Study guide

4.2 Drainage Fixture Unit (DFU) Sizing for Building Drains, Sewers & Stacks

North Carolina Plumbing Contractor Exam Class I & Class II

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview, Administration & General Code Regulations

1.1 NC Plumbing Licensing, Board Rules & Exam Structure 1.2 General Regulations, Piping Support, Trenching & Protection 1.3 Plumbing Mathematics, Grade Calculations & Isometric Plan Reading 1.4 Permits, Plan Review, Required Inspections & Code-Mandated Tests 1.5 Approved Materials, Standards, Joints & Connections

2 Chapter 2: Fixtures, Faucets, Fixture Fittings & Water Heaters

2.1 Minimum Fixture Requirements, Accessibility (ADA) & Rough-In Spacing 2.2 Fixture Installation, Setting Clearances & Flushometer Valves 2.3 Water Heater Sizing, Temperature & Pressure Relief (T&P) Valves & Safety Devices

3 Chapter 3: Water Supply and Distribution & Backflow Prevention

3.1 Water Service Sizing, Materials & Pressure Regulation 3.2 Water Supply Fixture Units (WSFU) & Pipe Sizing Methods 3.3 Cross-Connection Control, Backflow Prevention Devices & Hazards 3.4 Hot and Cold Water Distribution Design & Pressure Loss Calculations

4 Chapter 4: Sanitary Drainage, Indirect Waste, Sumps & Ejectors

4.1 Drainage System Principles, Flow Velocities & Minimum Slope Requirements 4.2 Drainage Fixture Unit (DFU) Sizing for Building Drains, Sewers & Stacks 4.3 Cleanout Sizing, Locations, Clearances & Installation Standards 4.4 Sewage Sumps, Macerating Systems & Indirect/Special Waste 4.5 Building Sewers, Sewer Connections & Private Sewage Disposal

5 Chapter 5: Vents and Venting Systems

5.1 Venting Principles, Termination & Minimum Sizing 5.2 Wet Venting, Common Venting & Stack Vent Systems 5.3 Circuit & Loop Venting, Combination Waste & Vent Systems 5.4 Island Fixture Venting & Air Admittance Valves (AAVs)

6 Chapter 6: Traps, Interceptors, Separators & Storm Drainage

6.1 Trap Design, Prohibited Traps & Trap Arm Developed Lengths 6.2 Grease Interceptors, Oil Separators & Sand Traps 6.3 Storm Drainage Sizing, Roof Drains & Secondary (Emergency) Overflow Systems

7 Chapter 7: Fuel Gas Piping & Appliance Venting (NC IFGC)

7.1 Fuel Gas Fundamentals, Materials, Jointing & Mandatory Pressure Testing 7.2 Fuel Gas Pipe Sizing: Longest Length & Branch Sizing Methods 7.3 Combustion Air Requirements: Indoor, Outdoor & Engineered Openings 7.4 Fuel Gas Appliance Venting: Category I–IV Systems, Chimneys & Clearances

8 Chapter 8: Safety, Excavation & Jobsite Practices (OSHA 1926)

8.1 OSHA Standards for Plumbing: PPE, Fall Protection & Hazard Communication 8.2 Trenching, Shoring, Soil Classifications & Confined Space Safety 8.3 Soldering, Brazing, Hot Work Permits & Jobsite Fire Prevention

9 Chapter 9: NC Contractor Business Law, Project Management & Liens (NASCLA / 21 NCAC 50)

9.1 NC Board Laws (NCGS 87-2), Administrative Rules (21 NCAC 50) & Disciplinary Actions 9.2 Estimating, Job Costing, Bidding & Contract Administration 9.3 North Carolina Mechanics' Lien Laws, Payment Bonds & Dispute Resolution 9.4 Financial Management, Tax Compliance, Workers' Compensation & Business Insurance 9.5 Business Formation, Entity Licensing & Startup Compliance in North Carolina 9.6 Employment Law, Payroll Compliance & Workforce Management 9.7 Project Management: Scheduling, Submittals, Documentation & Closeout 9.8 Surety Bonding, Risk Transfer & Claims Management 9.9 Environmental, Erosion Control & Jobsite Regulatory Compliance

10 Chapter 10: NC Residential Code Plumbing (Class II & Dwelling Practice)

10.1 NC Residential Code Scope, Administration, Materials & Water Supply for Dwellings 10.2 NC Residential Code DWV, Venting, Traps & Fuel Gas Provisions for Dwellings

4.2 Drainage Fixture Unit (DFU) Sizing for Building Drains, Sewers & Stacks

Key Takeaways Explain This Topic AI

Drainage Fixture Units (DFUs) represent the probable discharge load of plumbing fixtures based on flow volume, discharge duration, and cycle frequency, with continuous discharge converted at 2 DFUs per 1 GPM.

Individual fixture DFU values under NCSPC Table 709.1 include: water closet = 4 DFU (private 1.6 GPF) or 6 DFU (public/flushometer), lavatory = 1 DFU, kitchen sink = 2 DFU, shower = 2 DFU, and domestic clothes washer = 3 DFU.

Drainage stack sizing (NCSPC Table 710.1(2)) restricts vertical stack capacity based on building height and branch intervals: a 3-inch stack accommodates up to 24 DFUs on ≤ 3 stories (or per branch interval) and 48 DFUs total; a 4-inch stack accommodates 240 DFUs on ≤ 3 stories and 500 DFUs total.

Stack offsets exceeding 45 degrees from vertical must be sized as horizontal building drains, require a 'no connection zone' within 2 feet above and below the offset, and require yoke/relief venting in buildings with 5 or more branch intervals.

Last updated: September 2026

4.2 Drainage Fixture Unit (DFU) Sizing for Building Drains, Sewers & Stacks

Quick Answer: Sanitary drainage systems are sized using Drainage Fixture Units (DFU) under North Carolina Plumbing Code Chapter 7. Fixture loads range from 1 DFU for a private lavatory to 4 DFU (private 1.6 GPF gravity WC) and 6 DFU (public flushometer WC). Continuous flow discharges convert at 2 DFU per 1 GPM . Vertical drainage stacks are sized by branch intervals and total building height: a 3-inch stack accommodates a maximum of 24 DFUs for ≤ 3 \le 3 ≤ 3 stories (or per branch interval) and 48 DFUs total for multi-story stacks; a 4-inch stack supports 240 DFUs for ≤ 3 \le 3 ≤ 3 stories and 500 DFUs total . Offsets exceeding 45 degrees must be sized as horizontal building drains and require a 2-foot no-connection zone above and below the offset.

The Drainage Fixture Unit (DFU) System

The Drainage Fixture Unit (DFU) is a dimensionless hydraulic weighting metric developed by Dr. Roy B. Hunter. Because plumbing fixtures operate intermittently rather than continuously, pipe diameters would be grossly oversized if sized for simultaneous maximum discharge. The DFU system calculates the statistical probability of simultaneous fixture operation.

1 DFU Equivalence: Represents a discharge volume of approximately 7.5 Gallons Per Minute (GPM) or 1.0 cubic foot per minute of intermittent waste flow.

Continuous / Semi-Continuous Discharges: When equipment (sump pumps, commercial air conditioning condensate, air compressors, or industrial wash tanks) discharges continuously or cyclically into the sanitary drainage system, each 1.0 GPM of flow is converted to 2.0 DFUs : Total DFU (Continuous Flow) = Continuous Flow (GPM) × 2.0 DFU/GPM \text{Total DFU (Continuous Flow)} = \text{Continuous Flow (GPM)} \times 2.0\text{ DFU/GPM} Total DFU (Continuous Flow) = Continuous Flow (GPM) × 2.0 DFU/GPM

Example: A commercial water-cooled condenser pump continuously discharging 12.0 GPM 12.0\text{ GPM} 12.0 GPM into a floor drain adds 12.0 × 2 = 24.0 DFUs 12.0 \times 2 = 24.0\text{ DFUs} 12.0 × 2 = 24.0 DFUs to the drainage branch.

Master Fixture DFU Allocations (NCSPC Table 709.1 & 709.2)

  • Plumbing Fixture Type Occupancy Type / Specification DFU Value Minimum Trap & Drain Size
  • Water Closet (Gravity Tank) Private (1.6 GPF or less) 4 DFU 3 inches
  • Water Closet (Gravity Tank) Private (> 1.6 GPF / older) 4 DFU 3 inches
  • Water Closet (Flushometer Valve) Public (1.6 GPF or Flushometer Tank) 4 DFU 3 inches
  • Water Closet (Flushometer Valve) Public (> 1.6 GPF / older standard) 6 DFU 3 inches
  • Lavatory (Handwash Sink) Private 1 DFU 1-1/4 inches
  • Lavatory (Handwash Sink) Public / Commercial 1 DFU (or 2 DFU group) 1-1/4 inches
  • Kitchen Sink (Domestic) Private (with or without food disposer) 2 DFU 1-1/2 inches
  • Kitchen Sink (Commercial) Public / Restaurant (Scullery, pot wash) 3 DFU 1-1/2 or 2 inches
  • Bathtub (with or without shower) Private 2 DFU 1-1/2 inches
  • Shower Stall (Individual) Private / Public (Flow rate ≤ 5.7 \le 5.7 ≤ 5.7 GPM) 2 DFU 2 inches
  • Multi-head Shower (per head) Public / Institutional 2 DFU / head 2 or 3 inches
  • Clothes Washer (Automatic) Domestic (Residential Standpipe) 3 DFU 2 inches
  • Clothes Washer (Commercial) Laundromat / Hotel (per machine) 3 to 4 DFU 2 or 3 inches
  • Floor Drain General (with 2" minimum trap) 2 DFU 2 inches
  • Service Sink / Mop Basin Commercial / Custodial 2 DFU (flush rim: 3 DFU) 2 or 3 inches
  • Urinal (1.0 GPF or Waterless) Public 2 DFU 2 inches
  • Urinal (Flushometer > 1.0 GPF) Public / Commercial 4 DFU 2 inches
  • Drinking Fountain Public 0.5 DFU 1-1/4 inches

Exam Trap — Water Closet Minimum Pipe Size: A water closet must never discharge into a pipe smaller than 3 inches nominal diameter . A 3-inch horizontal branch can carry a maximum of two (2) water closets ; any branch serving three or more water closets must be sized at 4 inches minimum .

Horizontal Fixture Branches & Drainage Stacks (NCSPC Table 710.1(2))

Sanitary piping is divided into horizontal fixture branches, vertical stacks, and building drains. +-------------------------------------------------------------------------+

  • | SANITARY DRAINAGE SYSTEM NOMENCLATURE |
  • +-------------------------------------------------------------------------+
  • | |
  • | [ VENT TERMINAL ] |
  • | │ |
  • | ▼ |
  • | ┌──────────────────────────┐ |
  • | │ VERTICAL STACK VENT │ |
  • | └────────────┬─────────────┘ |
  • | FLOOR 3 │ |
  • | ══════════════════════════════╪════════════════════════════════════ |
  • | [Horizontal Branch] │ |
  • | (───) ─────────────────────┤ ◄ Branch Interval 3 |
  • | │ (≥ 8 ft vertical drop) |
  • | FLOOR 2 │ |
  • | ══════════════════════════════╪════════════════════════════════════ |
  • | [Horizontal Branch] │ |
  • | (───) ─────────────────────┤ ◄ Branch Interval 2 |
  • | │ |
  • | FLOOR 1 │ |
  • | ══════════════════════════════╪════════════════════════════════════ |
  • | [Horizontal Branch] │ |
  • | (───) ─────────────────────┤ ◄ Branch Interval 1 |
  • | │ |
  • | BASEMENT ▼ |
  • | ═══════════════════════════[LONG TURN 90°]═════════════════════════ |
  • | │ |
  • | ▼ |
  • | [BUILDING DRAIN (Horizontal)] |
  • | ────────────────────────────────────────► |
  • | ══════════════════════════════╪══════════════════════ Foundation Wall |
  • | (30" outside) ────┘ |
  • | ▼ |
  • | [BUILDING SEWER (Underground)] |
  • | |
  • +-------------------------------------------------------------------------+

Definitions:

Branch Interval: A vertical length of stack, at least 8 feet in height (typically one building story), within which the horizontal branches from one floor or story are connected to the stack.

Horizontal Branch: A drainage pipe extending laterally from a plumbing fixture or battery of fixtures to the vertical stack or building drain.

Soil Stack: A vertical drainage pipe that receives discharge from water closets or urinals (human excreta).

Waste Stack: A vertical drainage pipe that receives only liquid waste free of fecal matter (sinks, lavatories, showers, tubs).

Master Horizontal Branch and Vertical Stack Sizing Table (NCSPC Table 710.1(2))

Nominal Pipe Diameter Max DFUs on a Horizontal Branch Max DFUs for Stack ≤ 3 \le 3 ≤ 3 Stories (or 1 Branch Interval) Max DFUs for Stack > 3 > 3 > 3 Stories (Total Stack) Max DFUs per Branch Interval on Multi-Story Stack

  • 1-1/4 inches 1 DFU 2 DFU 2 DFU 1 DFU
  • 1-1/2 inches 3 DFU 4 DFU 8 DFU 2 DFU
  • 2 inches 6 DFU 10 DFU 24 DFU 6 DFU
  • 2-1/2 inches 12 DFU 20 DFU 42 DFU 9 DFU
  • 3 inches 20 DFU (max 2 WCs) 24 DFU (max 2 WCs) 48 DFU (max 6 WCs) 24 DFU (max 2 WCs)
  • 4 inches 160 DFU 240 DFU 500 DFU 90 DFU
  • 5 inches 360 DFU 540 DFU 1,100 DFU 200 DFU
  • 6 inches 620 DFU 960 DFU 1,900 DFU 350 DFU
  • 8 inches 1,400 DFU 2,200 DFU 3,600 DFU 600 DFU

Key Exam Rules for Stacks:

A 3-inch vertical stack can carry up to 24 DFUs in a single branch interval (or in a building ≤ 3 \le 3 ≤ 3 stories). On a multi-story building ( > 3 > 3 > 3 stories), the 3-inch stack can carry a maximum of 48 DFUs total , provided no single branch interval exceeds 24 DFUs .

A 4-inch vertical stack can carry up to 240 DFUs in a ≤ 3 \le 3 ≤ 3 story building, and up to 500 DFUs total in a multi-story building, with a maximum of 90 DFUs per branch interval .

Building Drains & Building Sewers (NCSPC Table 710.1(1))

Building Drain: The lowest part of a building drainage system that receives wastewater from soil, waste, and other drainage pipes inside the walls and extends to a point 30 inches (2.5 feet) outside the exterior building foundation wall.

Building Sewer: The continuation of the drainage piping starting 30 inches outside the building foundation wall and extending to the municipal sewer main, public manhole, or private septic tank.

Master Building Drain & Sewer Sizing Table (Maximum Allowable DFU Load)

Nominal Pipe Diameter 1/16 in/ft Slope (0.52%) 1/8 in/ft Slope (1.04%) 1/4 in/ft Slope (2.08%) 1/2 in/ft Slope (4.17%)

  • 1-1/4 inches — — 1 DFU 1 DFU
  • 1-1/2 inches — — 3 DFU 3 DFU
  • 2 inches — — 21 DFU 26 DFU
  • 2-1/2 inches — — 24 DFU 31 DFU
  • 3 inches — 36 DFU (max 2 WCs) 42 DFU (max 2 WCs) 50 DFU (max 2 WCs)
  • 4 inches — 180 DFU 216 DFU 250 DFU
  • 5 inches — 390 DFU 480 DFU 575 DFU
  • 6 inches — 700 DFU 840 DFU 1,000 DFU
  • 8 inches 1,400 DFU 2,500 DFU 2,900 DFU 3,500 DFU
  • 10 inches 2,500 DFU 4,500 DFU 5,300 DFU 6,400 DFU
  • 12 inches 3,900 DFU 7,000 DFU 8,300 DFU 10,000 DFU

Note: 1/16 in/ft slope is prohibited for pipes 6 inches or smaller under standard code.

Offsets in Vertical Drainage Stacks

When structural obstructions (beams, elevator shafts, or architectural setbacks) require a vertical drainage stack to shift horizontally, the offset is classified by its angle: +-------------------------------------------------------------------------+

  • | STACK OFFSET CONFIGURATIONS |
  • +-------------------------------------------------------------------------+
  • | |
  • | CASE 1: OFFSET ≤ 45° (Treated as Vertical Stack) |
  • | |
  • | │ Upper Stack Section |
  • | │ |
  • | ╲ 45° Offset (No sizing change; no relief vents required) |
  • | ╲ |
  • | │ Lower Stack Section |
  • | ▼ |
  • | |
  • | CASE 2: OFFSET > 45° (Treated as Horizontal Building Drain) |
  • | |
  • | │ Upper Stack Section (Sized for upper DFUs) |
  • | ▼ |
  • | ┌───┐ ◄── 2-ft "No Connection Zone" |
  • | └───┘ |
  • | ═════════════════════════════════════ Horizontal Offset Section |
  • | (Sized as Building Drain per Table 710.1(1); |
  • | Relief Vent & Yoke Vent required if ≥ 5 branch intervals) |
  • | ┌───┐ |
  • | └───┘ ◄── 2-ft "No Conn Zone" |
  • | │ Lower Stack Section |
  • | ▼ (Sized for Total DFUs) |
  • +-------------------------------------------------------------------------+
  • 1. Offsets of 45 ∘ 45^\circ 4 5 ∘ or Less from Vertical (NCSPC 711.1)

Treated hydraulically as a continuous vertical stack.

The pipe size does not change through the offset.

No auxiliary relief vents are required.

2. Offsets of More than 45 ∘ 45^\circ 4 5 ∘ from Vertical (NCSPC 711.2)

The horizontal offset section experiences hydraulic jump, deceleration, and pipe-full conditions.

Sizing of the Horizontal Offset: Must be sized as a horizontal building drain from Table 710.1(1) based on the total DFU load entering from the upper stack.

Sizing of Lower Stack: Must be sized as a vertical stack for the combined total DFU load of all fixtures above plus any fixtures connecting below the offset.

The 2-Foot No-Connection Zone (NCSPC 711.2): No horizontal fixture branch may connect to the vertical stack within 2 feet above or 2 feet below the horizontal offset.

Relief and Yoke Venting (Buildings ≥ 5 \ge 5 ≥ 5 branch intervals):

A relief vent must connect to the upper stack section above the offset.

A yoke vent must connect to the lower stack section below the offset to equalize positive pressure caused by the deceleration of falling waste.

Step-by-Step Worked Sizing Example

Project Scenario:

A 3-story commercial office building in Raleigh, NC has identical fixture batteries on each floor:

Per Floor Fixtures:

3 Flushometer Water Closets (Public, 1.6 GPF): 3 × 4 DFU = 12 DFU 3 \times 4\text{ DFU} = 12\text{ DFU} 3 × 4 DFU = 12 DFU

  • 2 Urinals (Public 1.0 GPF): 2 × 2 DFU = 4 DFU 2 \times 2\text{ DFU} = 4\text{ DFU} 2 × 2 DFU = 4 DFU
  • 3 Public Lavatories: 3 × 1 DFU = 3 DFU 3 \times 1\text{ DFU} = 3\text{ DFU} 3 × 1 DFU = 3 DFU
  • 1 Custodial Mop Sink: 1 × 2 DFU = 2 DFU 1 \times 2\text{ DFU} = 2\text{ DFU} 1 × 2 DFU = 2 DFU
  • 1 Drinking Fountain: 1 × 0.5 DFU = 0.5 DFU 1 \times 0.5\text{ DFU} = 0.5\text{ DFU} 1 × 0.5 DFU = 0.5 DFU

Basement Level: A clear-water pump discharges groundwater continuously into a dedicated gravity floor drain at 10 GPM ( 10 × 2 = 20 DFU 10 \times 2 = 20\text{ DFU} 10 × 2 = 20 DFU ).

Drainage Layout: All 3 floors connect to a single vertical drainage stack that drops into a horizontal building drain sloped at 1/4 inch per foot .

Step-by-Step Sizing Solution:

Step 1: Calculate DFU Load per Floor (Branch Interval) Floor Load = 12 (WCs) + 4 (Urinals) + 3 (Lavs) + 2 (Mop Sink) + 0.5 (DF) = 21.5 DFU per floor \text{Floor Load} = 12\text{ (WCs)} + 4\text{ (Urinals)} + 3\text{ (Lavs)} + 2\text{ (Mop Sink)} + 0.5\text{ (DF)} = \mathbf{21.5\text{ DFU per floor}} Floor Load = 12 (WCs) + 4 (Urinals) + 3 (Lavs) + 2 (Mop Sink) + 0.5 (DF) = 21.5 DFU per floor

Step 2: Size the Horizontal Fixture Branch on Each Floor

Consult Table 710.1(2) under "Max DFUs on Horizontal Branch":

A 3-inch branch allows up to 20 DFU 20\text{ DFU} 20 DFU and a maximum of 2 water closets .

Floor branch carries 21.5 DFU 21.5\text{ DFU} 21.5 DFU and 3 water closets .

Selection: Horizontal floor branch must be 4 inches nominal diameter (allows up to 160 DFU 160\text{ DFU} 160 DFU ). A 3-inch pipe is prohibited because it carries 3 water closets and exceeds 20 DFU.

Step 3: Size the Vertical Drainage Stack

Total Fixture Load on Stack (Floors 1, 2, and 3): Total Stack Load = 3 floors × 21.5 DFU = 64.5 DFU \text{Total Stack Load} = 3 \text{ floors} \times 21.5\text{ DFU} = \mathbf{64.5\text{ DFU}} Total Stack Load = 3 floors × 21.5 DFU = 64.5 DFU

Evaluate Stack Capacity from Table 710.1(2) for a 3-story building ( ≤ 3 \le 3 ≤ 3 stories column):

3-inch stack: Maximum allowable = 24 DFU 24\text{ DFU} 24 DFU (and max 2 WCs).

4-inch stack: Maximum allowable = 240 DFU 240\text{ DFU} 240 DFU .

Selection: The vertical stack must be 4 inches nominal diameter (since 64.5 DFU exceeds the 24 DFU limit of a 3" stack).

Step 4: Size the Horizontal Building Drain

Total Building Load = Stack Load ( 64.5 DFU 64.5\text{ DFU} 64.5 DFU ) + Continuous Basement Pump ( 20.0 DFU 20.0\text{ DFU} 20.0 DFU ) = 84.5 DFU .

Slope = 1/4 inch per foot .

Consult Table 710.1(1) under "1/4 in/ft Slope":

3-inch pipe at 1/4" slope = 42 DFU 42\text{ DFU} 42 DFU max (insufficient).

4-inch pipe at 1/4" slope = 216 DFU 216\text{ DFU} 216 DFU max ( 84.5 DFU ≤ 216 DFU 84.5\text{ DFU} \le 216\text{ DFU} 84.5 DFU ≤ 216 DFU , fully compliant).

Selection: The horizontal building drain must be 4 inches nominal diameter .

Exam Traps & Pro-Tips

Warning

Common Exam Pitfall #1 — 3-Inch Branch Water Closet Limit: A 3-inch horizontal drainage branch can carry a maximum of 20 DFUs , but code explicitly limits it to a maximum of two (2) water closets . If an exam question presents a branch with 3 water closets rated at 4 DFU each ( 12 DFU 12\text{ DFU} 12 DFU total), the branch cannot be 3 inches—it must be sized up to 4 inches .

Important

Exam Pro-Tip #2 — Continuous GPM Conversion: Whenever an exam problem mentions continuous discharge (e.g., cooling tower bleed, sump pump, or process waste), multiply the GPM by 2.0 to obtain the DFU value ( 15 GPM = 30 DFU 15\text{ GPM} = 30\text{ DFU} 15 GPM = 30 DFU ).

Note

Exam Pro-Tip #3 — Building Drain vs. Sewer Boundary: The exact legal and technical boundary between the building drain and the building sewer is 30 inches (2.5 feet) beyond the exterior surface of the building foundation wall.