Study guide

6.2 Water Use, Demand Patterns & Distribution System Design

North Carolina Water/Wastewater Operator Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: North Carolina Regulatory Framework, Certification & Classification

1.1 Dual Regulatory Structure: WTFOCB, WPCSOCC & NC DEQ 1.2 Drinking Water Certification Grades, Eligibility & the Apprentice Pathway 1.3 Examinations, Fees, Renewal, Continuing Education & Discipline 1.4 Classifying Drinking Water Facilities: Rating Values, Classes & Required Operators 1.5 Classifying Water Pollution Control Systems Under 15A NCAC 08G .0300 1.6 Wastewater Certification Types, Experience Ladders, OIT & Reciprocity

2 Chapter 2: Operator in Responsible Charge, Oversight & Regulatory Reporting

2.1 Designating the ORC and Back-up ORC: Forms, Deadlines & Legal Duties 2.2 Mandatory Visitation Frequencies & Facility Oversight 2.3 Operational Logs, Records Retention & Compliance Reporting 2.4 Sanitary Sewer Overflows: Reporting, Press Releases & Public Notice 2.5 The Federal Drinking Water Rule Framework Operators Are Tested On

3 Chapter 3: Drinking Water Treatment: Source Water Through Filtration

3.1 Source Water Quality, Raw Water Intake & Rapid Mixing 3.2 Coagulation Chemistry, Flocculation & Sedimentation Basins 3.3 Granular Media Filtration, Head Loss & Backwash Protocols 3.4 Taste and Odor Control, Powdered Activated Carbon & Algae Management

4 Chapter 4: Disinfection, Chemical Conditioning & Advanced Water Treatment

4.1 Chlorination Chemistry, Breakpoint Chlorination & CT Disinfection Inactivation 4.2 Disinfection Byproducts (TTHM & HAA5), Stage 1/2 DBPR & Enhanced Coagulation 4.3 Corrosion Control, Lead & Copper Rule Revisions, Fluoridation & Groundwater Treatment 4.4 Iron and Manganese Control: Oxidation, Greensand & Sequestration 4.5 Softening, Ion Exchange & Membrane Treatment 4.6 Water Plant Residuals, Backwash Recovery & Waste Disposal

5 Chapter 5: Groundwater Sources, Wells & Small Water Systems

5.1 Well Hydrology, Aquifers & North Carolina Well Construction Standards 5.2 Well Pumps, Wellhead Equipment & Source Protection 5.3 Small Water System Operations, Administration & Plant Recordkeeping

6 Chapter 6: Water Distribution Systems, Storage & Cross-Connection Control

6.1 Water Distribution Hydraulics, Storage Facilities & Water Quality Maintenance 6.2 Water Use, Demand Patterns & Distribution System Design 6.3 Pipe Materials, Main Installation, Service Connections & Meters 6.4 Fire Hydrants, Valve Operation & Distribution Operational Practices 6.5 Pump Hydraulics, Valve Operation & Cross-Connection Control / Backflow Prevention 6.6 System Mapping, Records & Information Management 6.7 Utility Security, Emergency Response & Boil Water Advisories

7 Chapter 7: Instrumentation, Electrical Fundamentals, Maintenance & Microbiological Monitoring

7.1 Instrumentation, Electrical Fundamentals & SCADA 7.2 Preventive Maintenance, Pumps, Motors & Mechanical Equipment 7.3 Bacteriology, Sample Siting Plans & RTCR Compliance Sampling

8 Chapter 8: Biological Wastewater Treatment & Secondary Processes

8.1 Wastewater Characterization, Preliminary Screening & Primary Clarification 8.2 Wastewater Lagoons, Stabilization Ponds & Operational Control 8.3 Constructed Wetlands & Natural Treatment Systems 8.4 Septic Tanks, Media Filters, Aerobic Treatment Units & Grease Interceptors 8.5 Attached Growth Systems: Trickling Filters, RBCs & Fixed-Film Processes 8.6 Activated Sludge Microbiology, Aeration Basins & Secondary Clarifiers 8.7 Operational Process Control: F/M Ratio, MCRT / Sludge Age & SVI

9 Chapter 9: Nutrient Removal, Solids Handling & Effluent Management

9.1 Biological Nutrient Removal (BNR) in NC Nutrient-Sensitive Waters (NSW) 9.2 Sludge Stabilization, Aerobic/Anaerobic Digestion & Biosolids Management 9.3 Digester Gas Systems, Heating, Mixing & Explosion Safety 9.4 Composting, Thermal Drying & Alternative Solids Disposal 9.5 Odor Sources, Measurement & Control Technologies 9.6 Tertiary Filtration, Reclaimed Water & Reuse Under 15A NCAC 02U 9.7 Effluent Disinfection, Dechlorination & NPDES Permit Compliance

10 Chapter 10: Wastewater Collection Systems, Lift Stations & Field Operations

10.1 Wastewater Collection System Design, Lift Stations & Inflow and Infiltration (I/I) 10.2 Manholes, Service Taps, Laterals & Sewer Construction Practice 10.3 Sewer Cleaning, Root Control & Preventive Maintenance Programs 10.4 Collection System Inspection & Acceptance Testing 10.5 Job-Site Pre-Planning, Traffic Control & Field Work Safety

11 Chapter 11: Industrial Pretreatment & Physical/Chemical Treatment

11.1 Industrial Pretreatment Programs & Protecting the POTW 11.2 Physical/Chemical Treatment Processes for Industrial Wastewater 11.3 Groundwater Remediation Systems, Flow Equalization & Flow Measurement

12 Chapter 12: Laboratory, Safety, Utility Management & Applied Mathematics

12.1 Laboratory Analytical Methods, Sampling Procedures & QA/QC 12.2 Chemical Safety, Gaseous Chlorine Handling & Hazard Communication 12.3 Permit-Required Confined Space Entry & Excavation / Trenching Safety 12.4 Electrical Safety, Lockout/Tagout & Machine Guarding 12.5 Biological Hazards, PPE, Heat Stress & Personal Hygiene 12.6 Applied Water & Wastewater Mathematics & Process Calculations 12.7 Process Control Mathematics: Loading, Efficiency, Removal & Solids 12.8 Hydraulics, Pressure & Unit Conversion Mathematics 12.9 Utility Management: Personnel, Budgeting, Public Relations & Plant Security

6.2 Water Use, Demand Patterns & Distribution System Design

Key Takeaways Explain This Topic AI

Average day demand in North Carolina residential systems commonly runs 50 to 100 gallons per capita per day, and design flows are built by multiplying that average by peaking factors: roughly 1.5 to 2.0 for maximum day and 2.5 to 4.0 or more for peak hour.

Fire flow requirements are usually the largest single demand a small system must meet, and 15A NCAC 18C .0901 prohibits hydrants on mains smaller than six inches or on systems not designed to carry fire protection flows.

Under 15A NCAC 18C .0902, no more than 20 residences may connect to a two-inch main, a looped two-inch main may serve no more than 40, and a two-inch main may not exceed 1,000 feet in length.

Unaccounted-for water is the difference between water produced and water billed or otherwise accounted for; a water audit separates real losses such as leakage from apparent losses such as meter under-registration.

Pressure zones are created where elevation change exceeds roughly 100 to 150 feet, because a single zone spanning that range cannot hold every customer within an acceptable pressure band.

Last updated: September 2026

6.2 Water Use, Demand Patterns & Distribution System Design

The Distribution needs-to-know outline opens with Water Use and System Design for a reason: every hydraulic decision an operator makes — which tank to fill, which pump to run, where to flush — rests on understanding the demand pattern.

1. Categories of water use

  • Category Typical share Notes
  • Domestic / residential 40–60% Interior use is fairly steady year round; irrigation drives summer peaks
  • Commercial / institutional 10–30% Schools, hospitals, laundries, restaurants
  • Industrial 0–40% Highly site-specific; a single process user can dominate a small system
  • Public / unbilled authorized ~5% Flushing, firefighting, street cleaning, municipal buildings
  • Losses Variable Leakage, unauthorized use, meter error

Per capita demand. A common North Carolina planning figure is 50 to 100 gallons per capita per day (gpcd) for residential systems; systems with substantial commercial or industrial load run higher. The operational value of the number is that it lets you sanity-check production: a 4,000-person system producing 900,000 gpd is producing 225 gpcd and almost certainly has a major leak or an unmetered industrial user.

  • 2. Variations and peaking factors Peak hour demand ~2.5 - 4.0 x average day (higher in small systems)
  • Maximum day demand ~1.5 - 2.0 x average day
  • Average day demand 1.0
  • Minimum hour ~0.25 - 0.5 x average day

Time of day: morning and early evening peaks, minimum in the early morning hours.

Day of week and season: summer irrigation and tourism can double a coastal system's demand.

Smaller systems peak harder. With few customers there is no statistical smoothing, so a 200-connection system can see a peak-hour factor well above 4.

Design rule of thumb: the distribution system must deliver the larger of (a) maximum day demand plus fire flow, or (b) peak hour demand — while still holding at least 20 psi everywhere under 18C .0901.

3. Fire flow

Fire flow requirements come from the Insurance Services Office rating schedule and local fire code, and depend on building construction, occupancy, exposure, and area. Typical needed fire flows range from 500–1,000 gpm for two hours in single-family residential areas to 3,500 gpm or more for four hours in commercial or industrial areas.

North Carolina's rules constrain what may be built:

Fire hydrants shall not be installed on water mains of less than six inches diameter , or on mains or systems not designed to carry fire protection flows (18C .0901).

Systems not designed for fire flows must hold at least 30 psi throughout the system during peak flow — a higher routine standard than the 20 psi fire-flow floor, precisely because there is no fire-flow event to design around.

Adding a fire protection system to a distribution system changes its classification under 18D .0205(b), and therefore the grade of ORC it requires.

4. Main sizing constraints in 15A NCAC 18C

  • Requirement Rule
  • Minimum main size: 2-inch nominal .0901

Minimum pressure: 20 psi at all points at peak demand (fire flow) ; 30 psi at peak flow for non-fire-flow systems .0901

No more than 20 residences (or equivalent) on a 2-inch line unless looped or supplied from two connections .0902(a)

  • A looped 2-inch main serves no more than 40 residences ; a 2-inch main may not exceed 1,000 feet .0902(b)
  • Dead ends require a hydrant or adequately sized flush valve with above-ground discharge .0903

Cover: below the frost line or 30 inches , whichever is greater; 12 inches clearance from other utilities .0904

New mains tested for leakage per AWWA standards .0905

10 feet lateral separation from sewers (or 18 inches vertical with the water main above, in a separate trench) .0906

5. Pressure zones

Pressure at a point equals the elevation difference to the hydraulic grade line times 0.433 psi per foot. A 100-foot elevation span therefore produces a 43 psi spread across a single zone — which is why systems split into pressure zones roughly every 100 to 150 feet of elevation , joined by booster pump stations (to raise pressure going uphill) and pressure reducing valve stations (to drop it going downhill). Each zone normally has its own storage, so its tank sets the zone's hydraulic grade line.

6. Water loss accounting

Unaccounted-for water = water produced − (water billed + authorized unbilled use). A modern water audit separates:

Real losses: leakage on mains, services, and storage overflows. Reduced by leak detection surveys, pressure management, and main replacement.

Apparent losses: meter under-registration, data handling errors, unauthorized consumption. Reduced by meter testing and replacement, and by billing audits.

Night flow analysis is the operator's most powerful tool: isolate a district, read the master meter during minimum-hour demand, and compare with expected legitimate night use. Persistent high night flow is leakage until proven otherwise.

Note

Tie demand to water quality. Oversized mains and tanks built for a growth that never came are the leading cause of excessive water age , disinfectant residual loss, nitrification in chloraminated systems, and DBP formation in the far reaches of the system. Design and operation are the same problem viewed at different time scales.