Study guide
11.2 Eyebolts and Swivel Hoist Rings
NCCCO Rigger Level I Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 About the NCCCO Rigger Level I Exam 1.2 Level I vs Level II Scope 1.3 Eligibility, Fees, and Recertification
2 Scope: Load Path and Characteristics
2.1 Identifying the Load Travel Path 2.2 Load Weight and Center of Gravity 2.3 Attachment Points and Lift Points
3 Scope: Hazards and Unsafe Practices
3.1 Special Handling Requirements 3.2 Pinch Points and Softeners 3.3 Load Stability, Shock Load, and Side Loading 3.4 Electrical Hazards, Body Positioning, and Hazard Communication
4 Technical Knowledge: ASME Standards
4.1 ASME B30.9 Slings and B30.10 Hooks 4.2 ASME B30.26 Hardware and B30.20 Below-the-Hook
5 Technical Knowledge: OSHA Regulations
5.1 OSHA 1910.184 and 1926.251 5.2 OSHA 1926.1401 Qualified Rigger 5.3 OSHA 1926.1431 Hoisting Personnel
6 Inspection: Foundations, Wire Rope, and Chain
6.1 Frequent vs Periodic Inspection 6.2 Wire Rope Sling Inspection and Removal Criteria 6.3 Chain Sling Inspection and Removal Criteria
7 Inspection: Synthetic and Specialty Slings
7.1 Synthetic Web Sling Inspection 7.2 Synthetic Round Sling Inspection 7.3 Metal Mesh and Synthetic Rope Sling Inspection
8 Inspection: Hooks, Hardware, and Below-the-Hook Devices
8.1 Hook Inspection (ASME B30.10) 8.2 Shackles, Eyebolts, and Hardware Inspection 8.3 Below-the-Hook Device Inspection
9 Execution: Sling Types and Identification
9.1 Chain and Wire Rope Sling Use 9.2 Synthetic Web and Round Sling Use 9.3 Sling Identification Tags and WLL
10 Execution: Hitches, Angles, and Capacity
10.1 Vertical, Choker, and Basket Hitches 10.2 Sling Angle Factors 10.3 Hitch Capacity Calculations 10.4 Edge Protection and D/d Ratio
11 Execution: Rigging Hardware in Use
11.1 Shackles and Hooks in Use 11.2 Eyebolts and Swivel Hoist Rings 11.3 Wire Rope Clips and Compression Hardware 11.4 Blocks, Beam Clamps, Softeners, and Related Gear
12 Execution: Below-the-Hook Devices, Tag Lines, and Knots
12.1 Below-the-Hook Lifting Devices 12.2 Tag Line Use and Load Control 12.3 Basic Knots for Riggers
13 Execution: Post-Lift Activities and Communication
13.1 Securing, Disconnecting, and Stowing Gear 13.3 Stop Authority and Lift Communication
14 Practical Exam Prep and Study Strategy
14.1 Level I Practical Exam Tasks 14.2 Study Strategy and Exam Day
11.2 Eyebolts and Swivel Hoist Rings
Key Takeaways Explain This Topic AI
Shoulder eyebolts may accept angular loading only within manufacturer tables that reduce capacity as angle increases; non-shoulder (plain) eyebolts are for in-line loading only—never angular-load them.
Full thread engagement and proper shoulder seating are mandatory; incomplete engagement or a raised shoulder voids the rated load path.
Install to manufacturer seating/torque guidance; under- or over-torque and freestyle locking methods can destroy capacity assumptions.
Swivel hoist rings are preferred when the sling will pull multi-directionally or angles will change as the load rises or rotates.
Bent shanks, stretched eyes, and cracked transitions mean remove from service—do not re-rate a damaged eyebolt in the field.
Last updated: July 2026
11.2 Eyebolts and Swivel Hoist Rings
Quick Answer: Use shoulder (machinery) eyebolts only as rated—including reduced capacity for angular loading —and never angular-load non-shoulder (straight) eyebolts . Achieve full thread engagement and proper shoulder seating . For multi-directional or uncertain load angles, prefer swivel hoist rings rated for the applied direction.
Eyebolts and hoist rings turn a tapped hole or through-bolt pad into a lifting point. Level I candidates must know the difference between shoulder and non-shoulder designs, why angular loading is restricted, and when a swivel hoist ring is the safer hardware choice. Misused eyebolts are a classic failure mode because the shank sees bending that a pure tensile rating never contemplated.
Shoulder vs Non-Shoulder Eyebolts
Type Appearance / design cue Vertical (in-line) loading Angular loading
Shoulder eyebolt (often called machinery eyebolt with shoulder) Shoulder under the eye that seats against the load surface Rated for vertical use when fully engaged and seated Allowed only within manufacturer tables—capacity is reduced as angle increases
Non-shoulder / plain pattern / “straight” eyebolt No load-bearing shoulder under the eye In-line tensile use when fully engaged per rating Not for angular loading in standard Level I teaching
Why the shoulder matters
When load is perfectly in line with the shank, the eyebolt is primarily in tension . When the sling pulls at an angle, the shank experiences bending moment at the surface of the tapped part. The shoulder , when fully seated on a flat surface, helps the assembly resist that bending within the limits the manufacturer tested and published.
Without a shoulder—or with a shoulder that is not fully seated—angular load can bend the shank, crack the eye-to-shank transition, or strip threads at much lower loads than the vertical WLL suggests.
Angular loading capacity reduction (shoulder eyebolts)
Manufacturers publish reduction tables. Level I exam depth is the concept , not memorizing every brand’s chart:
- Loading condition (shoulder eyebolt, properly installed) Capacity concept
- Load in line with the shank (vertical relative to the bolt axis) Full rated WLL (if installation is correct)
- Load at an angle from the bolt axis Reduced WLL per manufacturer angular-loading chart
- Load approaching 45° and beyond (product-dependent) Often a large reduction; some angles are prohibited
- Load out of the plane of the eye Especially severe—follow manufacturer limits; often restricted
Exam habit: If a question states a shoulder eyebolt is loaded at an angle, the correct instinct is capacity is less than vertical WLL —consult the chart / lift plan. Do not apply full vertical rating to an angled pull.
Illustrative training-style pattern (always override with the actual manufacturer table for field use):
- Approximate angle from vertical (bolt axis) Typical training message
- 0° (in-line) Full rating (installation correct)
- ~45° Significant reduction (often on the order of half or per chart)
- Greater angles Further reduction or not permitted
Do not treat any single percentage as universal law on the job—charts differ—but do expect the exam to test that angular load reduces capacity .
Never Angular-Load Non-Shoulder (Machinery/Plain) Eyebolts
Non-shoulder eyebolts (plain pattern) are taught for in-line loading only in standard rigger curricula.
- Practice Level I judgment
- Non-shoulder eyebolt, load in line with shank, full engagement Acceptable if rated and installed for that use
- Non-shoulder eyebolt, sling angled so the eye is bent sideways Prohibited misuse
Non-shoulder eyebolt used as a “cheater” to pull at 45° because “it’s only a light load” Still wrong—bending failure risk is not fixed by “feeling light”
Replace non-shoulder with shoulder type or swivel hoist ring when angles are required Correct selection path
If the lift plan requires angular loading from a fixed pad:
- Use a shoulder eyebolt within its angular table, or
- Prefer a swivel hoist ring designed for multi-directional loading, or
Change the attachment geometry so the load is in line (engineered pad eye, lifting lug, etc.).
Level I does not redesign engineered lift points, but you must refuse an obvious non-shoulder angular pull that the provided configuration does not authorize.
- Full Thread Engagement, Seating, and Torque Concepts
- Thread engagement
Eyebolt strength depends on how the threads transfer load into the base material.
Installation check Pass concept
Full thread engagement Shank threads engage the full required depth in the tapped hole (or nut) per manufacturer—commonly taught as full engagement of the threaded length designed for that bolt
- Correct thread size / pitch Matches the tapped hole; no forced cross-threading
- Undamaged threads No stripped, crushed, or heavily corroded threads
Adequate base material Hole is in suitable steel/structure as designed—not a thin sheet with two threads of bite
Insufficient engagement means only a few threads take the entire load—stripping risk at a fraction of marked WLL. “It screwed in a little” is not installation.
Shoulder seating
For shoulder eyebolts:
The shoulder must fully contact a flat, clean, load-bearing surface.
Gaps under the shoulder (paint blobs, uneven surfaces, washers that defeat the design, or incomplete threading) destroy the bending-resistance assumption behind angular ratings.
If the shoulder cannot seat, stop—do not invent shims that the manufacturer did not authorize.
Torque and seating concepts (Level I awareness)
Manufacturers specify installation torque or seating procedures for many hoist rings and some eyebolt systems.
Concept Level I takeaway
Snug / specified torque Install to manufacturer torque so the shoulder or flange seats and friction/lock features work
- Under-torqued Can leave gaps, allow shifting under load, reduce rated performance
- Over-torqued Can damage threads, stretch the shank, or crack the base
Re-check after initial load Good practice for some assemblies if manufacturer requires re-torque after first loading
Loctite / locking devices Use only as the manufacturer specifies—do not freestyle chemical locks that prevent required removal inspection
You are not expected to memorize every torque foot-pound value. You are expected to know that eyebolts and hoist rings are installed products , not loose jewelry, and that incomplete seating voids ratings.
Through-hole and nutted styles
Some eyebolts pass through a hole and retain with a nut (and often a washer). Engagement length, nut grade, and protrusion requirements are manufacturer-specific. Apply the same rules: full engagement, correct orientation of the eye to the expected load plane when required, and no angular misuse of plain patterns.
Swivel Hoist Rings for Multi-Directional Loading
Swivel hoist rings (also called swivel lifting rings or hoist rings) are designed so the load can pivot and, on many designs, swivel about the bolt axis while remaining within a rated envelope.
Feature Eyebolt (typical) Swivel hoist ring (typical)
Load direction flexibility Limited; shoulder types have angular tables; non-shoulder essentially in-line only Designed for multi-directional loading within WLL
- Alignment Eye orientation often matters Bail/ring articulates to align with the sling
- Installation Thread engagement + seating critical Thread engagement + manufacturer torque typically critical
Common use case Known in-line or controlled-angle lifts Lifts where the sling will leave at changing angles as the load rises or rotates
- Side-load tolerance Poor on ordinary eyebolts Built into the product rating when used as designed
- When to prefer a swivel hoist ring
The sling will not remain in line with a fixed eye as the crane takes load.
The load may rotate or the hitch will pull from varying directions.
Multiple legs attach to pads where pure vertical eyebolt loading cannot be maintained.
The lift plan or manufacturer documentation specifies hoist rings for the pad pattern.
Installation awareness
Select capacity for the worst-case direction of load on that pad, not a hopeful vertical-only number.
Install with full engagement and specified torque .
Verify the ring swivels/pivots freely before the lift.
Inspect for cracks, bent bails, damaged threads, and missing ID—same remove-from-service mindset as other hardware.
Do not side-load the ring beyond its design (for example, prying under a fixed obstruction).
Common Misuse Patterns and Corrections
Misuse Hazard Correction
Angular load on non-shoulder eyebolt Shank bend / sudden failure In-line only, or change hardware to shoulder/hoist ring per plan
Shoulder eyebolt used at angle without capacity reduction Overload relative to true rating Apply manufacturer angular table; upsize or reconfigure if needed
Only 2–3 threads engaged in soft material Strip-out Full engagement in proper base; repair/re-tap per competent process—do not guess
Shoulder not seated Bending not supported as designed Clean surface; correct length; ensure full seat
Eyebolt eye turned so the pull opens the eye Eye deformation Orient per manufacturer; use hardware that swivels if direction varies
Using a “shop-made” eyebolt from unknown bar stock Unknown capacity Use marked, manufactured lifting hardware only
Coordination with Multi-Leg Bridles
When four shoulder eyebolts on a skid feed a four-leg bridle:
Sling angles mean each pad may see angular components even if the crane hook is centered.
Level the load so legs share as the plan intends; uneven CG shifts angles and forces.
If pads only accept non-shoulder bolts, the plan should keep load in line or specify different hardware— you do not invent angular capacity.
Exam Focus
Distinguish shoulder vs non-shoulder eyebolts; remember angular loading reduces shoulder-eyebolt capacity and is not allowed on non-shoulder types in standard teaching; demand full thread engagement and shoulder seating ; treat torque/seating as part of rated installation; prefer swivel hoist rings when load direction will change or multi-directional loading is expected. Pair with inspection knowledge: bent shanks, stretched eyes, and cracked transitions are remove-from-service conditions that also end the lift.