Study guide
3.2 Water Supply Fixture Units (WSFU) & Pipe Sizing Methods
North Carolina Plumbing Contractor Exam Class I & Class II
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview, Administration & General Code Regulations
1.1 NC Plumbing Licensing, Board Rules & Exam Structure 1.2 General Regulations, Piping Support, Trenching & Protection 1.3 Plumbing Mathematics, Grade Calculations & Isometric Plan Reading 1.4 Permits, Plan Review, Required Inspections & Code-Mandated Tests 1.5 Approved Materials, Standards, Joints & Connections
2 Chapter 2: Fixtures, Faucets, Fixture Fittings & Water Heaters
2.1 Minimum Fixture Requirements, Accessibility (ADA) & Rough-In Spacing 2.2 Fixture Installation, Setting Clearances & Flushometer Valves 2.3 Water Heater Sizing, Temperature & Pressure Relief (T&P) Valves & Safety Devices
3 Chapter 3: Water Supply and Distribution & Backflow Prevention
3.1 Water Service Sizing, Materials & Pressure Regulation 3.2 Water Supply Fixture Units (WSFU) & Pipe Sizing Methods 3.3 Cross-Connection Control, Backflow Prevention Devices & Hazards 3.4 Hot and Cold Water Distribution Design & Pressure Loss Calculations
4 Chapter 4: Sanitary Drainage, Indirect Waste, Sumps & Ejectors
4.1 Drainage System Principles, Flow Velocities & Minimum Slope Requirements 4.2 Drainage Fixture Unit (DFU) Sizing for Building Drains, Sewers & Stacks 4.3 Cleanout Sizing, Locations, Clearances & Installation Standards 4.4 Sewage Sumps, Macerating Systems & Indirect/Special Waste 4.5 Building Sewers, Sewer Connections & Private Sewage Disposal
5 Chapter 5: Vents and Venting Systems
5.1 Venting Principles, Termination & Minimum Sizing 5.2 Wet Venting, Common Venting & Stack Vent Systems 5.3 Circuit & Loop Venting, Combination Waste & Vent Systems 5.4 Island Fixture Venting & Air Admittance Valves (AAVs)
6 Chapter 6: Traps, Interceptors, Separators & Storm Drainage
6.1 Trap Design, Prohibited Traps & Trap Arm Developed Lengths 6.2 Grease Interceptors, Oil Separators & Sand Traps 6.3 Storm Drainage Sizing, Roof Drains & Secondary (Emergency) Overflow Systems
7 Chapter 7: Fuel Gas Piping & Appliance Venting (NC IFGC)
7.1 Fuel Gas Fundamentals, Materials, Jointing & Mandatory Pressure Testing 7.2 Fuel Gas Pipe Sizing: Longest Length & Branch Sizing Methods 7.3 Combustion Air Requirements: Indoor, Outdoor & Engineered Openings 7.4 Fuel Gas Appliance Venting: Category I–IV Systems, Chimneys & Clearances
8 Chapter 8: Safety, Excavation & Jobsite Practices (OSHA 1926)
8.1 OSHA Standards for Plumbing: PPE, Fall Protection & Hazard Communication 8.2 Trenching, Shoring, Soil Classifications & Confined Space Safety 8.3 Soldering, Brazing, Hot Work Permits & Jobsite Fire Prevention
9 Chapter 9: NC Contractor Business Law, Project Management & Liens (NASCLA / 21 NCAC 50)
9.1 NC Board Laws (NCGS 87-2), Administrative Rules (21 NCAC 50) & Disciplinary Actions 9.2 Estimating, Job Costing, Bidding & Contract Administration 9.3 North Carolina Mechanics' Lien Laws, Payment Bonds & Dispute Resolution 9.4 Financial Management, Tax Compliance, Workers' Compensation & Business Insurance 9.5 Business Formation, Entity Licensing & Startup Compliance in North Carolina 9.6 Employment Law, Payroll Compliance & Workforce Management 9.7 Project Management: Scheduling, Submittals, Documentation & Closeout 9.8 Surety Bonding, Risk Transfer & Claims Management 9.9 Environmental, Erosion Control & Jobsite Regulatory Compliance
10 Chapter 10: NC Residential Code Plumbing (Class II & Dwelling Practice)
10.1 NC Residential Code Scope, Administration, Materials & Water Supply for Dwellings 10.2 NC Residential Code DWV, Venting, Traps & Fuel Gas Provisions for Dwellings
3.2 Water Supply Fixture Units (WSFU) & Pipe Sizing Methods
Key Takeaways Explain This Topic AI
Water Supply Fixture Units (WSFU) quantify intermittent fixture demand based on Hunter's probability curve, converting cumulative fixture values into continuous peak demand in Gallons Per Minute (GPM).
Systems with flushometer valves generate significantly higher peak flow demand (Hunter's Curve 1) than flush tank systems (Curve 2) for equivalent WSFU totals.
Pipe sizing under the Developed Length Friction Loss method subtracts elevation loss (0.433 psi/ft), meter loss, backflow loss, and minimum fixture residual pressure from static pressure to find allowable friction loss per 100 feet.
Total equivalent pipe length equals the linear developed length plus fitting resistance, standardly calculated by adding a 50% allowance (Developed Length × 1.50).
Maximum permissible water velocities are strictly capped at 8.0 feet per second (fps) for cold water and 5.0 fps for hot water copper piping to prevent destructive erosion-corrosion and cavitation.
Last updated: September 2026
3.2 Water Supply Fixture Units (WSFU) & Pipe Sizing Methods
Quick Answer: Potable water piping is engineered using Water Supply Fixture Units (WSFU) , developed by Dr. Roy B. Hunter to convert intermittent fixture usage into continuous Peak Demand (GPM) . Sizing requires calculating the total equivalent length (developed length + 50% fitting allowance), deducting all fixed pressure drops ( 0.433 psi/ft elevation loss , water meter loss, backflow preventer loss, and fixture residual operating pressure), and determining the available friction loss per 100 feet ( Δ P 100 \Delta P_{100} Δ P 100 ) . Pipe diameters are selected from friction loss charts while strictly observing maximum velocity limits: 8.0 fps for cold water and 5.0 fps for hot water copper to prevent erosion-corrosion.
Principles of Hydraulic Sizing & Hunter's Curve
Plumbing fixtures in buildings operate intermittently. If water distribution systems were sized by simply adding the maximum flow rates of all fixtures running concurrently, the resulting piping would be massively oversized, expensive, and subject to stagnant water quality degradation. In 1940, Dr. Roy B. Hunter of the National Bureau of Standards published Report BMS66, establishing the Water Supply Fixture Unit (WSFU) methodology based on binomial probability distribution.
WSFU Definition: A dimensionless numerical weighting factor assigned to a plumbing fixture representing its hydraulic load demand, taking into account volume of discharge, duration of a single operating cycle, and the average frequency of use.
Hunter's Curve: Translates cumulative WSFU into an expected peak instantaneous flow rate in Gallons Per Minute (GPM) . +-------------------------------------------------------------------------+
- | HUNTER'S DEMAND CURVES |
- +-------------------------------------------------------------------------+
- | GPM |
- | 160 ┌───────────────────────────────────────────────────────────────┐ |
- | 140 │ │ |
- | 120 │ CURVE 1 │ |
- | 100 │ (Flushometers)────┤ |
- | 80 │ ──────── │ |
- | 60 │ ──────── │ |
- | 40 │ ────────── CURVE 2 │ |
- | 20 │ ────────── (Flush Tanks)───┤ |
- | 0 └────────┴─────────┴─────────┴─────────┴─────────┴─────────┴────┘ |
- | 0 50 100 150 200 250 300 WSFU |
- +-------------------------------------------------------------------------+
- Curve 1 (Flushometer Valves) vs. Curve 2 (Flush Tanks)
Curve 1 (Flushometer Systems): Flushometer valves flush in 4 to 9 seconds at instantaneous flow rates of 25 to 35 GPM. Because a single operating cycle demands immense instantaneous volume, the peak demand at low-to-medium WSFU is substantially higher.
Curve 2 (Flush Tank Systems): Flush tanks fill slowly over 45 to 90 seconds at 3 to 5 GPM through a ballcock/fill valve. Demand is smoothed out, resulting in lower peak GPM.
Master WSFU Allocation Table for Common Fixtures
Under North Carolina Plumbing Code Table E103.3(2) / IPC Section 604 , WSFU ratings depend on whether the fixture is installed in a private (residential dwelling unit) or public (commercial, assembly, institutional) occupancy, and whether cold or hot supply branches are being sized.
- Fixture Type Occupancy / Type Total WSFU Cold Supply WSFU Hot Supply WSFU Min. Supply Pipe Size
- Water Closet (Flushometer Valve) Public 5.0 5.0 — 1" nominal
- Water Closet (Flushometer Valve) Private 3.0 3.0 — 1" nominal
- Water Closet (Flush Tank / Gravity) Public 2.5 2.5 — 3/8" (1/2" branch)
- Water Closet (Flush Tank / Gravity) Private 1.5–2.2 1.5–2.2 — 3/8" (1/2" branch)
- Urinal (Flushometer 1.0 GPF) Public 3.0 3.0 — 3/4" nominal
- Lavatory (Handwash Basin) Public 1.0 0.75 0.75 3/8" (1/2" branch)
- Lavatory (Handwash Basin) Private 0.5 0.5 0.5 3/8" (1/2" branch)
- Kitchen Sink (Domestic) Private / Res. 1.5 1.0 1.0 1/2" nominal
- Kitchen Sink (Commercial / Scullery) Public / Rest. 3.0 2.25 2.25 1/2" or 3/4"
- Bathtub / Combination Shower Private 2.0 1.5 1.5 1/2" nominal
- Showerhead (Multi-stall Group) Public 2.0 (per head) 1.5 1.5 1/2" nominal
- Clothes Washer (Domestic) Private 2.0 1.5 1.5 1/2" nominal
- Mop Service Basin / Service Sink Commercial 2.5 2.0 2.0 1/2" nominal
- Hose Bibb / Sillcock (First) General 2.5 2.5 — 1/2" nominal
- Hose Bibb (Each additional) General 1.0 1.0 — 1/2" nominal
Exam Sizing Rule: When sizing a main building supply or combined cold-and-hot trunk line, use the Total WSFU column. When sizing a dedicated cold water branch or dedicated hot water branch, use the individual Cold WSFU or Hot WSFU values. Note that individual cold and hot fixture units do not add up arithmetically to the total fixture units because both hot and cold faucets are rarely drawn at maximum capacity simultaneously.
WSFU to GPM Peak Demand Conversion Table
- Total WSFU Curve 1: Flushometer System (GPM) Curve 2: Flush Tank System (GPM)
- 5 15.0 3.0
- 10 27.0 8.0
- 20 35.0 14.0
- 30 42.0 20.0
- 40 46.0 24.0
- 50 50.0 28.0
- 75 59.0 37.0
- 100 65.0 43.5
- 150 77.0 54.0
- 200 86.0 65.0
- 300 101.0 81.0
- 500 124.0 108.0
- Pipe Sizing Methodologies
The North Carolina Plumbing Code recognizes two primary design methodologies for sizing water distribution networks:
1. Simplified / Table Sizing Method (NC Plumbing Code Table 604.10.1 / IPC)
Application: Restricted to simple residential, single-family, and small commercial structures where developed piping length does not exceed code limits (typically ≤ 150 to 200 feet \le 150\text{ to } 200\text{ feet} ≤ 150 to 200 feet ) and static municipal pressure falls into standard pressure ranges (30–39 psi, 40–49 psi, 50–59 psi, ≥ 60 psi \ge 60\text{ psi} ≥ 60 psi ).
Procedure: Plumbers cross-reference the static pressure tier, meter size, and developed length directly against code tables to find the maximum allowable WSFU for 3/4", 1", 1-1/4", or 1-1/2" pipe sizes.
2. Developed Length Friction Loss Method (Engineered / Comprehensive Method)
Used for complex, multi-story, commercial, or hydraulically demanding installations. Follows a systematic 6-step mathematical sequence: +-------------------------------------------------------------------------+
- | 6-STEP DEVELOPED LENGTH SIZING PROCEDURE |
- +-------------------------------------------------------------------------+
- | |
- | [STEP 1] MEASURE DEVELOPED LENGTH |
- | Linear footage from meter to the most remote fixture. |
- | │ |
- | ▼ |
- | [STEP 2] CALCULATE TOTAL EQUIVALENT LENGTH |
- | Total Length = Developed Length × 1.50 (Fitting allowance) |
- | │ |
- | ▼ |
- | [STEP 3] IDENTIFY STATIC SUPPLY PRESSURE |
- | Minimum utility street pressure (or PRV setpoint). |
- | │ |
- | ▼ |
- | [STEP 4] DEDUCT CUMULATIVE FIXED PRESSURE LOSSES |
- | • Elevation Loss = Vertical Rise (ft) × 0.433 psi/ft |
- | • Water Meter Loss (from manufacturer chart: 3–8 psi) |
- | • Backflow Assembly Loss (RPZ = 8–12 psi; DCVA = 5–7 psi) |
- | • Water Treatment / Filter Loss (3–5 psi) |
- | • Minimum Fixture Residual Pressure (8–25 psi) |
- | │ |
- | ▼ |
- | [STEP 5] COMPUTE AVAILABLE FRICTION LOSS PER 100 FEET (ΔP₁₀₀) |
- | ΔP₁₀₀ = [Available Friction Loss ÷ Total Equiv Length] × 100 |
- | │ |
- | ▼ |
- | [STEP 6] SELECT PIPE DIAMETER FROM FRICTION LOSS CHARTS |
- | Verify velocity limits (≤ 8.0 fps cold, ≤ 5.0 fps hot). |
- | |
- +-------------------------------------------------------------------------+
- Detailed Mathematical Formulas
1. Elevation Pressure Loss / Gain:
Water exerts a downward hydrostatic head pressure of 0.433 psi per vertical foot of rise (conversely, 1.0 psi = 2.31 feet of water column 1.0\text{ psi} = 2.31\text{ feet of water column} 1.0 psi = 2.31 feet of water column ): Δ P elevation = Vertical Height (ft) × 0.433 psi/ft \Delta P_{\text{elevation}} = \text{Vertical Height (ft)} \times 0.433\text{ psi/ft} Δ P elevation = Vertical Height (ft) × 0.433 psi/ft
(Note: If a fixture is located below the meter level, elevation adds +0.433 psi/ft to available pressure).
2. Total Allowable Friction Pressure Drop ( P friction P_{\text{friction}} P friction ): P friction = P static − ( Δ P elevation + P meter + P backflow + P filter + P residual ) P_{\text{friction}} = P_{\text{static}} - \left(\Delta P_{\text{elevation}} + P_{\text{meter}} + P_{\text{backflow}} + P_{\text{filter}} + P_{\text{residual}}\right) P friction = P static − ( Δ P elevation + P meter + P backflow + P filter + P residual )
3. Allowable Friction Loss per 100 Feet ( Δ P 100 \Delta P_{100} Δ P 100 ): Δ P 100 = ( P friction Total Equivalent Developed Length (ft) ) × 100 \Delta P_{100} = \left( \frac{P_{\text{friction}}}{\text{Total Equivalent Developed Length (ft)}} \right) \times 100 Δ P 100 = ( Total Equivalent Developed Length (ft) P friction ) × 100
Flow Velocity Limitations & Erosion-Corrosion Physics
Excessive water velocity generates severe turbulence, hydraulic noise, joint stress, and erosion-corrosion (the mechanical stripping of the protective cuprous oxide film inside copper piping, causing catastrophic pinhole leaks). Velocity Equation: V = 0.408 × Q d 2 \text{Velocity Equation: } V = \frac{0.408 \times Q}{d^2} Velocity Equation: V = d 2 0.408 × Q
Where V = Flow Velocity (feet per second, fps) V = \text{Flow Velocity (feet per second, fps)} V = Flow Velocity (feet per second, fps) , Q = Flow Rate (GPM) Q = \text{Flow Rate (GPM)} Q = Flow Rate (GPM) , and d = Inside Pipe Diameter (inches) d = \text{Inside Pipe Diameter (inches)} d = Inside Pipe Diameter (inches) .
- Piping Service Maximum Permissible Velocity Engineering Rationale & Code Limit
- Cold Water Distribution 8.0 feet per second (fps) Prevents hydraulic cavitation, noise, and fitting erosion
Hot Water Distribution ( ≤ 140 ∘ F \le 140^\circ\text{F} ≤ 14 0 ∘ F ) 5.0 feet per second (fps) High water temperature accelerates chemical/cavitation erosion in copper
Hot Water Recirculation Loops 4.0–5.0 feet per second (fps) Continuous flow accelerates localized erosion at 90° elbows and tees
Exam Key Point: Hot water velocity is strictly restricted to 5.0 fps (compared to 8.0 fps for cold water) because heated water increases dissolved oxygen activity, softens the inner copper oxide patina, and accelerates cavitation wear.
Step-by-Step Worked Calculation Example
Project Scenario:
A two-story commercial medical office building in Charlotte, NC has the following specifications:
Fixtures: 6 Public Flushometer Water Closets (5.0 WSFU ea), 6 Public Lavatories (1.0 WSFU ea), 2 Breakroom Sinks (1.5 WSFU ea), 1 Service Sink (2.5 WSFU ea), 2 Exterior Hose Bibbs (first = 2.5, second = 1.0 WSFU).
Supply Data: Municipal street main static pressure = 75 psi .
Distance: Developed length from water meter to the highest, most remote second-floor flushometer = 140 feet .
Elevation: Highest fixture outlet is 22 feet above the water meter.
Appurtenances: 1-1/2" disc water meter (pressure drop at peak flow = 4.0 psi ); RPZ backflow preventer (loss = 9.5 psi ); water softener (loss = 3.5 psi ).
Piping Material: Type L Copper (Fairly Smooth Pipe).
Required Residual Pressure: Second-floor flushometer valve requires 15.0 psi residual operating pressure.
Step-by-Step Engineering Solution:
- Step 1: Calculate Total Building WSFU
- Water Closets: 6 × 5.0 = 30.0 WSFU 6 \times 5.0 = 30.0\text{ WSFU} 6 × 5.0 = 30.0 WSFU
- Lavatories: 6 × 1.0 = 6.0 WSFU 6 \times 1.0 = 6.0\text{ WSFU} 6 × 1.0 = 6.0 WSFU
- Breakroom Sinks: 2 × 1.5 = 3.0 WSFU 2 \times 1.5 = 3.0\text{ WSFU} 2 × 1.5 = 3.0 WSFU
- Service Sink: 1 × 2.5 = 2.5 WSFU 1 \times 2.5 = 2.5\text{ WSFU} 1 × 2.5 = 2.5 WSFU
- Hose Bibbs: 2.5 + 1.0 = 3.5 WSFU 2.5 + 1.0 = 3.5\text{ WSFU} 2.5 + 1.0 = 3.5 WSFU
Total Building WSFU = 30.0 + 6.0 + 3.0 + 2.5 + 3.5 = 45.0 WSFU 30.0 + 6.0 + 3.0 + 2.5 + 3.5 = \mathbf{45.0\text{ WSFU}} 30.0 + 6.0 + 3.0 + 2.5 + 3.5 = 45.0 WSFU
Step 2: Determine Peak Demand (GPM)
Consult Hunter's Curve 1 (Flushometer System) for 45.0 WSFU 45.0\text{ WSFU} 45.0 WSFU .
At 45 WSFU, Curve 1 yields: Peak Demand = 48.0 GPM .
Step 3: Calculate Total Equivalent Developed Length Total Equivalent Length = 140 ft developed length × 1.50 = 210 feet \text{Total Equivalent Length} = 140\text{ ft developed length} \times 1.50 = \mathbf{210\text{ feet}} Total Equivalent Length = 140 ft developed length × 1.50 = 210 feet
Step 4: Calculate Cumulative Fixed Pressure Losses
Elevation Loss: 22 ft × 0.433 psi/ft = 9.53 psi 22\text{ ft} \times 0.433\text{ psi/ft} = 9.53\text{ psi} 22 ft × 0.433 psi/ft = 9.53 psi
- Water Meter Drop: 4.00 psi 4.00\text{ psi} 4.00 psi
- RPZ Backflow Assembly Drop: 9.50 psi 9.50\text{ psi} 9.50 psi
- Water Softener Drop: 3.50 psi 3.50\text{ psi} 3.50 psi
- Minimum Required Residual Pressure: 15.00 psi 15.00\text{ psi} 15.00 psi
Total Fixed Deductions: 9.53 + 4.00 + 9.50 + 3.50 + 15.00 = 41.53 psi 9.53 + 4.00 + 9.50 + 3.50 + 15.00 = \mathbf{41.53\text{ psi}} 9.53 + 4.00 + 9.50 + 3.50 + 15.00 = 41.53 psi
Step 5: Compute Available Friction Loss per 100 Feet ( Δ P 100 \Delta P_{100} Δ P 100 ) P friction = 75.0 psi (static) − 41.53 psi (losses) = 33.47 psi P_{\text{friction}} = 75.0\text{ psi (static)} - 41.53\text{ psi (losses)} = 33.47\text{ psi} P friction = 75.0 psi (static) − 41.53 psi (losses) = 33.47 psi Δ P 100 = ( 33.47 psi 210 ft ) × 100 = 15.94 psi per 100 ft \Delta P_{100} = \left( \frac{33.47\text{ psi}}{210\text{ ft}} \right) \times 100 = \mathbf{15.94\text{ psi per 100 ft}} Δ P 100 = ( 210 ft 33.47 psi ) × 100 = 15.94 psi per 100 ft
Step 6: Select Pipe Size from Friction Loss Tables
Design Flow: 48.0 GPM .
Allowable Loss Limit: ≤ 15.94 psi/100 ft \le 15.94\text{ psi/100 ft} ≤ 15.94 psi/100 ft .
Cold Velocity Limit: ≤ 8.0 fps \le 8.0\text{ fps} ≤ 8.0 fps .
Evaluating Type L Copper Options:
1-1/4" Type L Copper at 48 GPM: Velocity ≈ 11.1 fps \approx 11.1\text{ fps} ≈ 11.1 fps (❌ Exceeds 8.0 fps limit; friction loss ≈ 28.0 psi/100 ft \approx 28.0\text{ psi/100 ft} ≈ 28.0 psi/100 ft , exceeds allowable 15.94).
1-1/2" Type L Copper at 48 GPM: Velocity ≈ 7.9 fps \approx 7.9\text{ fps} ≈ 7.9 fps (✅ Within 8.0 fps limit); Friction loss ≈ 9.8 psi/100 ft \approx 9.8\text{ psi/100 ft} ≈ 9.8 psi/100 ft (✅ Well below allowable 15.94 psi/100 ft).
2" Type L Copper at 48 GPM: Velocity ≈ 4.6 fps \approx 4.6\text{ fps} ≈ 4.6 fps ; Friction loss ≈ 2.7 psi/100 ft \approx 2.7\text{ psi/100 ft} ≈ 2.7 psi/100 ft .
Engineered Sizing Selection: 1-1/2" Type L Copper main water service and building distribution trunk.
Exam Traps & Pro-Tips
Warning
Common Exam Pitfall #1 — Adding Cold and Hot WSFU Directly: Never add cold WSFU and hot WSFU together to size the main building supply line. Always use the Total WSFU column from Table E103.3(2). Cold and hot branches are sized using their respective sub-columns.
Important
Exam Pro-Tip #2 — 0.433 PSI/FT Elevation Rule: Elevation loss is always 0.433 psi per foot of rise ( 22 ft × 0.433 = 9.53 psi 22\text{ ft} \times 0.433 = 9.53\text{ psi} 22 ft × 0.433 = 9.53 psi ). If an exam problem places a fixture in a basement below the supply meter, you must add 0.433 psi/ft to available pressure.
Tip
Exam Pro-Tip #3 — 50% Fitting Allowance: When sizing piping using the equivalent length method, the standard code factor for fittings is 1.50 (150% of linear developed length), unless exact fitting equivalent tables are specified.