Study guide
11.4 Blocks, Beam Clamps, Softeners, and Related Gear
NCCCO Rigger Level I Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 About the NCCCO Rigger Level I Exam 1.2 Level I vs Level II Scope 1.3 Eligibility, Fees, and Recertification
2 Scope: Load Path and Characteristics
2.1 Identifying the Load Travel Path 2.2 Load Weight and Center of Gravity 2.3 Attachment Points and Lift Points
3 Scope: Hazards and Unsafe Practices
3.1 Special Handling Requirements 3.2 Pinch Points and Softeners 3.3 Load Stability, Shock Load, and Side Loading 3.4 Electrical Hazards, Body Positioning, and Hazard Communication
4 Technical Knowledge: ASME Standards
4.1 ASME B30.9 Slings and B30.10 Hooks 4.2 ASME B30.26 Hardware and B30.20 Below-the-Hook
5 Technical Knowledge: OSHA Regulations
5.1 OSHA 1910.184 and 1926.251 5.2 OSHA 1926.1401 Qualified Rigger 5.3 OSHA 1926.1431 Hoisting Personnel
6 Inspection: Foundations, Wire Rope, and Chain
6.1 Frequent vs Periodic Inspection 6.2 Wire Rope Sling Inspection and Removal Criteria 6.3 Chain Sling Inspection and Removal Criteria
7 Inspection: Synthetic and Specialty Slings
7.1 Synthetic Web Sling Inspection 7.2 Synthetic Round Sling Inspection 7.3 Metal Mesh and Synthetic Rope Sling Inspection
8 Inspection: Hooks, Hardware, and Below-the-Hook Devices
8.1 Hook Inspection (ASME B30.10) 8.2 Shackles, Eyebolts, and Hardware Inspection 8.3 Below-the-Hook Device Inspection
9 Execution: Sling Types and Identification
9.1 Chain and Wire Rope Sling Use 9.2 Synthetic Web and Round Sling Use 9.3 Sling Identification Tags and WLL
10 Execution: Hitches, Angles, and Capacity
10.1 Vertical, Choker, and Basket Hitches 10.2 Sling Angle Factors 10.3 Hitch Capacity Calculations 10.4 Edge Protection and D/d Ratio
11 Execution: Rigging Hardware in Use
11.1 Shackles and Hooks in Use 11.2 Eyebolts and Swivel Hoist Rings 11.3 Wire Rope Clips and Compression Hardware 11.4 Blocks, Beam Clamps, Softeners, and Related Gear
12 Execution: Below-the-Hook Devices, Tag Lines, and Knots
12.1 Below-the-Hook Lifting Devices 12.2 Tag Line Use and Load Control 12.3 Basic Knots for Riggers
13 Execution: Post-Lift Activities and Communication
13.1 Securing, Disconnecting, and Stowing Gear 13.3 Stop Authority and Lift Communication
14 Practical Exam Prep and Study Strategy
14.1 Level I Practical Exam Tasks 14.2 Study Strategy and Exam Day
11.4 Blocks, Beam Clamps, Softeners, and Related Gear
Key Takeaways Explain This Topic AI
A snatch/rigging block that turns a line about 180° can place roughly 2× line pull on the block hook, becket, or support—size all components for that load.
Beam clamps must be used within rated capacity and correct orientation on an adequate beam; they are not freestyle permanent building supports unless designed and approved for that service.
Softeners and padding protect slings and finished surfaces at edges; they complement—but do not replace—correct hitch capacity and edge-aware execution.
Master links, rings, swivels, and turnbuckles must stay within WLL with proper engagement, locking, and in-line loading as designed.
Dollies, skates, and rollers are for controlled horizontal moves on prepared paths—not improvised overhead lifting points.
Last updated: July 2026
11.4 Blocks, Beam Clamps, Softeners, and Related Gear
Quick Answer: Treat snatch blocks as force multipliers—the load on the block’s hook/becket can approach about 2× line pull in a simple reeve. Use beam clamps only within rated capacity and orientation . Protect slings with softeners/padding . Know Level I awareness roles of links, rings, swivels, turnbuckles, jacks, trolleys, and A-frames. Use dollies, skates, and rollers for controlled horizontal moves—not as improvised overhead lifting gear.
Execution hardware is more than shackles and eyebolts. Level I candidates must recognize how blocks change loads, how beam clamps attach to structure, why softeners prevent sling damage, and what miscellaneous gear is for—without turning every tool into a crane substitute.
Rigging Blocks (Snatch Blocks) and Line Reeving
A snatch block (rigging block with a side-opening or standard sheave block used in rigging) changes the direction of a line and can provide mechanical advantage depending on reeving.
Load on the block support
In a common simple case—line coming from a winch, through a block, and back—the tension in each part of the line is related to the pull, and the block support (hook, becket, or shackle holding the block) can see roughly the vector sum of the line tensions.
- Configuration concept Load on block support (approximate teaching model)
- Line turned ~180° with equal tension both sides About 2 × line pull on the block hook/becket
Smaller included angle between line parts Support load less than 2× but still often greater than single line pull
Mechanical advantage multi-part reeve Line pull reduced for a given load, but block and structural anchors must still be analyzed for true loads
Level I exam classic: If the line pull is 1,000 lb and the rope turns back through a block approximately 180°, expect on the order of 2,000 lb on the block’s attachment—before dynamic factors. Always size the block WLL , the shackle , and the anchor for that amplified load, not merely the winch gauge reading of line pull.
- Check before using a block Why
- Block WLL ≥ calculated support load Sheave/hook can be overloaded even when line pull “looks low”
- Sheave size compatible with rope diameter Too-small sheave damages rope (D/d issues)
- Rope reeved correctly in the groove Jumping the sheave under load is catastrophic
- Latch/side plate secured on snatch blocks Opening under load drops the rope
- Fair lead; no severe fleet angle abuse Side load on sheave flanges and pins
- Reeving awareness
Keep the rope in the groove ; do not run over flanges.
Avoid reverse bends and tight fleet angles when the plan allows better geometry.
Dynamic snatch (shock) multiplies forces—Level I still refuses shock loading as a normal technique.
Blocks used for load direction changes still need inspection : cracks, worn sheaves, damaged hooks, missing latches, and illegible ratings.
Beam Clamps
Beam clamps attach to a structural beam flange to create a temporary lifting point for a hoist or block— when the clamp and the beam are both adequate .
Use rule Level I meaning
Rated capacity Clamp WLL must meet or exceed the applied load (including any block multiplication and hoist capacity interaction)
Orientation Install on the flange as the manufacturer shows—right-side-up, correct jaw engagement, locking features engaged
Beam capacity The building beam must support the load; a 2-ton clamp on a light purlin does not create a 2-ton structure
Not a permanent support unless designed/approved as such Temporary lift point ≠ engineered building hanger for ongoing service without engineering approval
- No side load beyond design Many clamps are for loads hanging essentially vertical under the clamp
- Orientation and locking
Select clamp size for flange thickness and width range.
Seat jaws fully on the flange; tighten/lock per manufacturer (screw, cam, lock nut, safety pin as designed).
Confirm the hoist hook or shackle hangs in the clamp’s load point without prying the jaws open.
Never use a beam clamp upside down or on the wrong flange edge if the design forbids it.
Do not use a clamp as a sliding trolley unless it is specifically a trolley-rated device.
- Misuse Hazard
- Over-opening jaws beyond flange range Slip-off under load
- Loading at a large angle from vertical Jaw pry-out; reduced capacity
Using as permanent hanger for pipe/electrical without approval Structural and code issues; not a rigger freestyle decision
- Clamp on damaged/corroded flange Local flange failure
- Missing lock/safety pin Clamp walks open
- Softeners and Padding
Softeners (edge protectors, padding, corner protectors, wear pads, blocking) protect slings and load surfaces from cutting, abrasion, and crushing.
Situation Softener role
Sharp plate edges on synthetic web/round slings Prevent cutting—capacity tags do not authorize unprotected sharp edges
- Wire rope over corners Improve bend radius / reduce crushing and broken wires
- Finished surfaces Prevent marring while still controlling the load
- Chain over soft product Blocking to distribute pressure
Execution rules:
Softeners must stay in place as tension comes on—use designed protectors, not a single wrap of cardboard that falls out.
Softeners are not a substitute for adequate sling capacity or proper hitch selection.
After the lift, inspect slings where they contacted edges—softeners reduce but do not eliminate all damage risk if undersized or displaced.
Chapter themes on pinch points and edge protection (scope/hitches chapters) connect here: hardware selection includes how the sling meets the load.
Links, Rings, Swivels, Turnbuckles, and Related Connectors (Awareness)
Hardware Primary Level I use concept
Master links / oblongs Collect multi-leg sling eyes for a single hook connection; must be rated and sized for the load and number of legs
- Rings Similar gathering/connection role when rated for lifting
- Coupling links Join chain legs or attachments—grade-compatible, properly locked
- Swivels Allow rotation to relieve twist; must be rated; seized swivels can transmit torque into the load path
Turnbuckles Adjust length/tension in a guy or assembly within WLL ; keep threads adequately engaged; lock as required; avoid side load bending the body
Eye & eye / jaw & jaw ends Match the connection type; pins retained correctly
- Turnbuckle practice Judgment
- Adjust under no-load or controlled conditions per plan Normal
- Use to “stretch” capacity beyond WLL Forbidden
- Leave minimal thread engagement for extra take-up Dangerous—insufficient engagement
- Side-load a turnbuckle as a makeshift link at 90° Misuse unless specifically designed
- Jacks, Trolleys, A-Frames (Level I Awareness Depth)
These appear as support and movement tools around the lift, not always as the primary crane hook path.
Equipment Awareness points
Jacks (hydraulic/mechanical) Rated capacity, solid footing, crib/block as load is raised, never work under a load supported only by a jack without proper cribbing/blocking practices; watch for kick-out on slick surfaces
Trolleys (beam trolleys) Match beam flange; rated WLL; locks/brakes as designed; do not free-wheel loads into people or edges
A-frames / gantries (portable) Rated capacity; correct assembly pins; level/setup on firm ground; load centered; follow manufacturer span and height limits
Come-alongs / lever hoists / chainfalls (related) Rated gear only; correct hitch; no side load on the hoist body; do not use as a permanent hanger unless designed
Level I does not require you to design a gantry system, but you must refuse gear that is unmarked, incomplete, or used far outside its obvious orientation.
Dollies, Skates, and Rollers for Horizontal Moves
Not every move is a hoist. Horizontal relocation of machinery often uses:
- Device Concept
- Machinery rollers / skates Low-profile wheeled units under a load for rolling on a prepared surface
- Dollies Wheeled platforms or cradles sized for the load footprint
Roller bars / pipes (traditional) High risk if uncontrolled—modern practice prefers rated skates; if used under controlled procedures, keep hands clear and control travel
Air skates / specialized movers Follow manufacturer and site procedure
Execution rules for horizontal moves:
Know the load weight and keep each skate within capacity (including uneven CG).
Prepare the path —grade, floor strength, obstacles, drop-offs.
Use push/pull control —tag lines, come-alongs, or powered movers as planned—not uncontrolled gravity on a slope.
Keep body parts out of pinch and crush zones between load and walls.
Do not hang a load from a dolly or use rollers as an improvised overhead block.
Transition carefully when going from rollers to permanent mounts or onto a crane lift—secure the load before removing support.
- Horizontal-move hazard Mitigation
- Load runs away on slope Chocks, controlled winch, no free coasting
- Skate kicks out Adequate contact area; clean floor; centered loading
- Floor collapse Verify floor loading; use plates to spread load
- Tip-over of tall CG loads Keep CG low/controlled; brace; small incremental moves
- Putting the Hardware Kit Together
A typical Level I execution sequence might combine several of these items:
Beam clamp (oriented and locked) on an adequate beam.
Shackle and snatch block hung from the clamp— block support sized for ~2× line pull if applicable.
Softeners on the load corners under synthetic slings.
Master link gathering bridle legs into the crane hook bowl.
After vertical placement, skates for the final horizontal alignment under a controlled procedure.
At every interface, apply the same three tests: rated , oriented , compatible with the next piece in the load path.
Exam Focus
Remember the ~2× line pull teaching model for a block that turns the line approximately 180°. Beam clamps need capacity + correct orientation + adequate structure and are not automatic permanent hangers. Softeners protect slings at edges. Links, rings, swivels, and turnbuckles stay within WLL with proper engagement and alignment. Jacks, trolleys, and A-frames are rated setup gear. Dollies/skates/rollers move loads horizontally under control—they do not replace proper lifting hardware overhead.