Study guide

3.1 Resistors and Resistor Color Codes

ASTM NCATT Aircraft Electronics Technician AET

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: DC Electricity and Circuit Fundamentals

1.1 DC Basic Terms, Atomic Structure, and Charge 1.2 Ohm's Law and Electrical Power 1.3 Series and Parallel DC Circuits 1.4 Voltage Drop, Circuit Protection, and Aircraft Batteries 1.5 Basic Circuit Troubleshooting

2 Chapter 2: AC Electricity

2.1 AC Fundamentals and Sine Wave Metrics 2.2 Inductive Reactance and Inductance 2.3 Capacitive Reactance and Capacitance 2.4 Impedance, Resonance, Power Factor, and Three-Phase Systems

3 Chapter 3: Passive Components and Transformers

3.1 Resistors and Resistor Color Codes 3.2 Inductors, Capacitors, and RC/RL Time Constants 3.3 Transformers and Magnetic Circuits

4 Chapter 4: Semiconductor Devices and Active Circuits

4.1 Diodes, Rectifiers, and Zener Diodes 4.2 Transistors, Relays, and Switches 4.3 Filters, Oscillators, and Multivibrators 4.4 Limiter Circuits

5 Chapter 5: Digital Techniques and Logic Systems

5.1 Numbering Systems and Conversions 5.2 Logic Gates and Logic Families 5.3 Sequential Logic, Flip-Flops, Counters, and Displays

6 Chapter 6: Maintenance, Safety, and Documentation

6.1 Electrical Safety, PPE, First Aid, and Noise Exposure 6.2 ESD Control, FOD Prevention, and Hazmat 6.3 Use of Common Tools 6.4 Test Equipment Operation 6.5 Aviation Regulations, Publications, and Documentation

7 Chapter 7: Aircraft Fundamentals and Wiring Systems

7.1 Aircraft Wiring Harnesses and Conductors 7.2 Wiring Installation Practices, Safety Wire, and Corrosion 7.3 Wire Maintenance and Continuity Testing 7.4 Aircraft Structures, Aerodynamics, Flight Controls, and Ground Handling

3.1 Resistors and Resistor Color Codes

Key Takeaways Explain This Topic AI

4-band and 5-band color code schemes map colors Black (0) through White (9), with Gold (±5%) and Silver (±10%) indicating tolerance on standard carbon composition and metal film resistors.

Power dissipation rating (P = I²R = V²/R) dictates physical component size rather than resistance value; exceeding power limits causes thermal degradation and open-circuit failure.

Potentiometers act as 3-terminal variable voltage dividers, whereas rheostats act as 2-terminal variable current limiters in avionics control circuits.

Failure modes present as either an open circuit (infinite resistance, zero current) or short circuit (zero resistance, maximum current), with opens being the overwhelming failure mode for fixed composition resistors.

An open resistor can interrupt current with no visible damage; isolate one lead before ohmmeter checks to avoid parallel-path false lows.

Last updated: July 2026

Resistors and Resistor Color Codes

In aircraft electronic systems, passive components form the foundational building blocks of pulse-shaping networks, bias networks, signal attenuators, and power distribution systems. Among passive components, resistors are the most ubiquitous. A resistor is a two-terminal passive electrical element designed to introduce a specific, controlled amount of electrical resistance ( R R R ) into a circuit, thereby limiting current flow ( I I I ) or creating a voltage drop ( V V V ) in accordance with Ohm's law ( V = I × R V = I \times R V = I × R ).

Fundamentals of Fixed and Variable Resistors

Resistance is the physical property of a material to oppose the flow of free electrons. The resistance of a conductor depends on its physical dimensions and material resistivity ( ρ \rho ρ ): R = ρ ⋅ L A R = \frac{\rho \cdot L}{A} R = A ρ ⋅ L ​

Where L L L is the conductor length in meters, A A A is the cross-sectional area in square meters, and ρ \rho ρ is the material resistivity in ohm-meters ( Ω ⋅ m \Omega\cdot\text{m} Ω ⋅ m ). In avionics applications, resistors must maintain stable resistance values across severe environmental conditions, including ambient temperatures ranging from − 55 ∘ C -55^\circ\text{C} − 5 5 ∘ C to + 125 ∘ C +125^\circ\text{C} + 12 5 ∘ C , atmospheric pressure changes from sea level to 50,000 feet, and intense vibration.

Resistor Technologies in Avionics

Carbon Composition Resistors : Constructed from a mixture of powdered carbon and ceramic binder. Although inexpensive and robust against high-voltage surges, they exhibit relatively wide tolerances ( ± 5 % \pm 5\% ± 5% to ± 20 % \pm 20\% ± 20% ), high noise figures, and high positive temperature coefficients (PTC), causing resistance to drift noticeably with temperature changes.

Metal Film and Carbon Film Resistors : Manufactured by depositing a thin layer of resistive metal or carbon onto an insulating ceramic substrate. Metal film resistors provide high precision (tolerances of ± 0.1 % \pm 0.1\% ± 0.1% to ± 1 % \pm 1\% ± 1% ), low temperature coefficients, and low noise, making them ideal for sensitive avionics analog signal conditioning circuits.

Wirewound Resistors : Constructed by winding high-resistivity alloy wire (such as Nichrome) around a ceramic core. They excel in high-power dissipation applications (5 W to over 100 W), such as pitot tube heater current limiters and generator control unit (GCU) bleed loads. However, their spiral winding introduces significant parasitic inductance, making them unsuitable for high-frequency RF circuits.

Surface-Mount Device (SMD) Resistors : Compact ceramic chip resistors featuring planar thick-film or thin-film elements. Standard SMD packages (0603, 0805, 1206) dominate modern integrated avionics units (LRUs) due to minimal parasitic inductance and automated placement compatibility.

Potentiometers vs. Rheostats

Variable resistors allow manual or automatic adjustment of circuit resistance:

Potentiometer : A three-terminal device consisting of a resistive element and an adjustable sliding contact (wiper). Connected across a voltage source, it acts as an adjustable voltage divider. The voltage output at the wiper varies continuously from the minimum to maximum applied voltage: V out = V in ⋅ ( R wiper-to-ground R total ) V_{\text{out}} = V_{\text{in}} \cdot \left(\frac{R_{\text{wiper-to-ground}}}{R_{\text{total}}}\right) V out ​ = V in ​ ⋅ ( R total ​ R wiper-to-ground ​ ​ )

Potentiometers are used in flight deck audio volume controls, trim tab position feedback sensors, and flap indicator transmitters.

Rheostat : A two-terminal (or three-terminal with wiper tied to one end) variable resistor wired in series with a load to directly limit current. Rheostats must dissipate significant power because full load current flows through the resistive element. They are found in legacy cockpit floodlight dimmers and motor speed controls.

Standard 4-Band and 5-Band Color Code System

Through-hole resistors use color-coded bands printed around their cylindrical bodies to denote nominal resistance value, multiplier, and tolerance. Avionics technicians must rapidly and accurately decode both 4-band standard resistors and 5-band precision resistors.

Color Code Reference Table

  • Color 1st Digit 2nd Digit 3rd Digit (5-Band Only) Multiplier Tolerance
  • Black 0 0 0 10 0 = 1 10^0 = 1 1 0 0 = 1 —
  • Brown 1 1 1 10 1 = 10 10^1 = 10 1 0 1 = 10 ± 1 % \pm 1\% ± 1% (F)
  • Red 2 2 2 10 2 = 100 10^2 = 100 1 0 2 = 100 ± 2 % \pm 2\% ± 2% (G)
  • Orange 3 3 3 10 3 = 1 k Ω 10^3 = 1\text{ k}\Omega 1 0 3 = 1 k Ω —
  • Yellow 4 4 4 10 4 = 10 k Ω 10^4 = 10\text{ k}\Omega 1 0 4 = 10 k Ω —
  • Green 5 5 5 10 5 = 100 k Ω 10^5 = 100\text{ k}\Omega 1 0 5 = 100 k Ω ± 0.5 % \pm 0.5\% ± 0.5% (D)
  • Blue 6 6 6 10 6 = 1 M Ω 10^6 = 1\text{ M}\Omega 1 0 6 = 1 M Ω ± 0.25 % \pm 0.25\% ± 0.25% (C)
  • Violet 7 7 7 10 7 = 10 M Ω 10^7 = 10\text{ M}\Omega 1 0 7 = 10 M Ω ± 0.1 % \pm 0.1\% ± 0.1% (B)
  • Gray 8 8 8 10 8 = 100 M Ω 10^8 = 100\text{ M}\Omega 1 0 8 = 100 M Ω ± 0.05 % \pm 0.05\% ± 0.05% (A)
  • White 9 9 9 10 9 = 1 G Ω 10^9 = 1\text{ G}\Omega 1 0 9 = 1 G Ω —
  • Gold — — — 10 − 1 = 0.1 10^{-1} = 0.1 1 0 − 1 = 0.1 ± 5 % \pm 5\% ± 5% (J)
  • Silver — — — 10 − 2 = 0.01 10^{-2} = 0.01 1 0 − 2 = 0.01 ± 10 % \pm 10\% ± 10% (K)
  • None — — — — ± 20 % \pm 20\% ± 20%
  • Decoding Formulas

4-Band Decoding : R = ( Band 1 × 10 + Band 2 ) × 10 Band 3 ( ± Band 4 Tolerance ) R = (\text{Band}_1 \times 10 + \text{Band}_2) \times 10^{\text{Band}_3} \quad (\pm \text{Band}_4 \text{ Tolerance}) R = ( Band 1 ​ × 10 + Band 2 ​ ) × 1 0 Band 3 ​ ( ± Band 4 ​ Tolerance )

5-Band Precision Decoding : R = ( Band 1 × 100 + Band 2 × 10 + Band 3 ) × 10 Band 4 ( ± Band 5 Tolerance ) R = (\text{Band}_1 \times 100 + \text{Band}_2 \times 10 + \text{Band}_3) \times 10^{\text{Band}_4} \quad (\pm \text{Band}_5 \text{ Tolerance}) R = ( Band 1 ​ × 100 + Band 2 ​ × 10 + Band 3 ​ ) × 1 0 Band 4 ​ ( ± Band 5 ​ Tolerance )

Worked Calculation Examples

Example 1 (4-Band) : Determine nominal resistance and acceptable limit range for a resistor with color bands Yellow, Violet, Orange, Gold .

  • Band 1 (Yellow) = 4
  • Band 2 (Violet) = 7
  • Band 3 (Orange Multiplier) = 10 3 = 1 , 000 10^3 = 1,000 1 0 3 = 1 , 000
  • Band 4 (Gold Tolerance) = ± 5 % \pm 5\% ± 5%

Nominal value: 47 × 1 , 000 = 47 , 000 Ω = 47 k Ω 47 \times 1,000 = 47,000\ \Omega = 47\text{ k}\Omega 47 × 1 , 000 = 47 , 000 Ω = 47 k Ω .

Tolerance calculation: 47 , 000 × 0.05 = 2 , 350 Ω = 2.35 k Ω 47,000 \times 0.05 = 2,350\ \Omega = 2.35\text{ k}\Omega 47 , 000 × 0.05 = 2 , 350 Ω = 2.35 k Ω .

Acceptable range: 47 , 000 − 2 , 350 = 44 , 650 Ω ( 44.65 k Ω ) 47,000 - 2,350 = 44,650\ \Omega\ (44.65\text{ k}\Omega) 47 , 000 − 2 , 350 = 44 , 650 Ω ( 44.65 k Ω ) to 47 , 000 + 2 , 350 = 49 , 350 Ω ( 49.35 k Ω ) 47,000 + 2,350 = 49,350\ \Omega\ (49.35\text{ k}\Omega) 47 , 000 + 2 , 350 = 49 , 350 Ω ( 49.35 k Ω ) .

Example 2 (5-Band Precision) : Determine nominal resistance for a resistor with color bands Brown, Black, Black, Red, Brown .

  • Band 1 (Brown) = 1
  • Band 2 (Black) = 0
  • Band 3 (Black) = 0
  • Band 4 (Red Multiplier) = 10 2 = 100 10^2 = 100 1 0 2 = 100
  • Band 5 (Brown Tolerance) = ± 1 % \pm 1\% ± 1%

Nominal value: ( 100 ) × 100 = 10 , 000 Ω = 10.0 k Ω ± 1 % (100) \times 100 = 10,000\ \Omega = 10.0\text{ k}\Omega \pm 1\% ( 100 ) × 100 = 10 , 000 Ω = 10.0 k Ω ± 1% .

Power Rating and Physical Sizing

A resistor's power rating specifies the maximum electrical power it can dissipate as heat without suffering physical destruction or permanent resistance alteration. Power dissipation ( P P P ) is calculated using Watt's law combined with Ohm's law: P = I ⋅ V = I 2 ⋅ R = V 2 R P = I \cdot V = I^2 \cdot R = \frac{V^2}{R} P = I ⋅ V = I 2 ⋅ R = R V 2 ​

Critical Sizing Rules

Physical Dimensions vs. Resistance Value : Physical size is determined entirely by power rating, not resistance. A 10 Ω 10\ \Omega 10 Ω , 10 -watt 10\text{-watt} 10 -watt wirewound resistor is physically fifty times larger than a 10 M Ω 10\text{ M}\Omega 10 M Ω , 0.25 -watt 0.25\text{-watt} 0.25 -watt carbon film resistor.

Avionics Derating Standard : In aircraft design (such as MIL-STD-1553 bus terminators), resistors are operating at a maximum of 50% of their rated power (e.g., using a 0.5 W resistor for a 0.2 W actual load) to ensure thermal reliability across high ambient cockpit temperatures.

Worked Power Calculation

An avionics indicator lamp circuit applies 28 VDC across a current-limiting resistor of 560 Ω 560\ \Omega 560 Ω .

Actual power dissipated: P = V 2 R = 28 2 560 = 784 560 = 1.4 Watts P = \frac{V^2}{R} = \frac{28^2}{560} = \frac{784}{560} = 1.4\text{ Watts} P = R V 2 ​ = 560 2 8 2 ​ = 560 784 ​ = 1.4 Watts

Selection requirement: A standard 0.25 W or 0.5 W resistor would instantly overheat and open. An technician must select a resistor rated for at least 2.0 W or 3.0 W to satisfy derating guidelines.

Resistor Failure Symptoms and Avionics Troubleshooting

When performing bench tests or on-aircraft troubleshooting, resistors exhibit two principal failure modes:

Open Circuit Failure (Overwhelmingly Common) : Thermal overload, mechanical shock, or age causes the resistive film or wire element to fracture.

DMM Symptom : Infinite resistance ( OL \text{OL} OL or > 200 M Ω >200\text{ M}\Omega > 200 M Ω ).

Circuit Behavior : Current through the branch falls to zero ( I = 0 A I = 0\text{ A} I = 0 A ), and full supply voltage appears across the open resistor terminals ( V open = V source V_{\text{open}} = V_{\text{source}} V open ​ = V source ​ ).

Short Circuit Failure (Extremely Rare) : Metal migration or carbonized tracking across an overheated ceramic substrate creates a low-resistance path.

DMM Symptom : Near zero resistance ( R ≈ 0 Ω R \approx 0\ \Omega R ≈ 0 Ω ).

Circuit Behavior : Branch current increases dramatically, potentially tripping circuit breakers or blowing upstream fuses.

Resistance Value Drift : Overheated metal film resistors may drift above or below specified tolerance bands without opening completely.

Avionics Troubleshooting Traps

In-Circuit Parallel Path Fallacy : Never measure a resistor's resistance while it is connected in an un-energized circuit without isolating at least one leg. Parallel circuit paths formed by adjacent semiconductor junctions or transformer windings will shunt DMM test current, producing a false low resistance reading.

Resistor Fault Isolation (NCATT Standard)

Isolating a faulty resistor is a core NCATT AET skill. Use visual inspection first, then an ohmmeter with at least one lead lifted so parallel paths cannot shunt the reading.

Improperly Installed Resistors

Resistors installed backwards in polarity-sensitive packages, forced into wrong footprint pads, or mounted non-compliant to industry installation standards create intermittent opens, shorts to adjacent traces, and heat-related failures. Always verify part number, wattage rating, and mounting orientation against the wiring diagram or board silkscreen.

Open Resistors

An open resistor has an incomplete path for current between terminals. Current in that branch drops to zero. The full applied voltage appears across the open device. Critically, a resistor or fuse can open with no visible signs of damage —never assume a clean body means a good part.

Resistors of Incorrect Value

A resistor outside its specified tolerance band (wrong color-code reading, drifted metal-film value after overheating, or wrong replacement part) shifts bias points, LED current, and divider ratios. Confirm value with an ohmmeter against the schematic callout, including tolerance.

Shorted Resistors

A shorted resistor allows current to flow across a path that should have been resistive. On densely packed printed circuit boards, foreign conductive debris between adjacent traces commonly creates short-like behavior. Foreign Object Debris (FOD) bridging resistor pads is a frequent hangar-floor root cause.

  • Fault Mode Typical Symptom DMM Clue (power OFF, one lead lifted)
  • Open Branch current = 0; full supply across device Infinite / OL resistance
  • Incorrect value Wrong bias, dim lamps, off-spec timing Reading outside tolerance
  • Shorted Excess current; blown fuse/CB possible Near 0 Ω across terminals
  • Improper install Intermittent, heat, mechanical stress marks Visual non-compliance

Avionics Trap: Replacing a drifted resistor without checking for solder bridges or conductive FOD often brings the same short back after the next vibration cycle.