Study guide
11.1 Shackles and Hooks in Use
NCCCO Rigger Level I Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 About the NCCCO Rigger Level I Exam 1.2 Level I vs Level II Scope 1.3 Eligibility, Fees, and Recertification
2 Scope: Load Path and Characteristics
2.1 Identifying the Load Travel Path 2.2 Load Weight and Center of Gravity 2.3 Attachment Points and Lift Points
3 Scope: Hazards and Unsafe Practices
3.1 Special Handling Requirements 3.2 Pinch Points and Softeners 3.3 Load Stability, Shock Load, and Side Loading 3.4 Electrical Hazards, Body Positioning, and Hazard Communication
4 Technical Knowledge: ASME Standards
4.1 ASME B30.9 Slings and B30.10 Hooks 4.2 ASME B30.26 Hardware and B30.20 Below-the-Hook
5 Technical Knowledge: OSHA Regulations
5.1 OSHA 1910.184 and 1926.251 5.2 OSHA 1926.1401 Qualified Rigger 5.3 OSHA 1926.1431 Hoisting Personnel
6 Inspection: Foundations, Wire Rope, and Chain
6.1 Frequent vs Periodic Inspection 6.2 Wire Rope Sling Inspection and Removal Criteria 6.3 Chain Sling Inspection and Removal Criteria
7 Inspection: Synthetic and Specialty Slings
7.1 Synthetic Web Sling Inspection 7.2 Synthetic Round Sling Inspection 7.3 Metal Mesh and Synthetic Rope Sling Inspection
8 Inspection: Hooks, Hardware, and Below-the-Hook Devices
8.1 Hook Inspection (ASME B30.10) 8.2 Shackles, Eyebolts, and Hardware Inspection 8.3 Below-the-Hook Device Inspection
9 Execution: Sling Types and Identification
9.1 Chain and Wire Rope Sling Use 9.2 Synthetic Web and Round Sling Use 9.3 Sling Identification Tags and WLL
10 Execution: Hitches, Angles, and Capacity
10.1 Vertical, Choker, and Basket Hitches 10.2 Sling Angle Factors 10.3 Hitch Capacity Calculations 10.4 Edge Protection and D/d Ratio
11 Execution: Rigging Hardware in Use
11.1 Shackles and Hooks in Use 11.2 Eyebolts and Swivel Hoist Rings 11.3 Wire Rope Clips and Compression Hardware 11.4 Blocks, Beam Clamps, Softeners, and Related Gear
12 Execution: Below-the-Hook Devices, Tag Lines, and Knots
12.1 Below-the-Hook Lifting Devices 12.2 Tag Line Use and Load Control 12.3 Basic Knots for Riggers
13 Execution: Post-Lift Activities and Communication
13.1 Securing, Disconnecting, and Stowing Gear 13.3 Stop Authority and Lift Communication
14 Practical Exam Prep and Study Strategy
14.1 Level I Practical Exam Tasks 14.2 Study Strategy and Exam Day
11.1 Shackles and Hooks in Use
Key Takeaways Explain This Topic AI
Prefer screw-pin shackles for frequent connect/disconnect with full pin seating; prefer bolt-type (nut + cotter) for permanent, vibrating, or security-critical connections such as multi-leg master links.
Never replace a shackle pin with a random bolt; the pin is part of the rated assembly and must be fully engaged (cotter installed on bolt-type).
Load the shackle bow correctly in plane; avoid side-loading the body and avoid pin-as-lever geometry under tension.
Seat loads in the hook bowl (saddle); never tip-load or side-load; latches retain connections—they do not carry the load.
Prevent overcrowding: gather multiple eyes in a properly rated shackle or master link so a single connector seats fully in the hook.
Last updated: July 2026
11.1 Shackles and Hooks in Use
Quick Answer: Use the correct shackle type (screw-pin for frequent connect/disconnect; bolt-type with nut and cotter for permanent or multi-leg/master-link connections), load the bow properly, keep the pin fully engaged , and never substitute a random bolt for the pin. Seat loads in the hook bowl (saddle) —never tip-load or side-load—and do not overcrowd the hook throat with eyes.
Execution of Rigging Activity is roughly 42% of the NCCCO Rigger Level I written exam. After you can select and inspect slings, you must connect them safely with hardware. Shackles and hooks are the most common connectors on Level I work. This section is about correct use under load , not inspection criteria alone (inspection lives in Domain Inspection; use depends on both).
Level I assumes load weight, CG, and configuration are known or provided . Your job is to assemble the connection so each piece sees load the way it was rated —in plane, fully seated, within WLL, and free of unauthorized field “fixes.”
Screw-Pin vs Bolt-Type Shackles
Feature Screw-pin shackle Bolt-type (safety) shackle
Pin retention Threaded pin screws into the shackle ear Bolt + nut, secured with cotter pin or equivalent retainer
Connect/disconnect speed Fast—preferred for frequent reconfiguration Slower—requires nut and cotter work
Vibration / rotation risk Pin can back out if not fully seated or if load spins the pin Cotter/retainer resists accidental nut loss under vibration
Typical preference Temporary, repeated hitch changes, day-to-day pick points Permanent or semi-permanent connections; multi-leg master links; where the pin might rotate under load
Level I exam cue “Quick connect” / frequent disconnect “Bolt-type with nut and cotter” when security is critical
When screw-pin is preferred
Choose a screw-pin shackle when the lift plan calls for:
Frequent attach/detach of a sling eye to a pad eye or master link.
Temporary connections that will be opened several times per shift.
Situations where you can fully seat the pin and verify it is screwed in until the collar (or designed shoulder) bears properly against the ear.
Still treat screw-pin shackles as precision gear: the pin must be the matched manufacturer pin , fully engaged, and not “finger-tight only for a second.” Under vibration or when the load can rotate the pin, prefer bolt-type if the plan allows.
When bolt-type is preferred
Choose a bolt-type shackle (often called a safety shackle ) when:
The connection will remain assembled for an extended period.
The shackle sits in a multi-leg bridle or as a connector that can experience rotation that might unscrew a plain screw pin.
Site practice, manufacturer guidance, or the lift plan specifically requires nut + cotter retention.
You need a clear “completed assembly” check: nut fully on, cotter installed and spread, pin fully through both ears.
Exam habit: If a scenario emphasizes vibration, long-term connection, or master-link security, bolt-type is the safer selection. If the scenario emphasizes frequent re-rigging with proper pin seating, screw-pin is acceptable.
- Pin Orientation, Engagement, and “Never Use a Random Bolt”
- Correct pin engagement
Align the shackle ears with the connection.
Insert the correct pin for that shackle (size, thread, shoulder).
For screw-pin: screw in until fully seated as designed—do not leave threads showing in a way that means incomplete engagement.
For bolt-type: install the nut and cotter pin (or designed retainer); spread the cotter so the nut cannot back off.
Confirm the bow and pin are free of cracks, bends, and missing identification before tensioning.
Bad practice Why it fails
Substitute bolt from the truck Wrong grade, diameter, shoulder, and material; not a rated pin; threads may not match; no known design factor
- Missing cotter on bolt-type Nut can back off under vibration or rotation
- Partially screwed pin Incomplete load path; pin can walk out
- Cross-threaded pin Damaged engagement; unknown capacity
- Using two half-engaged pins or wire “safety” Not a rated retention method
Never replace the shackle pin with an ordinary bolt. That is a classic Level I fail condition. The pin is part of the rated assembly . Field improvisation voids the WLL assumption even if the bolt “looks strong.”
Load the bow correctly
Shackles are designed so the load primarily loads the bow , with the pin completing the closed connection.
- Loading practice Acceptable? Notes
- Single load on the bow , pin closing the connection Yes Standard use
Two sling eyes on the bow with pin through a pad eye (common) Often yes if capacity and geometry allow Avoid overcrowding that forces side load
Load applied primarily to the pin as a beam with awkward angles Avoid Pin loading and multi-plane side load reduce capacity; follow manufacturer tables
Shackle used as a “spread” device forcing out-of-plane load No Side-loading the body is a misuse unless specifically rated
Stacking multiple eyes so they bind and tip the shackle Correct the geometry Overcrowding creates side/tip loading
Rule of thumb for Level I: Keep loads in the plane the shackle was designed for. If the bow is canted and the pin is bending, stop and reconfigure—often with a larger shackle, a master link, or a different hitch geometry provided in the plan.
Screw-pin orientation tips candidates memorize
Training materials often teach:
Orient the pin so it is less likely to unscrew under expected motion (site SOPs vary; manufacturer and employer rules control).
Always verify full seating after any load that could have vibrated the assembly.
Do not use a shackle with a bent pin , spread bow , or elongated pin holes —those are inspection rejects that also block use.
Hooks in Use — Seat, Latch, and Load Direction
Hooks (on crane blocks, hoist hooks, or sling hooks) must carry the load in the bowl / saddle / base of the hook, in the designed plane of the hook body.
Load in the base (saddle)
Loading location Allowed for ordinary lifting hooks?
- Saddle / bowl (deepest part of the throat) Yes — correct seating
- Tip of the hook No — tip loading
- Latch only No — latches retain, they do not carry the load
Out-of-plane / side load on the hook body No (unless the hook is specifically designed/rated for that load path)
When you hang a sling eye, master link, or shackle on a hook:
Open or manage the latch as designed.
Place the connector fully into the bowl .
Confirm the latch closes over the throat if a latch is required for the application.
Confirm nothing is forcing the connector out onto the tip as tension comes on.
Latches
Latches are retention devices . They help keep the connection from walking off under slack, shock, or contact—not to “hold half the load on the tip.”
If a latch is required by manufacturer, ASME B30.10 practice, employer rule, or the equipment configuration, it must be present and functional before use.
A missing, bent, seized, or spring-failed latch is a remove/repair before use condition when the latch is required.
Never argue that “we always leave latches off on this job” when the governing standard or manufacturer requires them—exam answers favor correct, latch-compliant use.
Never tip-load or side-load
Tip loading happens when the connector rests on the point of the hook instead of the bowl—often because:
Too many eyes are crammed in the throat and crowd toward the tip.
The hook is too small for the master link or shackle body.
Geometry pulls the sling toward the tip as the load rises.
Side loading happens when force is applied out of the plane of the hook (sideways on the body). Ordinary hooks are not general multi-directional lift points. Side load can open the throat, twist the hook, or fail the shank.
- Symptom under rising tension Correct action
- Eye walking toward the tip Lower, re-seat in the bowl, or use a shackle/master link to reduce bulk
- Hook rotating out of plane Correct load path / attachment; do not proceed with side load
- Latch taking bearing load Reconfigure so load is in the saddle
- Multiple eyes binding Use a shackle or link sized for the connection
- Connecting Slings to Hooks and Shackles Without Overcrowding
Overcrowding is a top execution failure. It looks “connected” but creates tip load, uneven loading, and abrasion.
Practical connection patterns
- Connection goal Preferred Level I approach
- One sling eye to crane hook Seat eye fully in bowl; latch closed if required
Two or more sling eyes to one hook Often better: gather eyes in a shackle or master link , hang that single connector in the hook bowl
Sling eye to pad eye Shackle through pad eye; sling on the bow (or per manufacturer guidance for pin vs bow)
Multi-leg bridle Master link / oblong sized for the hook; legs on the master link; avoid stuffing all legs into a small hook throat
Soft sling eye on a narrow hook Ensure eye is not pinched on the tip; use a shackle if the hook width damages the eye
Fit and capacity checks before tension
WLL of each component ≥ the share of load it will carry for the hitch and angles given in the plan.
Hook capacity ≥ applied load (crane charts and hook ratings are separate from sling ratings—do not assume one covers the other).
Physical fit: the connector sits fully in the bowl without forcing.
No contact that will cut synthetics or nick wire rope at the connection.
No crossed or twisted legs that will unequalize multi-leg load as soon as the hoist takes weight.
Exam scenarios to internalize
Scenario A: Two large sling eyes will not both sit in the bowl of a small hook. Answer concept: Use a properly rated shackle or master link so a single connector seats in the bowl—do not force tip loading.
Scenario B: Crew wants to use a Grade 5 hardware bolt because the screw pin was lost. Answer concept: Remove the incomplete shackle from service; replace with a matched pin or complete shackle assembly—never improvise the pin.
Scenario C: Load begins to rise and the shackle is cocked, loading the pin as a lever. Answer concept: Stop, lower, reorient so the bow takes the load in plane.
Scenario D: Hook latch is missing on a configuration that requires a latch. Answer concept: Do not lift until corrected; latches are not optional when required.
Integration with Inspection and Lift Control
Execution and inspection meet at the moment of connection:
A shackle that passed yesterday’s visual check still needs a pre-use look at pin, bow, and markings.
A hook with a functional latch still fails use rules if you tip-load it.
If the lift plan’s hardware list does not match what is in the box, stop and resolve with the person directing the lift—Level I does not freestyle hardware substitution.
Exam Focus
Memorize the use rules: screw-pin vs bolt-type preference cues; full pin engagement; no bolt-for-pin substitution ; load the bow and the hook saddle ; latches retain, they do not carry load; never tip-load or side-load; prevent overcrowding with shackles and master links. Pair this with Chapter 8 inspection knowledge so you both reject bad hardware and use good hardware correctly .