Study guide

3.2 Inductors, Capacitors, and RC/RL Time Constants

ASTM NCATT Aircraft Electronics Technician AET

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: DC Electricity and Circuit Fundamentals

1.1 DC Basic Terms, Atomic Structure, and Charge 1.2 Ohm's Law and Electrical Power 1.3 Series and Parallel DC Circuits 1.4 Voltage Drop, Circuit Protection, and Aircraft Batteries 1.5 Basic Circuit Troubleshooting

2 Chapter 2: AC Electricity

2.1 AC Fundamentals and Sine Wave Metrics 2.2 Inductive Reactance and Inductance 2.3 Capacitive Reactance and Capacitance 2.4 Impedance, Resonance, Power Factor, and Three-Phase Systems

3 Chapter 3: Passive Components and Transformers

3.1 Resistors and Resistor Color Codes 3.2 Inductors, Capacitors, and RC/RL Time Constants 3.3 Transformers and Magnetic Circuits

4 Chapter 4: Semiconductor Devices and Active Circuits

4.1 Diodes, Rectifiers, and Zener Diodes 4.2 Transistors, Relays, and Switches 4.3 Filters, Oscillators, and Multivibrators 4.4 Limiter Circuits

5 Chapter 5: Digital Techniques and Logic Systems

5.1 Numbering Systems and Conversions 5.2 Logic Gates and Logic Families 5.3 Sequential Logic, Flip-Flops, Counters, and Displays

6 Chapter 6: Maintenance, Safety, and Documentation

6.1 Electrical Safety, PPE, First Aid, and Noise Exposure 6.2 ESD Control, FOD Prevention, and Hazmat 6.3 Use of Common Tools 6.4 Test Equipment Operation 6.5 Aviation Regulations, Publications, and Documentation

7 Chapter 7: Aircraft Fundamentals and Wiring Systems

7.1 Aircraft Wiring Harnesses and Conductors 7.2 Wiring Installation Practices, Safety Wire, and Corrosion 7.3 Wire Maintenance and Continuity Testing 7.4 Aircraft Structures, Aerodynamics, Flight Controls, and Ground Handling

3.2 Inductors, Capacitors, and RC/RL Time Constants

Key Takeaways Explain This Topic AI

Capacitors store electrical energy in an electrostatic field with series (1/CT = ∑ 1/Cn) and parallel (CT = ∑ Cn) combination rules opposite to resistors.

Inductors store energy in a magnetic field with series (LT = ∑ Ln) and parallel (1/LT = ∑ 1/Ln) combination rules matching resistors.

The RC time constant (τ = RC) and RL time constant (τ = L/R) define the rate of transient charge/discharge voltage and current changes in reactive circuits.

One time constant (τ) corresponds to a 63.2% change toward final value, and full steady state is reached after 5 time constants (99.3% charge/discharge).

An open capacitor loses plate continuity (no charge current); a shorted capacitor behaves like near-zero ohms and often trips protection.

Last updated: July 2026

Inductors, Capacitors, and RC/RL Time Constants

Reactive passive components—inductors and capacitors—store electrical energy temporarily rather than dissipating it as heat. Inductors store energy in magnetic fields, while capacitors store energy in electrostatic fields. Understanding reactive transient behaviors, combination rules, and time constants ( τ \tau τ ) is essential for analyzing aircraft power filters, radar pulse-forming networks, and digital bus termination networks.

  • Fundamentals of Capacitors and Inductors
  • Capacitance and Electrostatic Energy Storage

A capacitor consists of two conducting plates separated by an insulating dielectric material. When a DC voltage is applied across the plates, electric charge accumulates, creating an electrostatic field. Capacitance ( C C C ) measures the ability to store charge ( Q Q Q ) per unit of applied voltage ( V V V ): C = Q V C = \frac{Q}{V} C = V Q ​

Capacitance is measured in Farads ( F \text{F} F ), though avionics circuits typically utilize microfarads ( μ F = 10 − 6 F \mu\text{F} = 10^{-6}\text{ F} μ F = 1 0 − 6 F ), nanofarads ( nF = 10 − 9 F \text{nF} = 10^{-9}\text{ F} nF = 1 0 − 9 F ), or picofarads ( pF = 10 − 12 F \text{pF} = 10^{-12}\text{ F} pF = 1 0 − 12 F ). The physical capacitance depends on plate surface area ( A A A ), plate separation distance ( d d d ), and dielectric permittivity ( ϵ \epsilon ϵ ): C = ϵ ⋅ A d = ϵ r ⋅ ϵ 0 ⋅ A d C = \frac{\epsilon \cdot A}{d} = \frac{\epsilon_r \cdot \epsilon_0 \cdot A}{d} C = d ϵ ⋅ A ​ = d ϵ r ​ ⋅ ϵ 0 ​ ⋅ A ​

Energy stored in a charged capacitor's electrostatic field is given by: E C = 1 2 C V 2 E_C = \frac{1}{2} C V^2 E C ​ = 2 1 ​ C V 2

Inductance and Magnetic Energy Storage

An inductor consists of a conductive wire coil wrapped around a magnetic or air core. When current flows through the coil, a magnetic field is established. Inductance ( L L L ) is the property of a circuit that opposes any change in electric current by inducing a counter-electromotive force ( CEMF \text{CEMF} CEMF ) proportional to the rate of change of current: v L ( t ) = L ⋅ d i d t v_L(t) = L \cdot \frac{di}{dt} v L ​ ( t ) = L ⋅ d t d i ​

Inductance is measured in Henries ( H \text{H} H ), millihenries ( mH = 10 − 3 H \text{mH} = 10^{-3}\text{ H} mH = 1 0 − 3 H ), or microhenries ( μ H = 10 − 6 H \mu\text{H} = 10^{-6}\text{ H} μ H = 1 0 − 6 H ). Physical inductance depends on coil turns ( N N N ), core magnetic permeability ( μ \mu μ ), core cross-sectional area ( A A A ), and coil length ( l l l ): L = μ ⋅ N 2 ⋅ A l L = \frac{\mu \cdot N^2 \cdot A}{l} L = l μ ⋅ N 2 ⋅ A ​

Energy stored in an inductor's magnetic field is given by: E L = 1 2 L I 2 E_L = \frac{1}{2} L I^2 E L ​ = 2 1 ​ L I 2

Series and Parallel Combination Rules

Calculating total capacitance ( C T C_T C T ​ ) and total inductance ( L T L_T L T ​ ) requires applying rules that reflect their inverse physical relationships relative to resistance.

Combination Rule Matrix

Component Series Connection Parallel Connection

Resistors ( R R R ) R T = R 1 + R 2 + ⋯ + R n R_T = R_1 + R_2 + \dots + R_n R T ​ = R 1 ​ + R 2 ​ + ⋯ + R n ​ 1 R T = 1 R 1 + 1 R 2 + ⋯ + 1 R n \frac{1}{R_T} = \frac{1}{R_1} + \frac{1}{R_2} + \dots + \frac{1}{R_n} R T ​ 1 ​ = R 1 ​ 1 ​ + R 2 ​ 1 ​ + ⋯ + R n ​ 1 ​

Inductors ( L L L ) L T = L 1 + L 2 + ⋯ + L n L_T = L_1 + L_2 + \dots + L_n L T ​ = L 1 ​ + L 2 ​ + ⋯ + L n ​ 1 L T = 1 L 1 + 1 L 2 + ⋯ + 1 L n \frac{1}{L_T} = \frac{1}{L_1} + \frac{1}{L_2} + \dots + \frac{1}{L_n} L T ​ 1 ​ = L 1 ​ 1 ​ + L 2 ​ 1 ​ + ⋯ + L n ​ 1 ​

Capacitors ( C C C ) 1 C T = 1 C 1 + 1 C 2 + ⋯ + 1 C n \frac{1}{C_T} = \frac{1}{C_1} + \frac{1}{C_2} + \dots + \frac{1}{C_n} C T ​ 1 ​ = C 1 ​ 1 ​ + C 2 ​ 1 ​ + ⋯ + C n ​ 1 ​ C T = C 1 + C 2 + ⋯ + C n C_T = C_1 + C_2 + \dots + C_n C T ​ = C 1 ​ + C 2 ​ + ⋯ + C n ​

Mathematical Rationale

Capacitors in Parallel : Connecting capacitors in parallel combines their plate surface areas ( A total = A 1 + A 2 A_{\text{total}} = A_1 + A_2 A total ​ = A 1 ​ + A 2 ​ ), directly increasing total capacitance ( C T = C 1 + C 2 C_T = C_1 + C_2 C T ​ = C 1 ​ + C 2 ​ ).

Capacitors in Series : Connecting capacitors in series effectively increases dielectric thickness ( d total = d 1 + d 2 d_{\text{total}} = d_1 + d_2 d total ​ = d 1 ​ + d 2 ​ ), reducing total capacitance. For two series capacitors: C T = C 1 ⋅ C 2 C 1 + C 2 C_T = \frac{C_1 \cdot C_2}{C_1 + C_2} C T ​ = C 1 ​ + C 2 ​ C 1 ​ ⋅ C 2 ​ ​

Inductors in Series/Parallel : Assuming negligible mutual magnetic coupling, inductors behave identically to resistors because adding series turns increases total magnetic flux linkage.

RC and RL Transient Time Constants

When DC voltage is suddenly applied to or removed from a reactive circuit, current and voltage do not transition instantaneously; they undergo an exponential transient phase.

Time Constant Definitions

RC Time Constant ( τ \tau τ ) : The time required for capacitor voltage or current to change by 63.2% of its total initial-to-final voltage differential: τ = R ⋅ C ( Seconds = Ω × Farads ) \tau = R \cdot C \quad (\text{Seconds} = \Omega \times \text{Farads}) τ = R ⋅ C ( Seconds = Ω × Farads )

RL Time Constant ( τ \tau τ ) : The time required for inductor current to build up or decay by 63.2% of its maximum value: τ = L R ( Seconds = Henries Ω ) \tau = \frac{L}{R} \quad \left(\text{Seconds} = \frac{\text{Henries}}{\Omega}\right) τ = R L ​ ( Seconds = Ω Henries ​ )

Universal Charge / Discharge Curve Table

  • Elapsed Time ( τ \tau τ ) Charge Percentage (Rising Curve) Discharge Percentage (Falling Curve)
  • 1 τ 1\tau 1 τ 63.2% 36.8%
  • 2 τ 2\tau 2 τ 86.5% 13.5%
  • 3 τ 3\tau 3 τ 95.0% 5.0%
  • 4 τ 4\tau 4 τ 98.2% 1.8%
  • 5 τ 5\tau 5 τ 99.3% (Steady State) 0.7% (Zero State)
  • Exponential Voltage and Current Equations

Capacitor Voltage Charging : v C ( t ) = V source ( 1 − e − t / τ ) v_C(t) = V_{\text{source}} \left(1 - e^{-t/\tau}\right) v C ​ ( t ) = V source ​ ( 1 − e − t / τ )

Capacitor Voltage Discharging : v C ( t ) = V initial ⋅ e − t / τ v_C(t) = V_{\text{initial}} \cdot e^{-t/\tau} v C ​ ( t ) = V initial ​ ⋅ e − t / τ

Inductor Current Build-up : i L ( t ) = V source R ( 1 − e − t / τ ) i_L(t) = \frac{V_{\text{source}}}{R} \left(1 - e^{-t/\tau}\right) i L ​ ( t ) = R V source ​ ​ ( 1 − e − t / τ )

Inductor Current Decay : i L ( t ) = I initial ⋅ e − t / τ i_L(t) = I_{\text{initial}} \cdot e^{-t/\tau} i L ​ ( t ) = I initial ​ ⋅ e − t / τ

  • Worked Calculations and Avionics Applications
  • Example 1: RC Pulse Timing Circuit

An aircraft navigation pulse generator uses an RC timing network with R = 150 k Ω R = 150\text{ k}\Omega R = 150 k Ω and C = 4.7 μ F C = 4.7\ \mu\text{F} C = 4.7 μ F driven by a 28 VDC step voltage.

Calculate Time Constant ( τ \tau τ ) : τ = ( 150 × 10 3 Ω ) × ( 4.7 × 10 − 6 F ) = 0.705 seconds \tau = (150 \times 10^3\ \Omega) \times (4.7 \times 10^{-6}\text{ F}) = 0.705\text{ seconds} τ = ( 150 × 1 0 3 Ω ) × ( 4.7 × 1 0 − 6 F ) = 0.705 seconds

Capacitor Voltage after 1 τ 1\tau 1 τ : V C ( 1 τ ) = 28 V × 0.632 = 17.70 Volts V_C(1\tau) = 28\text{ V} \times 0.632 = 17.70\text{ Volts} V C ​ ( 1 τ ) = 28 V × 0.632 = 17.70 Volts

Time to Reach Full Steady-State Charge ( 5 τ 5\tau 5 τ ) : t steady = 5 × 0.705 s = 3.525 seconds t_{\text{steady}} = 5 \times 0.705\text{ s} = 3.525\text{ seconds} t steady ​ = 5 × 0.705 s = 3.525 seconds

Example 2: Inductive Solenoid Kickback

When an aircraft fuel shutoff solenoid ( L = 2.0 H , R = 40 Ω L = 2.0\text{ H}, R = 40\ \Omega L = 2.0 H , R = 40 Ω ) is disconnected from 28 VDC, the sudden collapse of its magnetic field ( d i / d t → − ∞ di/dt \to -\infty d i / d t → − ∞ ) induces a massive negative voltage spike ( CEMF = − L d i d t \text{CEMF} = -L \frac{di}{dt} CEMF = − L d t d i ​ ) reaching several hundred volts. This inductive kickback destroys control transistors unless suppressed by a parallel flyback diode wired across the solenoid coil.

Avionics Traps & Maintenance Warnings

Capacitor High-Voltage Shock Risk : High-capacitance filter capacitors inside weather radar transmitters can retain lethal DC voltages for hours after system shutdown. Technicians must verify capacitor discharge using an approved safety grounding stick before touching internal terminals.

Electrolytic ESR Degradation : Aged aluminum electrolytic filter capacitors exhibit increased Equivalent Series Resistance (ESR), causing high AC ripple voltage on DC power buses without blowing fuses.

Capacitor Fault Isolation (NCATT Standard)

Beyond ESR aging, the NCATT AET standard requires technicians to isolate capacitors for improper installation, open-plate, and shorted-plate faults using visual and non-visual methods.

Improperly Installed Capacitors

Polarized electrolytics installed with reversed polarity, wrong voltage ratings, or non-compliant mounting (leads stressed, wrong footprint) fail early and can vent or explode. Confirm polarity marks, working voltage (WVDC), and installation standards before applying power.

Open Capacitors

An open capacitor loses continuity to one plate. AC coupling or filter action stops; no charging current flows in that branch. Voltage applied to the circuit (or branch) appears across the open component. On an ohmmeter, an open capacitor does not show the brief charging kick toward a rising resistance—it stays open/OL.

Shorted Capacitors

A shorted capacitor occurs when conductive plates make physical contact. Capacitance disappears electrically; the device behaves like a near-zero-ohm conductor and often trips a fuse or circuit breaker. Ohmmeter readings remain near 0 Ω instead of climbing toward infinite as a healthy dielectric would.

  • Fault Physical Meaning Circuit Effect Ohmmeter Behavior
  • Open Continuity lost to a plate No capacitive current; voltage across open Stays OL / no charge kick
  • Shorted Plates contact each other Capacitive qualities gone; high current Near 0 Ω continuously

Improper install Wrong polarity/mounting Immediate or delayed catastrophic failure Visual + out-of-spec readings

Avionics Trap: Confusing electrolytic ESR rise (high ripple, fuse still intact) with a hard short (breaker trips) delays the correct replacement strategy.