Study guide

4.2 The Mechanical Refrigeration Cycle & Component Dynamics

North Carolina HVAC Contractor License Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: North Carolina HVAC Licensing Framework & Board Jurisprudence

1.1 NC Dual-Board Regulatory Structure & General Statutes 1.2 Heating Classifications, Groups & Scopes 1.3 Examination Prerequisites, Qualifier Responsibilities & Disciplinary Rules 1.4 Examination Logistics, Reference Books & Code Editions

2 Chapter 2: North Carolina Business Organizations, Contracts & Lien Law

2.1 Construction Contracts, Project Management & Bidding 2.2 North Carolina Mechanics' Lien Law & Bond Claims 2.3 Business Organizations, Financial Management & Taxation

3 Chapter 3: Construction Safety, Electrical Safety & EPA 608

3.1 OSHA 1926 Construction Safety & Job Site Protocols 3.2 Electrical Safety, NFPA 70E & Lockout/Tagout (LOTO) 3.3 EPA Section 608 & Refrigerant Transition Regulations

4 Chapter 4: Thermodynamics, Refrigeration Cycle & Psychrometrics

4.1 Fundamentals of Thermodynamics & Heat Transfer 4.2 The Mechanical Refrigeration Cycle & Component Dynamics 4.3 Psychrometric Properties, Air Processes & Chart Navigation

5 Chapter 5: ACCA Manual J & Manual N Load Calculations

5.1 Manual J Design Conditions & Thermal Parameters 5.2 Fenestration, Opaque Envelope & Internal Heat Gains 5.3 Infiltration, Duct Losses & Total Block Load Synthesis 5.4 ACCA Manual N Commercial Load Calculation

6 Chapter 6: ACCA Manual D & Manual Q Duct Design & Air Distribution

6.1 Fan Laws, Airflow Dynamics & Total External Static Pressure 6.2 ACCA Manual D Sizing Protocol & Friction Rate Calculation 6.3 SMACNA Duct Construction, Fittings & Air Balancing 6.4 ACCA Manual Q Commercial Low-Pressure Duct Design

7 Chapter 7: Forced Air Heating, Gas Furnaces & Fuel Piping

7.1 Natural Gas & Propane Combustion Fundamentals 7.2 Gas Furnace Operation, Sequence of Control & Diagnostics 7.3 Fuel Oil Heating Systems & Code-Compliant Fuel Gas Piping

8 Chapter 8: Heat Pumps, Inverters & Commercial System Selection (Manual CS)

8.1 Heat Pump Operating Principles, Reversing Valves & Physics 8.2 Defrost Controls, Supplemental Electric Heat & Balance Points 8.3 Inverter Mini-Splits & Variable Refrigerant Flow (VRF) Systems 8.4 Manual CS: Commercial Applications, Systems & Equipment

9 Chapter 9: Hydronic Heating, Steam Systems & Boilers (H1)

9.1 Hydronic Fundamentals, Boiler Classifications & Steam Systems 9.2 Hydronic Piping Layouts, Circulator Pumps & Head Loss Calculations 9.3 Boiler Trim, Expansion Tanks, Air Elimination & Safety Controls 9.4 The NC Uniform Boiler & Pressure Vessel Act (H1 Reference)

10 Chapter 10: Commercial Refrigeration & NC Board Regulations

10.1 NC State Board of Refrigeration Contractors Statutes & Licensure 10.2 Commercial Refrigeration Systems, Multiplex Racks & Defrost Protocols 10.3 Walk-In Coolers, Freezers, Evaporator Pressure Regulators & Valves

11 Chapter 11: NC Administration, Mechanical, Fuel Gas & Energy Codes

11.1 North Carolina Mechanical Code: Equipment Access, Clearances & Condensate 11.2 Ventilation Rates, Exhaust Systems & Duct Smoke Detection 11.3 NC Fuel Gas Code: Combustion Air, Venting & Gas Appliance Installation 11.4 NC Energy Conservation Code: Duct Testing, Envelope & Efficiency Standards 11.5 NC Administrative Code & Policies: Permits, Inspections & Plan Review

12 Chapter 12: Electrical Fundamentals, Motor Controls & Diagnostics

12.1 HVAC Electrical Fundamentals, Circuit Schematics & Power Distribution 12.2 Electric Motors, Capacitors & Motor Controls 12.3 Systematic HVAC Diagnostics, Superheat/Subcooling & Airflow Troubleshooting 12.4 System Commissioning, Testing, Adjusting & Balancing (TAB)

4.2 The Mechanical Refrigeration Cycle & Component Dynamics

Key Takeaways Explain This Topic AI

The mechanical vapor-compression refrigeration cycle operates across four primary components: the compressor (pressure and temperature rise), condenser (desuperheating, condensing, subcooling), metering device (isenthalpic pressure drop), and evaporator (boiling and superheating).

Refrigerant mass flow rate is governed by system capacity divided by Net Refrigerating Effect: Refrigerant Mass Flow Rate = Capacity / NRE = (Tons × 12,000) / (h1 - h4) in lbs/hr.

Thermostatic Expansion Valves (TXVs) maintain constant evaporator superheat by balancing sensing bulb opening pressure (P1) against evaporator closing pressure (P2) and internal spring closing pressure (P3), requiring external equalization whenever evaporator pressure drop exceeds 2.5 psi.

Total Heat of Rejection (THR = NRE + Wc) represents the combined thermal energy absorbed in the evaporator plus the heat of compression, all of which must be discharged across the condenser coil.

Modern A2L mildly flammable refrigerants (such as R-454B and R-32) require strict adherence to ASHRAE Standard 15 and 34 safety protocols, liquid charging procedures to prevent fractionation from temperature glide, and specialized leak mitigation.

Last updated: August 2026

The Mechanical Refrigeration Cycle & Component Dynamics

System Architecture: The vapor-compression refrigeration cycle is a continuous closed thermodynamic loop that absorbs heat from a low-temperature conditioned space and discharges it to a higher-temperature ambient environment. The system is physically divided into two pressure zones ( High Side and Low Side ) and two state zones ( Vapor and Liquid ).

The Four Fundamental Components of the Refrigeration Cycle +-----------------------------------------------------------------------------------+

  • | THE FOUR MECHANICAL REFRIGERATION CYCLE COMPONENTS |
  • +-----------------------------------------------------------------------------------+
  • | 1. COMPRESSOR (Vapor Pump): Low-P / Low-T Vapor --> High-P / High-T Vapor |
  • | 2. CONDENSER (Heat Rejector): High-P / High-T Vapor --> High-P Subcooled Liquid |
  • | 3. METERING DEVICE (Pressure Divider): High-P Liquid --> Low-P Liquid/Vapor Mix |
  • | 4. EVAPORATOR (Heat Absorber): Low-P Liquid/Vapor --> Low-P Superheated Vapor |
  • +-----------------------------------------------------------------------------------+
  • 1. The Compressor (Heart of the System)

The compressor functions as a vapor pump, drawing low-pressure, low-temperature superheated vapor from the suction line and compressing it into high-pressure, superheated discharge gas.

Function: Raises refrigerant pressure and saturation temperature above the ambient temperature of the condensing medium (air or water), enabling spontaneous heat rejection.

Compression Ratio ( C R CR CR ): The ratio of absolute discharge pressure to absolute suction pressure: Compression Ratio ( C R ) = P discharge, absolute P suction, absolute = P head (psig) + 14.7 P suction (psig) + 14.7 \text{Compression Ratio } (CR) = \frac{P_{\text{discharge, absolute}}}{P_{\text{suction, absolute}}} = \frac{P_{\text{head (psig)}} + 14.7}{P_{\text{suction (psig)}} + 14.7} Compression Ratio ( CR ) = P suction, absolute ​ P discharge, absolute ​ ​ = P suction (psig) ​ + 14.7 P head (psig) ​ + 14.7 ​ Diagnostic Rule: High compression ratios ( > 10 : 1 > 10:1 > 10 : 1 in comfort cooling) drastically reduce compressor volumetric efficiency ( η v \eta_v η v ​ ), elevate discharge temperatures above 225 ∘ F 225^\circ\text{F} 22 5 ∘ F , accelerate oil breakdown, and cause premature motor winding failure.

Compressor Geometries:

Scroll Compressors: Utilize two interleaved Archimedean spirals (one stationary, one orbiting) to compress gas continuously without suction/discharge valves. Offer high isentropic efficiency, continuous flow, and high tolerance to liquid droplet compliance.

Reciprocating Compressors: Utilize pistons and reed valves within cylinders. Subject to valve flutter and clearance volume re-expansion losses.

Rotary & Screw Compressors: High-efficiency positive displacement units used in ductless mini-splits and large commercial chillers.

2. The Condenser (Heat Rejection Exchanger)

The condenser removes thermal energy from the superheated discharge gas and discharges it into the cooling medium (ambient air or cooling tower water). The condensation process occurs across three distinct thermal zones:

Desuperheating (Zone 1 - Sensible Cooling): Hot discharge gas ( 160 ∘ F − 200 ∘ F 160^\circ\text{F} - 200^\circ\text{F} 16 0 ∘ F − 20 0 ∘ F ) enters the condenser and cools down sensibly to its saturation temperature (e.g., 115 ∘ F 115^\circ\text{F} 11 5 ∘ F for R-410A at 390 psig 390\text{ psig} 390 psig ).

Condensing (Zone 2 - Latent Heat Rejection): Saturated vapor changes phase to saturated liquid at constant condensing pressure and constant saturation temperature, releasing its latent heat of vaporization.

Subcooling (Zone 3 - Sensible Cooling of Liquid): Once completely condensed, the liquid refrigerant is cooled sensibly below its saturated condensing temperature (typically 8 ∘ F 8^\circ\text{F} 8 ∘ F to 15 ∘ F 15^\circ\text{F} 1 5 ∘ F of subcooling in modern high-efficiency systems). Subcooling = T condensing saturation − T liquid line measured \text{Subcooling} = T_{\text{condensing saturation}} - T_{\text{liquid line measured}} Subcooling = T condensing saturation ​ − T liquid line measured ​

Important

Subcooling provides two critical benefits: (1) It guarantees that a solid column of 100% liquid refrigerant reaches the expansion device without flashing into premature vapor across liquid line vertical rises or filter-driers, and (2) Each 1 ∘ F 1^\circ\text{F} 1 ∘ F of subcooling increases system net refrigerating capacity by approximately 0.5 % 0.5\% 0.5% to 0.7 % 0.7\% 0.7% .

3. The Metering Device (Expansion Mechanism)

The metering device (expansion valve, capillary tube, or fixed orifice) acts as the thermodynamic dividing line between the high-pressure and low-pressure sides of the system.

Thermodynamic Process: Isenthalpic Throttling ( h 3 = h 4 h_3 = h_4 h 3 ​ = h 4 ​ ). No external work is performed and no heat is transferred ( Q = 0 , W = 0 Q = 0, W = 0 Q = 0 , W = 0 ).

Flash Gas Generation: As subcooled high-pressure liquid drops abruptly in pressure, its saturation temperature falls below the entering liquid temperature. A portion of the liquid (typically 15 % 15\% 15% to 25 % 25\% 25% by mass) instantly vaporizes ("flashes"). The latent heat absorbed to vaporize this flash gas cools the remaining 75 % 75\% 75% to 85 % 85\% 85% of liquid down to the evaporator saturation temperature (e.g., 40 ∘ F 40^\circ\text{F} 4 0 ∘ F ).

Metering Device Types & TXV Force Equilibrium

Device Type Modulation Method Charging Diagnostic Method Typical HVAC Application

Fixed Orifice / Piston Constant opening area; flow varies directly with pressure differential Superheat Method (Target Superheat Chart) Basic residential split AC systems

Capillary Tube Fixed length/diameter copper tube; high friction pressure drop Critical Charge Weight (Weighed to ± 0.5 oz \pm 0.5\text{ oz} ± 0.5 oz ) Domestic refrigerators, window units, PTACs

Thermostatic Expansion Valve (TXV) Modulates pin opening via thermal sensing bulb to maintain constant superheat Subcooling Method (Manufacturer nameplate target) High-efficiency heat pumps, commercial split systems

Electronic Expansion Valve (EEV) Stepper motor driven (0-500 steps) modulated by microprocessor PID controller Digital electronic diagnostics / Subcooling Inverter heat pumps, VRF systems, precision chillers

TXV Mechanics & Force Balance

A Thermostatic Expansion Valve maintains a constant evaporator superheat by continuously balancing three internal forces acting on its flexible diaphragm: P 1 = P 2 + P 3 P_1 = P_2 + P_3 P 1 ​ = P 2 ​ + P 3 ​

P 1 P_1 P 1 ​ (Opening Force): Vapor pressure generated by the remote sensing bulb mounted on the suction line, exerting downward force on top of the diaphragm.

P 2 P_2 P 2 ​ (Closing Force): Evaporator inlet pressure acting upward against the bottom of the diaphragm.

P 3 P_3 P 3 ​ (Closing Force): Adjustable mechanical spring pressure acting upward against the bottom of the diaphragm.

Internal vs. External Equalization

Internal Equalizer: Senses evaporator pressure directly at the valve outlet. Permissible only on single-circuit evaporator coils with negligible refrigerant pressure drop ( < 2.5 psi < 2.5\text{ psi} < 2.5 psi ).

External Equalizer: Utilizes an external 1/4" sensing line connected to the suction line downstream of the sensing bulb. Mandatory on multi-circuit coils utilizing refrigerant distributors or any evaporator where internal coil pressure drop exceeds 2.5 psi 2.5\text{ psi} 2.5 psi for high-pressure refrigerants (R-410A) or 1.5 psi 1.5\text{ psi} 1.5 psi for low-pressure systems. An internal equalizer on a high-drop coil would sense artificially high pressure, forcing the valve prematurely closed and starving the coil.

4. The Evaporator (Heat Absorption Exchanger)

The evaporator absorbs heat from the conditioned air or water stream, transforming the cold low-pressure liquid-vapor mixture into superheated vapor.

Boiling Zone (Latent Heat Absorption): Liquid refrigerant boils at constant saturation temperature (e.g., 40 ∘ F 40^\circ\text{F} 4 0 ∘ F at 118 psig 118\text{ psig} 118 psig for R-410A), absorbing latent heat from indoor room air passing over the coil fins.

Superheating Zone (Sensible Heating): Once all liquid has vaporized (at the "dry-out point"), the remaining cold vapor absorbs sensible heat along the final passes of the coil: Superheat = T suction line measured − T evaporating saturation \text{Superheat} = T_{\text{suction line measured}} - T_{\text{evaporating saturation}} Superheat = T suction line measured ​ − T evaporating saturation ​

Target Airflow: Standard comfort air conditioning systems require 400 CFM per ton 400\text{ CFM per ton} 400 CFM per ton ( ± 10 % \pm 10\% ± 10% ). Reduced airflow ( < 350 CFM/ton < 350\text{ CFM/ton} < 350 CFM/ton ) drops evaporator saturation temperature below 32 ∘ F 32^\circ\text{F} 3 2 ∘ F , leading to coil frost formation, severe capacity loss, and liquid floodback.

Pressure-Enthalpy ( P P P - h h h ) Mollier Diagram Analysis

The Pressure-Enthalpy diagram graphical chart represents the complete thermodynamic state of a refrigerant across all cycle stages. Pressure (P)

  • ^ CRITICAL POINT
  • | /\
  • | / \
  • | SUBCOOLED / \ SUPERHEATED
  • | LIQUID / \ VAPOR
  • | REGION / TWO- \ REGION
  • | / PHASE \
  • P_high |-----------------(3)---------(2) Constant Condensing Pressure
  • | | | SATURATED| \
  • | | | MIXTURE | \
  • | | | DOME | \
  • P_low |-----------------(4)---------(1) Constant Evaporating Pressure
  • | / \
  • | / Saturated \ Saturated
  • | / Liquid Line \ Vapor Line
  • +----------------------------------------------------> Enthalpy (h) [BTU/lb]
  • <--- NRE --->
  • (h1 - h4)
  • The Four Thermodynamic State Changes on the P P P - h h h Diagram

State 1 → \rightarrow → State 2: Isentropic Compression ( 1 → 2 1 \rightarrow 2 1 → 2 )

Superheated vapor at evaporator outlet ( h 1 h_1 h 1 ​ , P low P_{\text{low}} P low ​ ) is compressed to high-pressure discharge gas ( h 2 h_2 h 2 ​ , P high P_{\text{high}} P high ​ ) along lines of constant entropy ( s = constant s = \text{constant} s = constant ).

Work of Compression ( W c W_c W c ​ ): W c = h 2 − h 1 ( BTU/lb ) W_c = h_2 - h_1 \quad (\text{BTU/lb}) W c ​ = h 2 ​ − h 1 ​ ( BTU/lb )

State 2 → \rightarrow → State 3: Isobaric Heat Rejection / Condensation ( 2 → 3 2 \rightarrow 3 2 → 3 )

High-pressure gas desuperheats, condenses, and subcools at constant condensing pressure ( P high P_{\text{high}} P high ​ ), exiting as subcooled liquid at enthalpy h 3 h_3 h 3 ​ .

Total Heat of Rejection ( T H R THR T H R ): T H R = h 2 − h 3 = ( h 2 − h 1 ) + ( h 1 − h 4 ) = W c + N R E ( BTU/lb ) THR = h_2 - h_3 = (h_2 - h_1) + (h_1 - h_4) = W_c + NRE \quad (\text{BTU/lb}) T H R = h 2 ​ − h 3 ​ = ( h 2 ​ − h 1 ​ ) + ( h 1 ​ − h 4 ​ ) = W c ​ + NRE ( BTU/lb )

State 3 → \rightarrow → State 4: Isenthalpic Expansion ( 3 → 4 3 \rightarrow 4 3 → 4 )

High-pressure subcooled liquid expands through the metering device to low evaporating pressure ( P low P_{\text{low}} P low ​ ) at constant enthalpy (vertical downward drop on P P P - h h h chart): h 4 = h 3 h_4 = h_3 h 4 ​ = h 3 ​

State 4 → \rightarrow → State 1: Isobaric Heat Absorption / Evaporation ( 4 → 1 4 \rightarrow 1 4 → 1 )

Low-pressure mixture boils and superheats at constant evaporating pressure ( P low P_{\text{low}} P low ​ ), absorbing building heat until exiting at enthalpy h 1 h_1 h 1 ​ .

Net Refrigerating Effect ( N R E NRE NRE ): N R E = h 1 − h 4 ( BTU/lb ) NRE = h_1 - h_4 \quad (\text{BTU/lb}) NRE = h 1 ​ − h 4 ​ ( BTU/lb )

Thermodynamic Governing Equations & System Metrics

1. Net Refrigerating Effect ( N R E NRE NRE ) N R E = h 1 − h 4 = h 1 − h 3 ( BTU/lb ) NRE = h_1 - h_4 = h_1 - h_3 \quad (\text{BTU/lb}) NRE = h 1 ​ − h 4 ​ = h 1 ​ − h 3 ​ ( BTU/lb )

2. Refrigerant Mass Flow Rate ( m ˙ \dot{m} m ˙ ) Refrigerant Mass Flow Rate ( m ˙ ) = System Capacity (BTU/hr) NRE (BTU/lb) = Tons × 12 , 000 h 1 − h 4 ( lbs/hr ) \text{Refrigerant Mass Flow Rate } (\dot{m}) = \frac{\text{System Capacity (BTU/hr)}}{\text{NRE (BTU/lb)}} = \frac{\text{Tons} \times 12,000}{h_1 - h_4} \quad (\text{lbs/hr}) Refrigerant Mass Flow Rate ( m ˙ ) = NRE (BTU/lb) System Capacity (BTU/hr) ​ = h 1 ​ − h 4 ​ Tons × 12 , 000 ​ ( lbs/hr )

3. Total Heat of Rejection ( T H R THR T H R Rate) Total Heat of Rejection (BTU/hr) = m ˙ × ( h 2 − h 3 ) = Capacity (BTU/hr) + [ Compressor Power (kW) × 3 , 412.14 ] \text{Total Heat of Rejection (BTU/hr)} = \dot{m} \times (h_2 - h_3) = \text{Capacity (BTU/hr)} + [\text{Compressor Power (kW)} \times 3,412.14] Total Heat of Rejection (BTU/hr) = m ˙ × ( h 2 ​ − h 3 ​ ) = Capacity (BTU/hr) + [ Compressor Power (kW) × 3 , 412.14 ]

4. Coefficient of Performance ( C O P COP COP ) & Energy Efficiency Ratio ( E E R EER EER ) COP = Refrigeration Output Work Input = h 1 − h 4 h 2 − h 1 = N R E W c \text{COP} = \frac{\text{Refrigeration Output}}{\text{Work Input}} = \frac{h_1 - h_4}{h_2 - h_1} = \frac{NRE}{W_c} COP = Work Input Refrigeration Output ​ = h 2 ​ − h 1 ​ h 1 ​ − h 4 ​ ​ = W c ​ NRE ​ EER = 3.41214 × COP = System Capacity (BTU/hr) Total Electrical Power (Watts) \text{EER} = 3.41214 \times \text{COP} = \frac{\text{System Capacity (BTU/hr)}}{\text{Total Electrical Power (Watts)}} EER = 3.41214 × COP = Total Electrical Power (Watts) System Capacity (BTU/hr) ​

Refrigerant Piping Design & Velocity Dynamics

Proper refrigerant line sizing is critical for ensuring reliable compressor lubrication and preventing excessive pressure drop capacity loss:

Suction Line Sizing Criteria:

Pressure Drop Limit: Maximum allowable pressure drop corresponds to a 2 ∘ F 2^\circ\text{F} 2 ∘ F saturation temperature drop (approximately 2.0 psi 2.0\text{ psi} 2.0 psi for R-22; 3.0 psi 3.0\text{ psi} 3.0 psi for R-410A).

Vapor Velocity for Oil Return: Mineral oils and Polyolester (POE) lubricants travel entrained in refrigerant vapor. Horizontal suction lines require a minimum velocity of 500 to 750 FPM 500\text{ to }750\text{ FPM} 500 to 750 FPM . Vertical suction risers require a minimum velocity of 1 , 000 to 1 , 500 FPM 1,000\text{ to }1,500\text{ FPM} 1 , 000 to 1 , 500 FPM to carry oil upward against gravity.

Oil Traps: P-traps must be installed at the base of any vertical suction riser exceeding 8 feet 8\text{ feet} 8 feet , with additional traps installed every 15 to 20 feet 15\text{ to }20\text{ feet} 15 to 20 feet of continuous vertical rise.

Liquid Line Sizing Criteria:

Sized to maintain liquid velocity below 300 FPM 300\text{ FPM} 300 FPM to eliminate liquid hammer when solenoid valves close.

Total friction pressure drop plus static vertical elevation loss ( 0.50 psi/ft 0.50\text{ psi/ft} 0.50 psi/ft rise for R-410A liquid) must not exceed available subcooling, or flash gas will choke the metering device.

ASHRAE Standard 34 Safety Classifications & Modern Low-GWP Refrigerants

Refrigerants are classified by ASHRAE Standard 34 according to toxicity (Class A = Lower toxicity; Class B = Higher toxicity) and flammability (Class 1 = No flame propagation; Class 2L = Lower flammability; Class 2 = Flammable; Class 3 = Higher flammability): ASHRAE Standard 34 Safety Matrix

  • -----------------------------------------------------------
  • Increasing Flammability | Lower Toxicity | Higher Toxicity
  • -----------------------+--------------------+----------------------
  • Class 3 (High) | A3 (R-290 Propane) | B3
  • Class 2 (Flammable) | A2 (R-152a) | B2
  • Class 2L (Mild) | A2L (R-454B, R-32) | B2L (R-717 Ammonia)
  • Class 1 (No Flame) | A1 (R-410A, R-22) | B1 (R-123)
  • -----------------------------------------------------------
  • Low-GWP Transition & Zeotropic Temperature Glide

Under EPA AIM Act regulations, high-GWP refrigerants like R-410A (GWP = 2,088) are phased down in favor of A2L refrigerants like R-454B (GWP = 466) and R-32 (GWP = 675):

Zeotropic Blends (R-400 Series): Blends of multiple refrigerants with different boiling points exhibit Temperature Glide (the difference between Bubble Point liquid temperature and Dew Point vapor temperature during phase change). R-454B exhibits a glide of ≈ 1.5 ∘ F \approx 1.5^\circ\text{F} ≈ 1. 5 ∘ F .

Fractionation & Liquid Charging: Zeotropic blends must always be charged as a pure liquid from the cylinder to prevent fractionation (unequal boiling of blend components), using a manifold throttling valve to flash liquid to vapor before entering the suction service port.

  • Step-by-Step Worked Technical Examples
  • Example 1: Full Thermodynamic Cycle Analysis (3-Ton R-410A System)

Problem: A 3 -Ton 3\text{-Ton} 3 -Ton ( 36 , 000 BTU/hr 36,000\text{ BTU/hr} 36 , 000 BTU/hr ) R-410A air conditioning system operates with the following state point enthalpies extracted from a P P P - h h h chart:

  • Evaporator Outlet Enthalpy ( h 1 h_1 h 1 ​ ): 120.0 BTU/lb 120.0\text{ BTU/lb} 120.0 BTU/lb
  • Compressor Discharge Enthalpy ( h 2 h_2 h 2 ​ ): 138.0 BTU/lb 138.0\text{ BTU/lb} 138.0 BTU/lb
  • Condenser Outlet Liquid Enthalpy ( h 3 h_3 h 3 ​ ): 45.0 BTU/lb 45.0\text{ BTU/lb} 45.0 BTU/lb
  • Metering Device Outlet Enthalpy ( h 4 h_4 h 4 ​ ): 45.0 BTU/lb 45.0\text{ BTU/lb} 45.0 BTU/lb

Calculate: (1) Net Refrigerating Effect ( N R E NRE NRE ), (2) Mass Flow Rate ( m ˙ \dot{m} m ˙ ), (3) Work of Compression ( W c W_c W c ​ ), (4) Compressor Power in kW \text{kW} kW , (5) Total Heat of Rejection ( T H R THR T H R ), and (6) System C O P COP COP and E E R EER EER .

Solution:

Net Refrigerating Effect ( N R E NRE NRE ): N R E = h 1 − h 4 = 120.0 − 45.0 = 75.0 BTU/lb NRE = h_1 - h_4 = 120.0 - 45.0 = \mathbf{75.0\text{ BTU/lb}} NRE = h 1 ​ − h 4 ​ = 120.0 − 45.0 = 75.0 BTU/lb

Refrigerant Mass Flow Rate ( m ˙ \dot{m} m ˙ ): m ˙ = Capacity (BTU/hr) N R E = 36 , 000 BTU/hr 75.0 BTU/lb = 480.0 lbs/hr ( 8.0 lbs/min ) \dot{m} = \frac{\text{Capacity (BTU/hr)}}{NRE} = \frac{36,000\text{ BTU/hr}}{75.0\text{ BTU/lb}} = \mathbf{480.0\text{ lbs/hr}} \quad (8.0\text{ lbs/min}) m ˙ = NRE Capacity (BTU/hr) ​ = 75.0 BTU/lb 36 , 000 BTU/hr ​ = 480.0 lbs/hr ( 8.0 lbs/min )

Work of Compression ( W c W_c W c ​ ): W c = h 2 − h 1 = 138.0 − 120.0 = 18.0 BTU/lb W_c = h_2 - h_1 = 138.0 - 120.0 = \mathbf{18.0\text{ BTU/lb}} W c ​ = h 2 ​ − h 1 ​ = 138.0 − 120.0 = 18.0 BTU/lb

Compressor Theoretical Power Output: Power (BTU/hr) = m ˙ × W c = 480.0 lbs/hr × 18.0 BTU/lb = 8 , 640 BTU/hr \text{Power (BTU/hr)} = \dot{m} \times W_c = 480.0\text{ lbs/hr} \times 18.0\text{ BTU/lb} = 8,640\text{ BTU/hr} Power (BTU/hr) = m ˙ × W c ​ = 480.0 lbs/hr × 18.0 BTU/lb = 8 , 640 BTU/hr Power (kW) = 8 , 640 BTU/hr 3 , 412.14 BTU/kWh = 2.532 kW ( 2 , 532 Watts ) \text{Power (kW)} = \frac{8,640\text{ BTU/hr}}{3,412.14\text{ BTU/kWh}} = \mathbf{2.532\text{ kW}} \quad (2,532\text{ Watts}) Power (kW) = 3 , 412.14 BTU/kWh 8 , 640 BTU/hr ​ = 2.532 kW ( 2 , 532 Watts )

Total Heat of Rejection ( T H R THR T H R ): T H R specific = h 2 − h 3 = 138.0 − 45.0 = 93.0 BTU/lb THR_{\text{specific}} = h_2 - h_3 = 138.0 - 45.0 = \mathbf{93.0\text{ BTU/lb}} T H R specific ​ = h 2 ​ − h 3 ​ = 138.0 − 45.0 = 93.0 BTU/lb T H R rate = m ˙ × T H R specific = 480.0 × 93.0 = 44 , 640 BTU/hr THR_{\text{rate}} = \dot{m} \times THR_{\text{specific}} = 480.0 \times 93.0 = \mathbf{44,640\text{ BTU/hr}} T H R rate ​ = m ˙ × T H R specific ​ = 480.0 × 93.0 = 44 , 640 BTU/hr

Verification: T H R = Capacity + Work = 36 , 000 + 8 , 640 = 44 , 640 BTU/hr THR = \text{Capacity} + \text{Work} = 36,000 + 8,640 = 44,640\text{ BTU/hr} T H R = Capacity + Work = 36 , 000 + 8 , 640 = 44 , 640 BTU/hr .

C O P COP COP and E E R EER EER : COP = N R E W c = 75.0 BTU/lb 18.0 BTU/lb = 4.167 \text{COP} = \frac{NRE}{W_c} = \frac{75.0\text{ BTU/lb}}{18.0\text{ BTU/lb}} = \mathbf{4.167} COP = W c ​ NRE ​ = 18.0 BTU/lb 75.0 BTU/lb ​ = 4.167 EER = 3.41214 × COP = 3.41214 × 4.167 = 14.22 BTU/(W ⋅ hr) \text{EER} = 3.41214 \times \text{COP} = 3.41214 \times 4.167 = \mathbf{14.22\text{ BTU/(W}\cdot\text{hr)}} EER = 3.41214 × COP = 3.41214 × 4.167 = 14.22 BTU/(W ⋅ hr)

Example 2: Compression Ratio Calculation

Problem: A technician attaches digital gauges to an operating heat pump and records a suction pressure of 118.0 psig 118.0\text{ psig} 118.0 psig and a liquid head pressure of 380.0 psig 380.0\text{ psig} 380.0 psig . Calculate the operating compression ratio ( C R CR CR ).

Solution:

Convert gauge pressures to absolute: P suction, abs = 118.0 psig + 14.7 = 132.7 psia P_{\text{suction, abs}} = 118.0\text{ psig} + 14.7 = 132.7\text{ psia} P suction, abs ​ = 118.0 psig + 14.7 = 132.7 psia P discharge, abs = 380.0 psig + 14.7 = 394.7 psia P_{\text{discharge, abs}} = 380.0\text{ psig} + 14.7 = 394.7\text{ psia} P discharge, abs ​ = 380.0 psig + 14.7 = 394.7 psia

Calculate Compression Ratio: C R = P discharge, abs P suction, abs = 394.7 psia 132.7 psia = 2.97 : 1 CR = \frac{P_{\text{discharge, abs}}}{P_{\text{suction, abs}}} = \frac{394.7\text{ psia}}{132.7\text{ psia}} = \mathbf{2.97:1} CR = P suction, abs ​ P discharge, abs ​ ​ = 132.7 psia 394.7 psia ​ = 2.97 : 1

Example 3: Diagnostic Superheat & Subcooling Verification

Problem: An R-410A system with a TXV shows the following field service readings:

Suction Pressure = 118.0 psig 118.0\text{ psig} 118.0 psig (R-410A Saturation Temp = 40.0 ∘ F 40.0^\circ\text{F} 40. 0 ∘ F )

Suction Line Temperature at Compressor Inlet = 52.0 ∘ F 52.0^\circ\text{F} 52. 0 ∘ F

Liquid Line Pressure = 335.0 psig 335.0\text{ psig} 335.0 psig (R-410A Saturation Temp = 104.0 ∘ F 104.0^\circ\text{F} 104. 0 ∘ F )

Liquid Line Temperature at Condenser Outlet = 92.0 ∘ F 92.0^\circ\text{F} 92. 0 ∘ F

Determine whether superheat and subcooling are within normal operating ranges.

Solution:

Superheat Calculation: Superheat = T measured vapor − T sat = 52.0 ∘ F − 40.0 ∘ F = 12.0 ∘ F \text{Superheat} = T_{\text{measured vapor}} - T_{\text{sat}} = 52.0^\circ\text{F} - 40.0^\circ\text{F} = \mathbf{12.0^\circ\text{F}} Superheat = T measured vapor ​ − T sat ​ = 52. 0 ∘ F − 40. 0 ∘ F = 12. 0 ∘ F

(Normal TXV superheat target is typically 10 ∘ F 10^\circ\text{F} 1 0 ∘ F to 14 ∘ F 14^\circ\text{F} 1 4 ∘ F ; normal operation).

Subcooling Calculation: Subcooling = T sat − T measured liquid = 104.0 ∘ F − 92.0 ∘ F = 12.0 ∘ F \text{Subcooling} = T_{\text{sat}} - T_{\text{measured liquid}} = 104.0^\circ\text{F} - 92.0^\circ\text{F} = \mathbf{12.0^\circ\text{F}} Subcooling = T sat ​ − T measured liquid ​ = 104. 0 ∘ F − 92. 0 ∘ F = 12. 0 ∘ F

(Normal nameplate subcooling target is typically 10 ∘ F 10^\circ\text{F} 1 0 ∘ F to 14 ∘ F 14^\circ\text{F} 1 4 ∘ F ; proper charge confirmed).

Loading diagram... The Four-Component Vapor-Compression Refrigeration Cycle