Study guide
1.5 Approved Materials, Standards, Joints & Connections
North Carolina Plumbing Contractor Exam Class I & Class II
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview, Administration & General Code Regulations
1.1 NC Plumbing Licensing, Board Rules & Exam Structure 1.2 General Regulations, Piping Support, Trenching & Protection 1.3 Plumbing Mathematics, Grade Calculations & Isometric Plan Reading 1.4 Permits, Plan Review, Required Inspections & Code-Mandated Tests 1.5 Approved Materials, Standards, Joints & Connections
2 Chapter 2: Fixtures, Faucets, Fixture Fittings & Water Heaters
2.1 Minimum Fixture Requirements, Accessibility (ADA) & Rough-In Spacing 2.2 Fixture Installation, Setting Clearances & Flushometer Valves 2.3 Water Heater Sizing, Temperature & Pressure Relief (T&P) Valves & Safety Devices
3 Chapter 3: Water Supply and Distribution & Backflow Prevention
3.1 Water Service Sizing, Materials & Pressure Regulation 3.2 Water Supply Fixture Units (WSFU) & Pipe Sizing Methods 3.3 Cross-Connection Control, Backflow Prevention Devices & Hazards 3.4 Hot and Cold Water Distribution Design & Pressure Loss Calculations
4 Chapter 4: Sanitary Drainage, Indirect Waste, Sumps & Ejectors
4.1 Drainage System Principles, Flow Velocities & Minimum Slope Requirements 4.2 Drainage Fixture Unit (DFU) Sizing for Building Drains, Sewers & Stacks 4.3 Cleanout Sizing, Locations, Clearances & Installation Standards 4.4 Sewage Sumps, Macerating Systems & Indirect/Special Waste 4.5 Building Sewers, Sewer Connections & Private Sewage Disposal
5 Chapter 5: Vents and Venting Systems
5.1 Venting Principles, Termination & Minimum Sizing 5.2 Wet Venting, Common Venting & Stack Vent Systems 5.3 Circuit & Loop Venting, Combination Waste & Vent Systems 5.4 Island Fixture Venting & Air Admittance Valves (AAVs)
6 Chapter 6: Traps, Interceptors, Separators & Storm Drainage
6.1 Trap Design, Prohibited Traps & Trap Arm Developed Lengths 6.2 Grease Interceptors, Oil Separators & Sand Traps 6.3 Storm Drainage Sizing, Roof Drains & Secondary (Emergency) Overflow Systems
7 Chapter 7: Fuel Gas Piping & Appliance Venting (NC IFGC)
7.1 Fuel Gas Fundamentals, Materials, Jointing & Mandatory Pressure Testing 7.2 Fuel Gas Pipe Sizing: Longest Length & Branch Sizing Methods 7.3 Combustion Air Requirements: Indoor, Outdoor & Engineered Openings 7.4 Fuel Gas Appliance Venting: Category I–IV Systems, Chimneys & Clearances
8 Chapter 8: Safety, Excavation & Jobsite Practices (OSHA 1926)
8.1 OSHA Standards for Plumbing: PPE, Fall Protection & Hazard Communication 8.2 Trenching, Shoring, Soil Classifications & Confined Space Safety 8.3 Soldering, Brazing, Hot Work Permits & Jobsite Fire Prevention
9 Chapter 9: NC Contractor Business Law, Project Management & Liens (NASCLA / 21 NCAC 50)
9.1 NC Board Laws (NCGS 87-2), Administrative Rules (21 NCAC 50) & Disciplinary Actions 9.2 Estimating, Job Costing, Bidding & Contract Administration 9.3 North Carolina Mechanics' Lien Laws, Payment Bonds & Dispute Resolution 9.4 Financial Management, Tax Compliance, Workers' Compensation & Business Insurance 9.5 Business Formation, Entity Licensing & Startup Compliance in North Carolina 9.6 Employment Law, Payroll Compliance & Workforce Management 9.7 Project Management: Scheduling, Submittals, Documentation & Closeout 9.8 Surety Bonding, Risk Transfer & Claims Management 9.9 Environmental, Erosion Control & Jobsite Regulatory Compliance
10 Chapter 10: NC Residential Code Plumbing (Class II & Dwelling Practice)
10.1 NC Residential Code Scope, Administration, Materials & Water Supply for Dwellings 10.2 NC Residential Code DWV, Venting, Traps & Fuel Gas Provisions for Dwellings
1.5 Approved Materials, Standards, Joints & Connections
Key Takeaways Explain This Topic AI
Every pipe, fitting, and material must be listed in the applicable NC Plumbing Code table, bear a permanent identifying mark showing the referenced standard, and be used only in the application the table approves.
The NC amendment to Table 605.3 restricts underground copper water service to Type K, WK, L, and WL — Type M is a distribution-only tube in North Carolina.
ABS and PVC may not be solvent cemented to each other; the transition must be made with an approved mechanical or shielded coupling, and PVC requires primer plus cement while ABS uses cement only.
Fittings must not obstruct or change the direction of flow beyond their design: bushings in drainage, saddle fittings, heat-fusion joints on dissimilar materials, and any fitting with a ledge or shoulder in the waterway are prohibited.
Dielectric unions or approved dielectric fittings are required where copper joins galvanized steel to interrupt the galvanic cell that otherwise destroys the steel side of the joint.
Last updated: September 2026
1.5 Approved Materials, Standards, Joints & Connections
Quick Answer: North Carolina approves plumbing materials by table and by application . The same material can be legal in one place and illegal in another: PVC is approved for underground cold water service and for DWV , but not for interior potable distribution ; copper Type M is approved for interior water distribution but the NC amendment to Table 605.3 limits underground water service to Type K, WK, L, and WL . Every pipe and fitting must bear a permanent identifying mark showing the referenced standard. Joints must match the material: solvent cement with primer for PVC , cement only for ABS , never solvent cement between ABS and PVC (use an approved mechanical or shielded transition coupling). Bushings, saddle fittings, and any fitting with an obstruction, ledge, or shoulder in the waterway are prohibited in drainage , and dielectric fittings are required where copper meets galvanized steel.
The Listing, Marking & Application Rule
Before any sizing calculation matters, the material has to be legal for the job.
Listed and labeled. Pipe, tube, fittings, traps, fixtures, and appurtenances must conform to the standards referenced by the code and must be marked permanently with the manufacturer's mark or name and the referenced standard . Unmarked pipe is rejectable on sight.
Application-specific tables. The code does not maintain one master list. It maintains separate tables: water service pipe (605.3) , water distribution pipe (605.4) , fittings (605.5) , building sewer (702.2) , underground building drainage and vent (702.1) , aboveground drainage and vent (702.1) , and storm drainage. A candidate who memorises "PVC is approved" without the application will fail these questions.
Third-party certification. Potable-water components must comply with NSF 61 for health effects and NSF 372 for lead content. "Lead free" means a weighted average lead content of not more than 0.25 percent on wetted surfaces for pipe, fittings, and fixtures conveying water for human consumption.
Reused material. Used pipe, fittings, valves, and other materials may not be reused unless the code official finds them clean, free of defects, and conforming to the requirements for new material.
Material Approval by Application
- Material Underground water service Interior water distribution Sanitary drainage & vent Building sewer
- Copper Type K / L Approved Approved Approved (DWV weight also) Approved
Copper Type M Prohibited in NC (Table 605.3 amendment: below grade Type K, WK, L, WL) Approved Approved Not typical
- Copper Type DWV Prohibited Prohibited Approved (non-pressure) Not typical
- PEX / PE-RT (SDR 9) Approved Approved Not applicable Not applicable
- CPVC (CTS) Approved Approved (hot and cold) Not applicable Not applicable
- PVC pressure pipe Approved (cold only) Prohibited Approved as DWV schedule 40 Approved
- PE / HDPE Approved (cold only) Prohibited Not applicable Approved (SDR pressure-rated)
- ABS Rarely used Prohibited Approved Approved
- Cast iron (hub and hubless) Not applicable Not applicable Approved Approved
- Galvanized steel Legacy Legacy, corrodes internally Legacy only Not permitted new
- Ductile iron Approved (3 inches and larger typical) Commercial mains Not applicable Approved
Exam Trap — The Same Letter, Two Answers. "Is PVC approved?" is an incomplete question. PVC is approved for underground cold water service and for DWV and building sewer , and it is prohibited for interior potable water distribution and for hot water. Read the application in the stem before choosing.
Joining Methods by Material
Material Approved joints Critical detail
Copper tube Soldered, brazed, press-connect, flared, mechanical (compression), grooved Potable water solder and flux must be lead free (not more than 0.2 percent lead in solder and flux). Braze where the joint is exposed to temperatures a 50/50 solder cannot survive.
PVC Primer plus solvent cement (ASTM D2564 cement, F656 primer); threaded, mechanical, or gasketed for specific products The purple primer is required and is what an inspector looks for. Interference-fit the joint, apply cement to both surfaces, insert with a quarter turn, hold, and let the set and cure times pass before pressure.
ABS Solvent cement (ASTM D2235) — no primer Applying PVC primer to ABS does not make an ABS/PVC joint legal.
ABS to PVC Approved transition fitting only — mechanical or shielded coupling Solvent cementing ABS directly to PVC is prohibited; the two resins do not chemically weld and the joint fails under thermal cycling.
CPVC Solvent cement listed for CPVC (ASTM F493) CPVC cement is not interchangeable with PVC cement.
PEX Cold-expansion (ASTM F1960), copper crimp ring (F1807), stainless clamp (F2098), push-fit No solvent cement, no heat. PEX must be kept out of sunlight and away from the water heater flue; use a metallic transition nipple at the heater.
PE / HDPE Heat fusion (butt, socket, electrofusion), insert fittings with two stainless clamps, mechanical compression Heat fusion is only permitted between like materials of like grade.
Cast iron hubless Shielded couplings with stainless bands, torqued to the manufacturer's value Support requirements are stricter than for hub-and-spigot; every joint carries the alignment.
Cast iron hub and spigot Compression gasket or lead and oakum Lead-and-oakum joints are poured and caulked, not "packed and hoped."
Galvanized steel / brass Threaded joints with approved joint compound or tape applied to male threads only Compound on female threads ends up inside the waterway.
Prohibited Joints & Fittings
The code lists these explicitly, and they are dependable exam material because each has a clear physical reason.
Cement or concrete joints — no longer approved for new drainage work.
Mastic or hot-pour bituminous joints — not approved for pressure or drainage joints.
Joints between different diameters made with fittings not approved for the transition — an increaser used as a reducer in drainage creates a solids trap.
Saddle-type fittings — a hole cut in the side of a drain and covered with a strapped saddle is prohibited. Every branch must be made with an approved fitting.
Solvent-cement joints between different plastics (for example ABS to PVC) — mechanical transition required.
Heat-fusion joints between dissimilar materials — fusion works only within a material family.
Drainage fittings with an obstruction, ledge, shoulder, or reduction in the waterway — including double hubs on a vertical drain, tees or crosses with a straight-through waterway used in horizontal drainage, and bushings in drainage .
Threaded drainage joints except where recessed drainage fittings are used.
Exam Trap — Sanitary Tee Direction. A sanitary tee is designed for a horizontal branch entering a vertical drain . It is prohibited for a horizontal-to-horizontal connection and at the base of a stack, where a long-turn fitting or a combination wye and eighth bend must be used. This is the single most reliably asked fitting question on IPC-based exams and is covered again in Chapter 4.
Dissimilar Metals & Transition Connections
Where copper is joined directly to galvanized steel, the two metals plus the water form a galvanic cell . Zinc and then iron corrode preferentially, and the steel side of the joint fails from the inside out — often within a few years in North Carolina's relatively soft municipal water.
Dielectric union or approved dielectric fitting is required at copper-to-steel connections in water piping. A brass adapter alone is not a dielectric.
Brass nipple transitions of adequate length are accepted by some jurisdictions as an alternative to a dielectric union; confirm locally before relying on the practice.
Underground transitions are the worst place to depend on dielectric protection. Where a copper service ties to a legacy galvanized entry, replace the galvanized rather than couple to it.
Plastic-to-metal at appliances. PEX and CPVC connect to water heaters through listed transition fittings and, for PEX, a metallic nipple that keeps the tubing away from flue heat.
Dielectric protection is not corrosion protection for the pipe body. Where soil is corrosive, copper service tubing still needs sleeving or approved protective coating, and steel gas piping still needs coating and cathodic considerations covered in Chapter 7.