Study guide

12.7 Process Control Mathematics: Loading, Efficiency, Removal & Solids

North Carolina Water/Wastewater Operator Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: North Carolina Regulatory Framework, Certification & Classification

1.1 Dual Regulatory Structure: WTFOCB, WPCSOCC & NC DEQ 1.2 Drinking Water Certification Grades, Eligibility & the Apprentice Pathway 1.3 Examinations, Fees, Renewal, Continuing Education & Discipline 1.4 Classifying Drinking Water Facilities: Rating Values, Classes & Required Operators 1.5 Classifying Water Pollution Control Systems Under 15A NCAC 08G .0300 1.6 Wastewater Certification Types, Experience Ladders, OIT & Reciprocity

2 Chapter 2: Operator in Responsible Charge, Oversight & Regulatory Reporting

2.1 Designating the ORC and Back-up ORC: Forms, Deadlines & Legal Duties 2.2 Mandatory Visitation Frequencies & Facility Oversight 2.3 Operational Logs, Records Retention & Compliance Reporting 2.4 Sanitary Sewer Overflows: Reporting, Press Releases & Public Notice 2.5 The Federal Drinking Water Rule Framework Operators Are Tested On

3 Chapter 3: Drinking Water Treatment: Source Water Through Filtration

3.1 Source Water Quality, Raw Water Intake & Rapid Mixing 3.2 Coagulation Chemistry, Flocculation & Sedimentation Basins 3.3 Granular Media Filtration, Head Loss & Backwash Protocols 3.4 Taste and Odor Control, Powdered Activated Carbon & Algae Management

4 Chapter 4: Disinfection, Chemical Conditioning & Advanced Water Treatment

4.1 Chlorination Chemistry, Breakpoint Chlorination & CT Disinfection Inactivation 4.2 Disinfection Byproducts (TTHM & HAA5), Stage 1/2 DBPR & Enhanced Coagulation 4.3 Corrosion Control, Lead & Copper Rule Revisions, Fluoridation & Groundwater Treatment 4.4 Iron and Manganese Control: Oxidation, Greensand & Sequestration 4.5 Softening, Ion Exchange & Membrane Treatment 4.6 Water Plant Residuals, Backwash Recovery & Waste Disposal

5 Chapter 5: Groundwater Sources, Wells & Small Water Systems

5.1 Well Hydrology, Aquifers & North Carolina Well Construction Standards 5.2 Well Pumps, Wellhead Equipment & Source Protection 5.3 Small Water System Operations, Administration & Plant Recordkeeping

6 Chapter 6: Water Distribution Systems, Storage & Cross-Connection Control

6.1 Water Distribution Hydraulics, Storage Facilities & Water Quality Maintenance 6.2 Water Use, Demand Patterns & Distribution System Design 6.3 Pipe Materials, Main Installation, Service Connections & Meters 6.4 Fire Hydrants, Valve Operation & Distribution Operational Practices 6.5 Pump Hydraulics, Valve Operation & Cross-Connection Control / Backflow Prevention 6.6 System Mapping, Records & Information Management 6.7 Utility Security, Emergency Response & Boil Water Advisories

7 Chapter 7: Instrumentation, Electrical Fundamentals, Maintenance & Microbiological Monitoring

7.1 Instrumentation, Electrical Fundamentals & SCADA 7.2 Preventive Maintenance, Pumps, Motors & Mechanical Equipment 7.3 Bacteriology, Sample Siting Plans & RTCR Compliance Sampling

8 Chapter 8: Biological Wastewater Treatment & Secondary Processes

8.1 Wastewater Characterization, Preliminary Screening & Primary Clarification 8.2 Wastewater Lagoons, Stabilization Ponds & Operational Control 8.3 Constructed Wetlands & Natural Treatment Systems 8.4 Septic Tanks, Media Filters, Aerobic Treatment Units & Grease Interceptors 8.5 Attached Growth Systems: Trickling Filters, RBCs & Fixed-Film Processes 8.6 Activated Sludge Microbiology, Aeration Basins & Secondary Clarifiers 8.7 Operational Process Control: F/M Ratio, MCRT / Sludge Age & SVI

9 Chapter 9: Nutrient Removal, Solids Handling & Effluent Management

9.1 Biological Nutrient Removal (BNR) in NC Nutrient-Sensitive Waters (NSW) 9.2 Sludge Stabilization, Aerobic/Anaerobic Digestion & Biosolids Management 9.3 Digester Gas Systems, Heating, Mixing & Explosion Safety 9.4 Composting, Thermal Drying & Alternative Solids Disposal 9.5 Odor Sources, Measurement & Control Technologies 9.6 Tertiary Filtration, Reclaimed Water & Reuse Under 15A NCAC 02U 9.7 Effluent Disinfection, Dechlorination & NPDES Permit Compliance

10 Chapter 10: Wastewater Collection Systems, Lift Stations & Field Operations

10.1 Wastewater Collection System Design, Lift Stations & Inflow and Infiltration (I/I) 10.2 Manholes, Service Taps, Laterals & Sewer Construction Practice 10.3 Sewer Cleaning, Root Control & Preventive Maintenance Programs 10.4 Collection System Inspection & Acceptance Testing 10.5 Job-Site Pre-Planning, Traffic Control & Field Work Safety

11 Chapter 11: Industrial Pretreatment & Physical/Chemical Treatment

11.1 Industrial Pretreatment Programs & Protecting the POTW 11.2 Physical/Chemical Treatment Processes for Industrial Wastewater 11.3 Groundwater Remediation Systems, Flow Equalization & Flow Measurement

12 Chapter 12: Laboratory, Safety, Utility Management & Applied Mathematics

12.1 Laboratory Analytical Methods, Sampling Procedures & QA/QC 12.2 Chemical Safety, Gaseous Chlorine Handling & Hazard Communication 12.3 Permit-Required Confined Space Entry & Excavation / Trenching Safety 12.4 Electrical Safety, Lockout/Tagout & Machine Guarding 12.5 Biological Hazards, PPE, Heat Stress & Personal Hygiene 12.6 Applied Water & Wastewater Mathematics & Process Calculations 12.7 Process Control Mathematics: Loading, Efficiency, Removal & Solids 12.8 Hydraulics, Pressure & Unit Conversion Mathematics 12.9 Utility Management: Personnel, Budgeting, Public Relations & Plant Security

12.7 Process Control Mathematics: Loading, Efficiency, Removal & Solids

Key Takeaways Explain This Topic AI

Removal efficiency equals (influent minus effluent) divided by influent, times 100, and is applied to BOD, TSS, and any other parameter measured on both sides of a process.

Organic loading rate equals pounds of BOD per day divided by the treatment volume, expressed per 1,000 cubic feet for fixed film or per acre-foot for lagoons.

Solids loading rate on a secondary clarifier uses the combined influent and return activated sludge flow times the MLSS concentration times 8.34, divided by the clarifier surface area.

Percent volatile solids reduction in digestion uses the Van Kleeck relationship, which corrects for the fact that only volatile matter is destroyed while fixed solids remain.

Sludge pumping mass equals gallons pumped times 8.34 times percent solids expressed as a decimal, times specific gravity when it differs meaningfully from 1.0.

Last updated: September 2026

12.7 Process Control Mathematics: Loading, Efficiency, Removal & Solids

Every North Carolina needs-to-know document lists mathematics as a required subject, and the examinations provide a state formula sheet . Knowing which formula applies — and what each variable means — is the actual skill being tested.

1. Removal efficiency Percent Removal = Influent − Effluent Influent × 100 \text{Percent Removal} = \frac{\text{Influent} - \text{Effluent}}{\text{Influent}} \times 100 Percent Removal = Influent Influent − Effluent ​ × 100

Example. Influent BOD 240 mg/L, effluent BOD 12 mg/L:

(240 − 12) ÷ 240 × 100 = 95.0 percent removal

The same relationship works on mass (pounds per day), which is what you use when flows differ between the two sampling points. North Carolina secondary treatment permits typically require a minimum 85 percent removal of BOD and TSS in addition to the concentration limits.

2. Loading rates

  • Rate Formula Typical units
  • Hydraulic loading Flow ÷ surface area gpd/ft²
  • Organic loading (fixed film) lb BOD/day ÷ media volume lb BOD/day per 1,000 ft³
  • Organic loading (lagoon) lb BOD/day ÷ surface area lb BOD/day per acre
  • Solids loading (clarifier) lb solids/day ÷ surface area lb/day/ft²
  • Weir overflow rate Flow ÷ weir length gpd/linear ft
  • Filtration rate Flow ÷ filter area gpm/ft²
  • Backwash rate Backwash flow ÷ filter area gpm/ft²

Worked example — solids loading rate on a secondary clarifier. A 65-foot diameter clarifier receives 2.4 MGD of plant flow plus 1.2 MGD of RAS, with MLSS at 3,100 mg/L.

  • Area = 0.785 × 65² = 0.785 × 4,225 = 3,316.6 ft²
  • Solids applied = (2.4 + 1.2) MGD × 3,100 mg/L × 8.34 = 3.6 × 3,100 × 8.34 = 93,074 lb/day
  • SLR = 93,074 ÷ 3,316.6 = 28.1 lb/day/ft²

That sits at the upper end of the usual 20 to 30 lb/day/ft² design range — a number worth watching if the sludge blanket is rising.

3. Sludge mass and volume lbs of dry solids = gallons × 8.34 × % solids 100 × specific gravity \text{lbs of dry solids} = \text{gallons} \times 8.34 \times \frac{\%\text{ solids}}{100} \times \text{specific gravity} lbs of dry solids = gallons × 8.34 × 100 % solids ​ × specific gravity

Example. 12,000 gallons of primary sludge at 4.5 percent solids (specific gravity taken as 1.02):

12,000 × 8.34 × 0.045 × 1.02 = 4,593 lb of dry solids

Volume change with thickening uses the inverse relationship between concentration and volume: V 2 = V 1 × P 1 P 2 V_2 = V_1 \times \frac{P_1}{P_2} V 2 ​ = V 1 ​ × P 2 ​ P 1 ​ ​

Thickening 30,000 gallons of 1.0 percent WAS to 5.0 percent gives 30,000 × (1.0 ÷ 5.0) = 6,000 gallons — an 80 percent volume reduction.

4. Volatile solids reduction (the Van Kleeck formula)

Because digestion destroys volatile matter but leaves fixed solids behind, a simple before-and-after comparison of volatile percentages understates the destruction. The standard correction is: % VSR = ( V i n − V o u t ) V i n − ( V i n × V o u t ) × 100 \%\text{VSR} = \frac{(V_{in} - V_{out})}{V_{in} - (V_{in} \times V_{out})} \times 100 % VSR = V in ​ − ( V in ​ × V o u t ​ ) ( V in ​ − V o u t ​ ) ​ × 100

where V is the volatile fraction expressed as a decimal .

Example. Feed sludge is 72 percent volatile (0.72); digested sludge is 52 percent volatile (0.52):

  • Numerator: 0.72 − 0.52 = 0.20
  • Denominator: 0.72 − (0.72 × 0.52) = 0.72 − 0.3744 = 0.3456
  • %VSR = 0.20 ÷ 0.3456 × 100 = 57.9 percent

That comfortably exceeds the 38 percent minimum used for the volatile solids reduction option under the federal vector attraction reduction requirements.

5. Blending, dilution, and chemical strength

The blending (mixture) equation: ( V 1 × C 1 ) + ( V 2 × C 2 ) = ( V 1 + V 2 ) × C m i x (V_1 \times C_1) + (V_2 \times C_2) = (V_1 + V_2) \times C_{mix} ( V 1 ​ × C 1 ​ ) + ( V 2 ​ × C 2 ​ ) = ( V 1 ​ + V 2 ​ ) × C mi x ​

Example. 4,000 gallons of 12.5 percent hypochlorite is blended with 1,000 gallons of water:

(4,000 × 12.5) + (1,000 × 0) = 5,000 × C → 50,000 = 5,000C → C = 10.0 percent

Chemical usage tracking. Pounds of chemical used per day divided by pounds of a target parameter removed per day gives a chemical efficiency figure that is far more useful for budgeting and troubleshooting than raw consumption. A rising alum-per-pound-of-turbidity figure means the water changed or the feed system is losing accuracy.

6. Detention time and hydraulic checks Detention time (hours) = Volume (gallons) × 24 Flow (gpd) \text{Detention time (hours)} = \frac{\text{Volume (gallons)} \times 24}{\text{Flow (gpd)}} Detention time (hours) = Flow (gpd) Volume (gallons) × 24 ​

Use it to sanity-check process problems: if a clarifier's detention time has fallen from 2.4 hours to 1.1 hours because the plant is passing wet weather flow, the solids carryover is hydraulic, not biological, and no amount of wasting adjustment will fix it.

7. Working an exam math problem

Write down what is asked , with units.

List the given values , converting to the units the formula expects — MGD, mg/L, feet, and gallons are the usual offenders.

Select the formula from the state formula sheet , and confirm the variables mean what you think.

Solve stepwise , carrying units through the arithmetic.

Sanity-check the answer : is an F/M of 12 plausible? Is a detention time of 0.02 hours plausible? A wrong unit conversion almost always produces an answer that is off by a factor of 10, 8.34, 1,440, or 7.48 — learn to recognize those fingerprints.

Note

Common conversions worth memorizing: 8.34 lb/gal; 7.48 gal/ft³; 62.4 lb/ft³; 1,440 min/day; 694.4 gpm per MGD; 1.547 cfs per MGD; 43,560 ft² per acre; 325,851 gallons per acre-foot; 2.31 ft of head per psi; 0.433 psi per foot of head.