Study guide
8.2 Spray Delivery Systems: Pumps, Agitators & Nozzles
North Carolina Pesticide Applicator Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Federal & North Carolina Pesticide Regulatory Framework
1.1 Federal Laws & Regulatory Agencies 1.2 North Carolina Pesticide Law of 1971 & NCDA&CS 1.3 North Carolina Applicator Licenses, Categories & Recertification 1.4 Compliance, Recordkeeping & Direct Supervision 1.5 The NCDA&CS Exams: Format, Fees, Scoring & Exam-Day Rules 1.6 Professionalism: Chemical Security, Risk Communication & Stewardship
2 Chapter 2: Pesticide Labeling & Legal Compliance
2.1 Label Components & Registration Numbers 2.2 Signal Words, Precautionary Statements & Toxicity Categories 2.3 Directions for Use, REI & Agricultural vs Non-Agricultural Statements 2.4 Safety Data Sheets (SDS) & Special Labeling Types
3 Chapter 3: Formulations, Adjuvants & Tank Mixing
3.1 Pesticide Types, Target Pest Groups & Modes of Action 3.2 Liquid Formulations: Chemistry, Performance & Handling 3.3 Dry & Specialty Formulations: Physical Characteristics & Safety 3.4 Adjuvants & Additives: Function, Chemistry & Selection 3.5 Tank Mixing Procedures, Compatibility & Jar Testing
4 Chapter 4: Human Toxicology & Exposure Hazards
4.1 Hazard, Toxicity & Exposure Principles 4.2 Routes of Exposure & Symptom Recognition 4.3 Cholinesterase Inhibition & Specific Chemical Hazards 4.4 First Aid & Emergency Medical Response
5 Chapter 5: Personal Protective Equipment (PPE) & Handler Safety
5.1 Work Clothing & Chemical-Resistant PPE Selection 5.2 Respiratory Protection & Fit Testing 5.3 PPE Maintenance, Cleaning & Decontamination 5.4 Heat Stress Prevention & Management
6 Chapter 6: Environmental Fate & Water Protection
6.1 Pesticide Movement & Environmental Fate 6.2 Groundwater & Surface Water Protection 6.3 Soil Characteristics & Leaching Vulnerability
7 Chapter 7: Protecting Non-Target Organisms & Drift Management
7.1 Spray Drift Management & Meteorological Factors 7.2 Pollinator Protection & Honey Bee Safety 7.3 Wildlife & Endangered Species Protection
8 Chapter 8: Application Equipment & Component Mechanics
8.1 Sprayer Types & Specialized Equipment 8.2 Spray Delivery Systems: Pumps, Agitators & Nozzles 8.3 Equipment Maintenance, Cleaning & Storage
9 Chapter 9: Equipment Calibration & Mathematical Calculations
9.1 Liquid Sprayer Calibration Math 9.2 Tank Mixing & Area Application Math 9.3 Granular Applicator Calibration & Area Math
10 Chapter 10: Safe Handling, Storage, Transportation & Disposal
10.1 Mixing, Loading & Spill Response 10.2 Storage Facility Safety & Security 10.3 Container Rinsing & Disposal Programs 10.4 Transportation & DOT Requirements
11 Chapter 11: Worker Protection Standard (WPS) & Integrated Pest Management (IPM)
11.1 Worker Protection Standard (WPS) Compliance 11.2 Restricted-Entry Intervals (REI) & Early-Entry Exceptions 11.3 IPM Principles & Strategies 11.4 Pest Identification & Action Thresholds
8.2 Spray Delivery Systems: Pumps, Agitators & Nozzles
Key Takeaways Explain This Topic AI
Spray pumps must be selected based on required operating pressure, flow capacity, and formulation compatibility: Centrifugal pumps handle abrasive wettable powders well at high volume (50–100+ GPM) and low pressure (30–70 psi), whereas Diaphragm and Piston pumps deliver high pressures (200–1,000 psi) with positive displacement.
Roller pumps are economical and popular for non-abrasive emulsions and solutions at 100–300 psi, but experience severe, rapid internal scoring and seal failure when pumping abrasive wettable powders (WP) or dry flowables (WDG/DF).
Continuous tank agitation is critical: Hydraulic jet agitation requires 20% to 30% of total pump capacity (or specialized venturi aspirators) for wettable powder suspensions, while mechanical paddle agitation provides positive physical mixing for heavy slurries.
Sprayer filtration follows a strict cascade: 20–30 mesh at the tank basket opening, 40–50 mesh on the pump suction intake line, and 50–100 mesh at individual nozzle bodies to prevent orifice clogging without starving the pump.
Nozzle pattern and metallurgy dictate field performance: Even flat-fan nozzles (E-series) are engineered exclusively for banding over crop rows, standard flat-fans require 30–50% overlap for broadcast spraying, and Ceramic orifices provide 20–50 times the wear resistance of soft Brass.
Last updated: August 2026
8.2 Spray Delivery Systems: Pumps, Agitators & Nozzles
Quick Answer: A liquid sprayer's delivery circuit consists of five interlocking mechanical systems: the tank , pump , agitation system , filtration cascade , and nozzles . Centrifugal pumps handle abrasive wettable powders at high volume (50–100+ GPM) and low pressure (30–70 psi); roller pumps provide economical 100–300 psi output but wear rapidly from abrasive powders; diaphragm pumps (200–700 psi) and piston pumps (up to 1,000 psi) handle high pressures with positive displacement. Filtration cascades from 20–30 mesh at the tank basket to 40–50 mesh at the pump suction line and 50–100 mesh at nozzle bodies. Standard flat-fan nozzles require 30–50% overlap for uniform broadcast, even flat-fans (E-series) are strictly for banding, and ceramic orifices outlast brass by 20 to 50 times.
1. Sprayer Plumbing Architecture & Tank Materials
The sprayer plumbing circuit routes chemical solution from the supply tank through filtration, pressurization, regulation, agitation, and atomization components. +-----------------------------------------------------------------------------+
- | SPRAY CIRCUIT PLUMBING FLOW |
- | |
- | +---------------------------------------------------------------------+ |
- | | SPRAY TANK | |
- | | - Basket Strainer (20-30 mesh) at fill neck | |
- | | - Bottom sump with drain plug & anti-vortex baffles | |
- | +-------------------+-----------------------------+-------------------+ |
- | | ^ |
- | v (Suction Line) | (Agitation / Bypass) |
- | [SUCTION STRAINER (40-50 Mesh)] | |
- | | | |
- | v | |
- | [PUMP UNIT] | |
- | (Centrifugal/Roller/Diaphragm) | |
- | | | |
- | v (Pressure Line) | |
- | [PRESSURE REGULATOR / UNLOADER] ---------+ |
- | | |
- | +---> [LIQUID-FILLED PRESSURE GAUGE] |
- | | |
- | v (Discharge Line) |
- | [IN-LINE STRAINER (50-80 Mesh)] |
- | | |
- | v |
- | [SPRAY BOOM / WAND] |
- | | |
- | v |
- | [NOZZLE STRAINER (50-100 Mesh) + BALL CHECK VALVE] |
- | | |
- | v |
- | [SPRAY NOZZLE ORIFICE] |
- +-----------------------------------------------------------------------------+
- Spray Tank Engineering & Materials
Polyethylene (High-Density Poly / HDPE): Most common agricultural tank material. Highly resistant to corrosive chemicals and fertilizers, lightweight, inexpensive, and translucent (molded gallon markers allow rapid visual fluid verification). Disadvantages: Susceptible to ultraviolet (UV) degradation over time; cannot be structurally welded or patched if cracked.
Fiberglass: Extremely durable, highly chemical-resistant, and repairable using resin and fiberglass matting. Disadvantages: Opaque (requires external clear sight tube); more expensive and heavier than poly.
Stainless Steel: Maximum durability and corrosion resistance across virtually all agricultural chemicals and solvents. Withstands high operating pressures. Disadvantages: Heavy and expensive.
Aluminum: Lightweight and corrosion-resistant for specific organic herbicides. Critical Limitation: Severely corroded by liquid nitrogen fertilizer solutions and acidic pesticide tank mixes.
2. Spray Pumps: Mechanics, Pressure & Formulation Compatibility
Pumps fall into two fundamental engineering classes: positive displacement and non-positive displacement . +-----------------------------------------------------------------------------+
- | PUMP CLASSIFICATION DYNAMICS |
- | |
- | [POSITIVE DISPLACEMENT] [NON-POSITIVE DISPLACEMENT] |
- | - Roller, Diaphragm, Piston - Centrifugal |
- | - Flow rate is constant per revolution; - Flow varies inversely with |
- | discharge is forced regardless of psi discharge pressure |
- | - MANDATORY: Pressure relief/unloader - Cannot blow lines when shut |
- | valve to prevent line bursting off (liquid simply recirculates)|
- | - Self-priming; handles high pressures - Not self-priming; high volume |
+-----------------------------------------------------------------------------+ +-----------------------------------------------------------------------------+
- | PUMP TYPE COMPARISON MATRIX |
- | |
- | Pump Type Operating PSI Flow Rate (GPM) Abrasive WP? Self-Prime? |
- | ───────────────────────────────────────────────────────────────────────── |
- | Centrifugal 30–70 psi 50–140+ GPM EXCELLENT No |
- | Roller 100–300 psi 8–30 GPM POOR (Wears) Yes |
- | Diaphragm 200–700 psi 10–60 GPM EXCELLENT Yes |
- | Piston 200–1,000+ psi 10–60 GPM GOOD Yes |
- +-----------------------------------------------------------------------------+
- 1. Centrifugal Pumps
Mechanics: High-speed rotating impeller (3,000 to 4,500 RPM, driven via tractor PTO step-up gearbox or hydraulic motor) throws liquid outward by centrifugal force, generating fluid velocity converted into pressure.
Performance: Produces high volume ( 50 to 140+ GPM ) at low-to-medium pressures ( 30 to 70 psi ).
Formulation Compatibility: Outstanding resistance to abrasive wettable powders, dry flowables, and liquid fertilizers because there are no rubbing metal-to-metal contact surfaces.
Priming: Non-positive displacement; not self-priming . Must be mounted below the bottom of the spray tank or equipped with a foot valve/priming line.
2. Roller Pumps
Mechanics: A slotted rotor rotates inside an eccentric housing. Rollers (nylon, Teflon, or rubber) slide in and out of the slots, sealing liquid and forcing it through the discharge port at 100 to 300 psi.
Performance: Self-priming, low-cost, compact, operating directly at 540 or 1,000 RPM PTO speeds.
Formulation Vulnerability: Highly susceptible to abrasive formulations (wettable powders, dry flowables, sulfur). Abrasive mineral particles become trapped between the rollers and casing, scoring the metal housing and causing rapid loss of pressure capacity within 20 to 50 operating hours. Ideal only for clear solutions and emulsifiable concentrates (EC).
3. Diaphragm Pumps
Mechanics: Synthetic rubber/elastomer diaphragms pulse back and forth inside sealed pumping cavities, driven by an oil-lubricated crankshaft and piston mechanism.
Performance: Positive displacement, self-priming, delivering 200 to 700 psi at 10 to 60 GPM .
Chemical Resistance: The elastomer diaphragm creates a complete physical barrier isolating the mechanical drive components from the chemical spray mixture. Handles abrasive suspensions, acidic chemicals, and liquid fertilizers with exceptional durability.
4. Piston Pumps
Mechanics: Reciprocating pistons fitted with leather, impregnated elastomer, or ceramic packings cycle within stainless steel or ceramic cylinder sleeves.
Performance: Positive displacement, self-priming, delivering high pressures (up to 1,000+ psi ) and constant output regardless of pressure.
Application: Standard pump for high-pressure tree fruit sprayers, orchard air-blast systems, and utility wash rigs. Requires a pulsation dampener (air chamber) on the discharge manifold to smooth out hydraulic pressure pulses.
3. Agitation Systems: Hydraulic vs. Mechanical
Continuous agitation is mandatory to maintain uniform chemical dispersion throughout the entire application. Without agitation, suspensions (WP, WDG, F) settle to the tank bottom, resulting in extreme chemical under-dosing early in the tank load and severe phytotoxic over-dosing at the bottom of the tank. +-----------------------------------------------------------------------------+
- | AGITATION DYNAMICS & DEMANDS |
- | |
- | [HYDRAULIC AGITATION] [MECHANICAL AGITATION] |
- | - Diverts pump bypass stream into tank - Steel shaft with rotating |
- | - Solutions/Emulsions: 5–10% pump flow paddles driven by PTO/engine |
- | - Wettable Powders: 20–30% pump flow - True physical churning for |
- | - Venturi Jet Agitators: Aspirator - Mandatory for heavy wettable |
- | nozzle multiplies fluid flow 3x to 5x powders in 500+ gal tanks |
- +-----------------------------------------------------------------------------+
- Hydraulic Agitation Sizing Rules
For true solutions (S/SL) and emulsions (EC): Requires 5% to 10% of total pump capacity .
For wettable powders (WP) and suspension flowables (F/SC): Requires 20% to 30% of total pump capacity (e.g., 6 to 10 GPM bypass for a 300-gallon tank).
Venturi Jet Agitators: Specialized nozzles installed at the tank bottom that utilize the Bernoulli principle. As pressurized bypass liquid flows through a small internal jet orifice, it creates a low-pressure zone that draws in 3 to 5 gallons of surrounding tank liquid for every 1 gallon pumped, dramatically boosting mixing efficiency.
4. Sprayer Filtration Cascade & Mesh Ratings
Filtration protects precision pumps, valves, and nozzle tips from abrasive wear and debris blockages.
Important
Understanding Mesh Sizing: Mesh rating indicates the number of square openings per linear inch of screen material. Higher mesh numbers indicate smaller openings and finer filtration. For example, a 100-mesh screen has much smaller openings than a 50-mesh screen. +-----------------------------------------------------------------------------+
- | FILTRATION CASCADE SYSTEM |
- | |
- | [1. TANK BASKET STRAINER] ---> 20 to 30 Mesh |
- | (Stops leaves, twigs, packaging fragments at fill neck) |
- | |
- | [2. PUMP SUCTION STRAINER] ---> 40 to 50 Mesh |
- | (Between tank and pump intake; protects pump from gravel/particulates)|
- | * CRITICAL: Never use >50 mesh on suction side (causes cavitation!) |
- | |
- | [3. IN-LINE BOOM STRAINER] ---> 50 to 80 Mesh |
- | (Between pressure regulator and boom; catches fine particles) |
- | |
- | [4. NOZZLE TIP STRAINERS] ---> 50 to 100 Mesh |
- | (Positioned behind each tip; protects precision orifice) |
- | * 100-mesh for fine tips (<0.15 GPM); 50-mesh for larger orifices |
- +-----------------------------------------------------------------------------+
- Suction Strainer Cavitation Hazard
Never install a fine mesh screen (such as 80 or 100 mesh) on the suction line leading into a centrifugal or roller pump. Fine screens restrict fluid intake, creating extreme vacuum on the inlet side that leads to pump cavitation —the violent formation and collapse of vapor bubbles that pit impellers and destroy mechanical pump seals.
5. Pressure Regulators, Unloaders & Liquid-Filled Gauges
Pressure Regulators / Relief Valves: Maintain uniform operating pressure at the spray boom by routing excess pump volume back into the tank via the bypass/agitation line.
Unloader Valves: Used on positive displacement piston and diaphragm pumps. When the spray boom shut-off valve is closed, the unloader valve completely unloads pump pressure, circulating fluid at near-zero psi to prevent pump overheating and engine stalling.
Pressure Gauges: Precision Bourdon tube instruments. Certified sprayers must utilize glycerin-filled or silicone-damped gauges . The internal viscous liquid cushions the internal gear mechanism against engine vibration and pump pressure pulsations, preventing needle flutter and premature gauge failure. Gauges should be sized so normal operating pressure falls within the middle 50% (one-third to two-thirds) of the gauge dial .
6. Nozzle Anatomy & Spray Pattern Classification
The spray nozzle is the single most critical component in the delivery chain. It meters flow rate (GPM), atomizes liquid into droplets, and forms the geometric spray pattern across the target. +-----------------------------------------------------------------------------+
- | NOZZLE SPRAY GEOMETRIES |
- | |
- | [STANDARD FLAT-FAN] [EVEN FLAT-FAN (E)] [HOLLOW CONE] |
- | - Pattern: Tapered fan - Pattern: Uniform band - Pattern: Circular ring|
- | - Overlap: 30% to 50% - Overlap: ZERO (Banding)- Overlap: None (Canopy)|
- | - Use: Broadcast boom - Use: Band over crop row- Use: Contact foliar |
- +-----------------------------------------------------------------------------+
- 1. Standard Flat-Fan Nozzles
Geometry: Produces an oval-shaped, tapered-edge flat fan pattern with spray angles of 80° or 110° .
Operating Dynamics: Operating pressure is typically 30 to 50 psi . Because the spray pattern deposits less liquid at the outer margins, adjacent nozzles on a boom must have their patterns overlapped by 30% to 50% to achieve a completely uniform spray distribution across the field.
Extended Range (XR) Flat-Fans: Engineered to maintain a uniform fan pattern across a wide pressure range ( 15 to 60 psi ), allowing applicators to reduce pressure to 15–20 psi in breezy conditions to produce larger, drift-resistant droplets.
Air-Induction (AI) / Venturi Flat-Fans: Incorporates an internal venturi jet that draws atmospheric air into the liquid stream, producing large, air-filled droplets that minimize drift and splatter upon leaf impact for excellent coverage.
2. Even Flat-Fan Nozzles (E-Series, e.g., 8002E)
Geometry: Produces a crisp, rectangular fan pattern with completely uniform liquid distribution across the entire swath width (no tapered edges).
Application Rule: Designed strictly for band applications (e.g., applying pre-emergence herbicides in a 10-inch band directly over a seeded crop row or between crop beds).
Critical Exam Rule: NEVER use Even Flat-Fan nozzles on a broadcast boom! Overlapping even flat-fan nozzles creates severe double-rate banding stripes and crop injury across the entire field.
3. Cone Nozzles (Hollow Cone & Full/Solid Cone)
Geometry: Liquid enters a whirl chamber (disc-core assembly) that imparts high rotational velocity, discharging spray in a circular ring ( hollow cone ) or uniform solid circle ( full cone ).
Dynamics: Operates at 40 to 100+ psi , producing fine-to-medium droplets with multi-directional velocity.
Best Use: Superior canopy penetration and under-leaf coverage for contact fungicides, contact insecticides, and defoliants . Unsuitable for broadcast systemic herbicides due to high drift risk.
4. Flood / Deflector Nozzles
Geometry: Discharges a low-pressure liquid stream against a smooth deflector plate, creating a wide-angle ( 120° to 140° ) fan pattern.
Dynamics: Operates at low pressure ( 10 to 25 psi ) producing large, coarse droplets resistant to drift.
Best Use: Broadcast pre-emergence herbicides, liquid fertilizer suspension applications, and drift-sensitive turf treatments.
7. Nozzle Orifice Materials & Wear Metallurgy
Abrasive formulation slurries (wettable powders, dry flowables) and high operating pressures cause abrasive erosion of the precision-machined nozzle orifice. As the orifice wears, its cross-sectional area expands, resulting in higher output (GPM), distorted spray patterns, and over-application . +-----------------------------------------------------------------------------+
- | NOZZLE MATERIAL WEAR RESISTANCE HIERARCHY |
- | |
- | Brass [====] 1.0x (Baseline - Fastest Wear) |
- | Aluminum [======] 1.5x to 2.0x |
- | Polymer/Nylon [=========] 2.0x to 3.0x |
- | St. Steel [==================] 4.0x to 6.0x |
- | Hardened SS [====================================] 10.0x to 15.0x |
- | Ceramic [==================================================] 20–50x |
- +-----------------------------------------------------------------------------+
Brass: Soft alloy; lowest initial cost; fastest wear rate (baseline = 1.0x). Abrasive wettable powders erode brass orifices within 15–30 operating hours. Orifices are easily gouged and ruined by cleaning with metal objects.
Aluminum: Inexpensive; moderate wear resistance (1.5–2.0x brass); easily corroded by fertilizers.
Polymer / Nylon: Good wear resistance (2.0–3.0x brass); highly resistant to chemical corrosion and fertilizers. Inexpensive; can swell if exposed to certain aromatic solvents.
Stainless Steel: High wear resistance (4.0–6.0x brass); excellent resistance to abrasive suspensions and corrosive chemicals. Industry standard for commercial agriculture.
Hardened Stainless Steel: Extreme durability (10.0–15.0x brass); excellent for extensive high-pressure spraying of abrasive wettable powders.
Ceramic (Alumina): Ultimate wear resistance ( 20.0 to 50.0x brass ); virtually impervious to abrasive erosion from flowables and wettable powders. Limitation: Brittle; can crack if dropped or overtightened with metal wrenches.
8. Summary Comparison of Nozzle Geometries & Materials
Nozzle Pattern Type Spray Angle Operating Pressure Droplet Spectrum Swath Overlap Requirement Primary Agricultural / Commercial Use
Standard Flat-Fan 80° or 110° 30–50 psi Medium to Coarse 30% to 50% Overlap Broadcast herbicides, insecticides on boom sprayers
Extended Range (XR) 80° or 110° 15–60 psi Coarse (low psi) to Fine 30% to 50% Overlap Wide-pressure broadcast spraying with drift control
Air-Induction (AI) 110° 30–70 psi Ultra-Coarse (Air-filled) 30% to 50% Overlap High-drift-risk broadcast systemic herbicide applications
Even Flat-Fan (E) 80° or 95° 20–40 psi Medium to Coarse 0% (No Overlap - Banding) Band applications over crop rows or between beds
Hollow Cone 60° to 90° 40–100+ psi Fine to Medium None (Canopy Penetration) Contact fungicides, foliar insecticides, defoliation
Flood / Deflector 120° to 140° 10–25 psi Very Coarse 30% to 50% Overlap Liquid fertilizers, soil herbicides, drift reduction