Study guide
10.1 NC Residential Code Scope, Administration, Materials & Water Supply for Dwellings
North Carolina Plumbing Contractor Exam Class I & Class II
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview, Administration & General Code Regulations
1.1 NC Plumbing Licensing, Board Rules & Exam Structure 1.2 General Regulations, Piping Support, Trenching & Protection 1.3 Plumbing Mathematics, Grade Calculations & Isometric Plan Reading 1.4 Permits, Plan Review, Required Inspections & Code-Mandated Tests 1.5 Approved Materials, Standards, Joints & Connections
2 Chapter 2: Fixtures, Faucets, Fixture Fittings & Water Heaters
2.1 Minimum Fixture Requirements, Accessibility (ADA) & Rough-In Spacing 2.2 Fixture Installation, Setting Clearances & Flushometer Valves 2.3 Water Heater Sizing, Temperature & Pressure Relief (T&P) Valves & Safety Devices
3 Chapter 3: Water Supply and Distribution & Backflow Prevention
3.1 Water Service Sizing, Materials & Pressure Regulation 3.2 Water Supply Fixture Units (WSFU) & Pipe Sizing Methods 3.3 Cross-Connection Control, Backflow Prevention Devices & Hazards 3.4 Hot and Cold Water Distribution Design & Pressure Loss Calculations
4 Chapter 4: Sanitary Drainage, Indirect Waste, Sumps & Ejectors
4.1 Drainage System Principles, Flow Velocities & Minimum Slope Requirements 4.2 Drainage Fixture Unit (DFU) Sizing for Building Drains, Sewers & Stacks 4.3 Cleanout Sizing, Locations, Clearances & Installation Standards 4.4 Sewage Sumps, Macerating Systems & Indirect/Special Waste 4.5 Building Sewers, Sewer Connections & Private Sewage Disposal
5 Chapter 5: Vents and Venting Systems
5.1 Venting Principles, Termination & Minimum Sizing 5.2 Wet Venting, Common Venting & Stack Vent Systems 5.3 Circuit & Loop Venting, Combination Waste & Vent Systems 5.4 Island Fixture Venting & Air Admittance Valves (AAVs)
6 Chapter 6: Traps, Interceptors, Separators & Storm Drainage
6.1 Trap Design, Prohibited Traps & Trap Arm Developed Lengths 6.2 Grease Interceptors, Oil Separators & Sand Traps 6.3 Storm Drainage Sizing, Roof Drains & Secondary (Emergency) Overflow Systems
7 Chapter 7: Fuel Gas Piping & Appliance Venting (NC IFGC)
7.1 Fuel Gas Fundamentals, Materials, Jointing & Mandatory Pressure Testing 7.2 Fuel Gas Pipe Sizing: Longest Length & Branch Sizing Methods 7.3 Combustion Air Requirements: Indoor, Outdoor & Engineered Openings 7.4 Fuel Gas Appliance Venting: Category I–IV Systems, Chimneys & Clearances
8 Chapter 8: Safety, Excavation & Jobsite Practices (OSHA 1926)
8.1 OSHA Standards for Plumbing: PPE, Fall Protection & Hazard Communication 8.2 Trenching, Shoring, Soil Classifications & Confined Space Safety 8.3 Soldering, Brazing, Hot Work Permits & Jobsite Fire Prevention
9 Chapter 9: NC Contractor Business Law, Project Management & Liens (NASCLA / 21 NCAC 50)
9.1 NC Board Laws (NCGS 87-2), Administrative Rules (21 NCAC 50) & Disciplinary Actions 9.2 Estimating, Job Costing, Bidding & Contract Administration 9.3 North Carolina Mechanics' Lien Laws, Payment Bonds & Dispute Resolution 9.4 Financial Management, Tax Compliance, Workers' Compensation & Business Insurance 9.5 Business Formation, Entity Licensing & Startup Compliance in North Carolina 9.6 Employment Law, Payroll Compliance & Workforce Management 9.7 Project Management: Scheduling, Submittals, Documentation & Closeout 9.8 Surety Bonding, Risk Transfer & Claims Management 9.9 Environmental, Erosion Control & Jobsite Regulatory Compliance
10 Chapter 10: NC Residential Code Plumbing (Class II & Dwelling Practice)
10.1 NC Residential Code Scope, Administration, Materials & Water Supply for Dwellings 10.2 NC Residential Code DWV, Venting, Traps & Fuel Gas Provisions for Dwellings
10.1 NC Residential Code Scope, Administration, Materials & Water Supply for Dwellings
Key Takeaways Explain This Topic AI
The NC Residential Code is a required reference book for the Plumbing Class I, Class II, Restricted Limited and Plumbing Technician examinations, and it is the only technical code book on the Class II list besides the Administration Code.
The Residential Code applies to detached one- and two-family dwellings and townhouses not more than three stories above grade with a separate means of egress; anything else falls under the NC Plumbing Code.
Residential water distribution may be sized by the prescriptive tables in the Residential Code rather than by a full WSFU and friction-loss analysis, which is why a Class II candidate must know both routes.
Residential water service is a minimum of 3/4 inch, the water distribution pipe from the service to the water heater and to the fixture group is sized from the prescriptive table, and the same 80 psi trigger for a pressure reducing valve applies.
The Residential Code carries its own test requirements, including a water supply test at working pressure and a DWV test by 10-foot head of water or 5 psi of air.
Last updated: September 2026
10.1 NC Residential Code Scope, Administration, Materials & Water Supply for Dwellings
Quick Answer: The NC State Building Code: Residential Code (NCRC), 2018 edition , is reference book "F" on the Board's list and is required for the Class I, Class II, Restricted Limited Plumbing, and Plumbing Technician examinations. It governs detached one- and two-family dwellings and townhouses not more than three stories above grade plane with a separate means of egress . Everything else is NC Plumbing Code territory. The plumbing provisions live in Part VII (Chapters 25 through 33) , with fuel gas in Chapter 24 . Residential water distribution may be sized by prescriptive table instead of a full WSFU and friction-loss analysis. The minimum water service is 3/4 inch , a pressure reducing valve is required where static pressure exceeds 80 psi , and DWV is tested by 10-foot head of water or 5 psi air .
Why This Code Book Matters on the Exam
Candidates routinely arrive with the Plumbing Code tabbed and the Residential Code untouched. That is a mistake in two directions:
Class II is a residential licence. A Class II Plumbing Contractor is restricted to single-family detached residential dwellings, and the Board's Book Reference List for Class II includes the Administration Code, the Residential Code, the Laws & Rules book, and the business book — but not the Plumbing Code or the Fuel Gas Code. For a Class II candidate, the Residential Code is the technical code.
Class I candidates get residential questions too. The Class I list includes the Residential Code alongside the Plumbing and Fuel Gas Codes, so a Class I exam can legitimately ask a question answerable only from the residential book — and the two books do not always give the same answer.
Exam Strategy: When a question describes a single-family dwelling, a duplex, or a three-story townhouse with its own egress , reach for the Residential Code first . When it describes an apartment building, a commercial occupancy, an institutional building, or anything four stories or taller, reach for the Plumbing Code .
Scope, Applicability & the Boundary with the Plumbing Code
Applies to: detached one- and two-family dwellings, and townhouses not more than three stories above grade plane , each unit having a separate means of egress , together with their accessory structures.
Does not apply to: apartment buildings and other multi-family occupancies, mixed-use buildings, commercial, institutional, and industrial occupancies, and townhouses exceeding three stories or lacking separate egress. These use the NC Plumbing Code and the NC Mechanical and Fuel Gas codes.
Live/work and accessory dwellings may fall under the residential code within the limits the code sets — read the scope section rather than assuming.
Existing buildings. Repairs and alterations to existing dwellings are governed by the North Carolina existing-building provisions; a like-for-like repair is generally allowed to match the original method, but an alteration must meet current requirements for the work performed.
Administration. Permits, inspections, and certificates for residential work run through the same local code enforcement office and the same Administration Code and Policies used for commercial work — and through the same 21 NCAC 50 .0402 licensee obligations covered in Section 1.4, including the water heater replacement exemption for one- and two-family dwellings .
Residential Plumbing Materials
The residential material lists parallel the Plumbing Code lists but are organised by system rather than by table number, and a few residential-only allowances exist.
System Commonly approved in dwellings Watch for
Water service Copper Type K and L, PEX, PE-RT, CPVC, PVC (cold only), PE/HDPE, ductile iron, brass The North Carolina restriction to Type K, WK, L, WL below grade applies here too — no Type M underground.
Water distribution Copper Type K, L, M; PEX; PE-RT; CPVC; PEX-AL-PEX; galvanized steel (legacy); brass PVC and PE are not water distribution materials.
DWV aboveground PVC schedule 40, ABS, cast iron, copper DWV, galvanized (legacy) ABS and PVC may not be solvent cemented together.
DWV underground / building sewer PVC, ABS, cast iron, vitrified clay (sewer), PE Bedding and cover requirements from Section 4.5 apply unchanged.
Fittings Must match the pipe material and the service No bushings, saddles, or fittings with a ledge or shoulder in a drainage waterway.
Marking and listing requirements are identical to those in Section 1.5: pipe and fittings must bear a permanent mark showing the manufacturer and the referenced standard, potable-water components must meet NSF 61 and NSF 372 lead limits, and solder and flux for potable lines must be lead free .
Water Service & System Pressure
Minimum water service size: 3/4 inch. As in the Plumbing Code, this is a floor, not a design answer — a long run to a house with several bathrooms will need more.
Separation from the building sewer: the 5-foot rule and the solid-shelf, 12-inch-above-the-crown exception apply exactly as covered in Section 3.1.
Burial: below the frost line and not less than 12 inches below grade, with the North Carolina frost depths noted in Section 1.3.
Maximum pressure: where the static pressure at the building supply exceeds 80 psi , an approved pressure reducing valve is required, set to deliver a working pressure that does not exceed 80 psi. A PRV with an internal check creates a closed system , which requires thermal expansion control exactly as covered in Section 2.3.
Minimum pressure and flow: the residential code sets minimum flow rates and pressures at fixture outlets, and undersized or over-long distribution is the usual cause of a house that fails them.
Prescriptive Water Distribution Sizing
The Residential Code's most useful feature for a Class II contractor is that it allows prescriptive sizing tables as an alternative to a full engineered analysis.
How the prescriptive method works:
Determine the water service size and the water distribution (main) size from the table, using the number of fixtures served , the developed length , and the available static pressure range .
Size the branches to individual fixtures from the minimum fixture supply table: for example 1/2 inch to a lavatory, sink, water closet, tub, or shower; 3/4 inch to a hose bibb or a water heater; 1/2 inch to a dishwasher or clothes washer connection.
Verify the result against the maximum developed length the table permits for that pressure range.
When the prescriptive route fails, the designer falls back to the engineered method from Section 3.2: total WSFU , conversion to gpm, subtraction of static lift (0.433 psi per foot of elevation), meter and device losses , and the friction loss per 100 feet available to the longest run.
Worked Comparison: A two-story house with three bathrooms, a kitchen, a laundry, and two hose bibbs on a 60 psi service, 90 feet of developed length. The prescriptive table will typically return a 1-inch service and 3/4-inch distribution main with 1/2-inch branches. The engineered method on the same house lands in the same place — but if the developed length grows to 200 feet, or the static pressure drops to 40 psi, the prescriptive table runs out and the engineered method becomes the only defensible route.
Water Heaters in Dwellings
The residential provisions restate the safety requirements from Section 2.3 and add a few dwelling-specific ones:
Relief valve: every storage water heater requires a combination temperature and pressure relief valve rated to open at not more than 150 psi and 210 degrees F , with the temperature element in the top 6 inches of the tank.
Discharge piping: full size, downward by gravity, no valves or tees, no threaded terminal end, terminating through an air gap in an approved location where the discharge is visible.
Pan and drain: required where leakage would damage the structure — attic, upper floor, or over finished space — with a minimum 3/4-inch indirect drain.
Garage installation: the 18-inch ignition-source elevation rule and vehicle-impact protection apply, with the FVIR exception.
Seismic and support: heaters must be supported and secured against displacement.
Temperature control: the water heater thermostat is not a substitute for the ASSE 1016 shower valve or the ASSE 1070 device where those are required.
Residential Test Requirements
System Test
DWV rough 10-foot head of water , or 5 psi air held for 15 minutes without added air.
Water supply Tested at the working pressure of the system , proved tight, before concealment.
Building sewer 10-foot head of water held 15 minutes.
Fuel gas Air, CO₂, or nitrogen at the pressure and duration in NCRC Chapter 24 — never oxygen or a flammable gas.
Final Fixtures operational, traps sealed, relief discharge piped, cleanouts accessible.
Exam Trap: The residential and commercial test values are the same numbers. Where the codes do diverge is in DWV sizing, venting allowances, and cleanout requirements — which is the subject of Section 10.2.