Study guide

1.2 Level I vs Level II Scope

NCCCO Rigger Level I Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 About the NCCCO Rigger Level I Exam 1.2 Level I vs Level II Scope 1.3 Eligibility, Fees, and Recertification

2 Scope: Load Path and Characteristics

2.1 Identifying the Load Travel Path 2.2 Load Weight and Center of Gravity 2.3 Attachment Points and Lift Points

3 Scope: Hazards and Unsafe Practices

3.1 Special Handling Requirements 3.2 Pinch Points and Softeners 3.3 Load Stability, Shock Load, and Side Loading 3.4 Electrical Hazards, Body Positioning, and Hazard Communication

4 Technical Knowledge: ASME Standards

4.1 ASME B30.9 Slings and B30.10 Hooks 4.2 ASME B30.26 Hardware and B30.20 Below-the-Hook

5 Technical Knowledge: OSHA Regulations

5.1 OSHA 1910.184 and 1926.251 5.2 OSHA 1926.1401 Qualified Rigger 5.3 OSHA 1926.1431 Hoisting Personnel

6 Inspection: Foundations, Wire Rope, and Chain

6.1 Frequent vs Periodic Inspection 6.2 Wire Rope Sling Inspection and Removal Criteria 6.3 Chain Sling Inspection and Removal Criteria

7 Inspection: Synthetic and Specialty Slings

7.1 Synthetic Web Sling Inspection 7.2 Synthetic Round Sling Inspection 7.3 Metal Mesh and Synthetic Rope Sling Inspection

8 Inspection: Hooks, Hardware, and Below-the-Hook Devices

8.1 Hook Inspection (ASME B30.10) 8.2 Shackles, Eyebolts, and Hardware Inspection 8.3 Below-the-Hook Device Inspection

9 Execution: Sling Types and Identification

9.1 Chain and Wire Rope Sling Use 9.2 Synthetic Web and Round Sling Use 9.3 Sling Identification Tags and WLL

10 Execution: Hitches, Angles, and Capacity

10.1 Vertical, Choker, and Basket Hitches 10.2 Sling Angle Factors 10.3 Hitch Capacity Calculations 10.4 Edge Protection and D/d Ratio

11 Execution: Rigging Hardware in Use

11.1 Shackles and Hooks in Use 11.2 Eyebolts and Swivel Hoist Rings 11.3 Wire Rope Clips and Compression Hardware 11.4 Blocks, Beam Clamps, Softeners, and Related Gear

12 Execution: Below-the-Hook Devices, Tag Lines, and Knots

12.1 Below-the-Hook Lifting Devices 12.2 Tag Line Use and Load Control 12.3 Basic Knots for Riggers

13 Execution: Post-Lift Activities and Communication

13.1 Securing, Disconnecting, and Stowing Gear 13.3 Stop Authority and Lift Communication

14 Practical Exam Prep and Study Strategy

14.1 Level I Practical Exam Tasks 14.2 Study Strategy and Exam Day

1.2 Level I vs Level II Scope

Key Takeaways Explain This Topic AI

Level I performs simple, repetitive rigging when weight, center of gravity, rigging, and configuration are known or provided.

Level II adds calculating or estimating weight and center of gravity when required.

Level II identifies lift points and selects rigging from loading and load integrity.

Level II may perform the published Level II tasks unsupervised.

The handbook does not define the levels by a universal list of lift labels or one crane-capacity percentage.

Last updated: August 2026

The published distinction

  • Capability Level I Level II addition
  • Weight and center of gravity Uses values that are known or provided Calculates or estimates them when required
  • Lift points Uses the prescribed or known arrangement Identifies lift points

Rigging selection Uses known or prescribed rigging and configuration Determines and selects rigging from loading

Angles and load integrity Applies basic known configurations and capacities Selects with load-angle factors, capacity, and integrity

Independence Performs simple, repetitive known-configuration work Performs the listed Level II tasks unsupervised

Do not replace this competency test with an invented universal rule that every blind, tandem, personnel, “critical,” or above-75%-capacity lift automatically maps to one CCO level. Those operations may require specialized plans, roles, employer controls, signalpersons, engineers, or regulatory compliance, but the CCO Level I/II distinction in the candidate handbook is stated through the skills above. OSHA 1926.1431 also appears in the Level I Technical Knowledge reference list, so the mere presence of personnel-hoisting rules does not prove an item is Level II.

When a task exceeds the rigger’s training, provided information, authority, or employer plan, stop and escalate regardless of credential label.