 39.7 ) = 1 − 0.6725 = 0.3275 A_f = 1 - \left( \frac{P_{\text{fill, abs}}}{P_{\text{relief, abs}}} \right) = 1 - \left( \frac{26.7}{39.7} \right) = 1 - 0.6725 = 0.3275 A f ​ = 1 − ( P relief, abs ​ P fill, abs ​ ​ ) = 1 − ( 39.7 26.7 ​ ) = 1 − 0.6725 = 0.3275

Calculate Expansion Tank Total Volume ( V t V_t V t ​ ): V t = V s ⋅ e A f = 75 gal × 0.0285 0.3275 = 75 × 0.08702 = 6.53 gallons V_t = V_s \cdot \frac{e}{A_f} = 75\text{ gal} \times \frac{0.0285}{0.3275} = 75 \times 0.08702 = \mathbf{6.53\text{ gallons}} V t ​ = V s ​ ⋅ A f ​ e ​ = 75 gal × 0.3275 0.0285 ​ = 75 × 0.08702 = 6.53 gallons

(Select the next standard commercial diaphragm tank size, such as an Extrol Model #30 with 7.4 gal 7.4\text{ gal} 7.4 gal total capacity).

Example 2: Static Cold Fill Pressure for a 3-Story Commercial Building

Problem: A commercial hydronic heating boiler is located in the basement. The highest radiator convector is located on the third floor, 36 feet 36\text{ feet} 36 feet above the boiler pressure reducing fill valve. Calculate the minimum cold static fill pressure setting ( P fill P_{\text{fill}} P fill ​ ) required on the water feed valve, maintaining a 4.5 psig 4.5\text{ psig} 4.5 psig cushion at the top convector.

Solution:

Calculate Hydrostatic Head Pressure: P head = 36 ft × 0.433 psi/ft = 15.588 psig P_{\text{head}} = 36\text{ ft} \times 0.433\text{ psi/ft} = 15.588\text{ psig} P head ​ = 36 ft × 0.433 psi/ft = 15.588 psig

Add Top Cushion Pressure: P fill = P head + P cushion = 15.588 psig + 4.5 psig = 20.09 ≈ 20.0 psig P_{\text{fill}} = P_{\text{head}} + P_{\text{cushion}} = 15.588\text{ psig} + 4.5\text{ psig} = \mathbf{20.09} \approx \mathbf{20.0\text{ psig}} P fill ​ = P head ​ + P cushion ​ = 15.588 psig + 4.5 psig = 20.09 ≈ 20.0 psig

(The expansion tank pre-charge pressure must also be increased to 20.0 psig 20.0\text{ psig} 20.0 psig while disconnected from the system).

Example 3: Low Water Cut-Off (LWCO) Code Compliance Verification

Problem: An HVAC contractor is bidding on replacing an atmospheric commercial hot water boiler rated at 650 , 000 BTU/hr 650,000\text{ BTU/hr} 650 , 000 BTU/hr ( 650 MBH 650\text{ MBH} 650 MBH ) input in an office building. The boiler supplies rooftop air handler hydronic coils located 25 feet 25\text{ feet} 25 feet above the boiler room floor.

Identify all mandatory ASME CSD-1 and NC Mechanical Code requirements regarding: (1) Low Water Cut-Off requirements, (2) Relief valve capacity rating, and (3) Relief valve discharge termination.

Solution:

LWCO Mandates: Because input exceeds 400 , 000 BTU/hr 400,000\text{ BTU/hr} 400 , 000 BTU/hr and the heat emitters are located above the boiler, Low Water Cut-Off protection is strictly mandatory . Under ASME CSD-1, the installation requires two controls: a primary automatic-reset LWCO and an independent secondary manual-reset LWCO wired in series with the burner safety circuit.

Relief Valve Capacity: The ASME Section IV relief valve must have a certified steam/heat relieving capacity ≥ 650 MBH \ge 650\text{ MBH} ≥ 650 MBH (or the gross output rating of the boiler) set at a maximum of 30 psig 30\text{ psig} 30 psig (or system design pressure ≤ 160 psig \le 160\text{ psig} ≤ 160 psig ).

Discharge Termination: Full-size metallic pipe terminating unthreaded between 2 and 6 inches 2\text{ and }6\text{ inches} 2 and 6 inches above the floor drain with no intermediate shut-off valves.

Loading diagram... Complete Near-Boiler Trim Piping Architecture with 'Pumping Away' from PONPC