Study guide
3.2 Pinch Points and Softeners
NCCCO Rigger Level I Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 About the NCCCO Rigger Level I Exam 1.2 Level I vs Level II Scope 1.3 Eligibility, Fees, and Recertification
2 Scope: Load Path and Characteristics
2.1 Identifying the Load Travel Path 2.2 Load Weight and Center of Gravity 2.3 Attachment Points and Lift Points
3 Scope: Hazards and Unsafe Practices
3.1 Special Handling Requirements 3.2 Pinch Points and Softeners 3.3 Load Stability, Shock Load, and Side Loading 3.4 Electrical Hazards, Body Positioning, and Hazard Communication
4 Technical Knowledge: ASME Standards
4.1 ASME B30.9 Slings and B30.10 Hooks 4.2 ASME B30.26 Hardware and B30.20 Below-the-Hook
5 Technical Knowledge: OSHA Regulations
5.1 OSHA 1910.184 and 1926.251 5.2 OSHA 1926.1401 Qualified Rigger 5.3 OSHA 1926.1431 Hoisting Personnel
6 Inspection: Foundations, Wire Rope, and Chain
6.1 Frequent vs Periodic Inspection 6.2 Wire Rope Sling Inspection and Removal Criteria 6.3 Chain Sling Inspection and Removal Criteria
7 Inspection: Synthetic and Specialty Slings
7.1 Synthetic Web Sling Inspection 7.2 Synthetic Round Sling Inspection 7.3 Metal Mesh and Synthetic Rope Sling Inspection
8 Inspection: Hooks, Hardware, and Below-the-Hook Devices
8.1 Hook Inspection (ASME B30.10) 8.2 Shackles, Eyebolts, and Hardware Inspection 8.3 Below-the-Hook Device Inspection
9 Execution: Sling Types and Identification
9.1 Chain and Wire Rope Sling Use 9.2 Synthetic Web and Round Sling Use 9.3 Sling Identification Tags and WLL
10 Execution: Hitches, Angles, and Capacity
10.1 Vertical, Choker, and Basket Hitches 10.2 Sling Angle Factors 10.3 Hitch Capacity Calculations 10.4 Edge Protection and D/d Ratio
11 Execution: Rigging Hardware in Use
11.1 Shackles and Hooks in Use 11.2 Eyebolts and Swivel Hoist Rings 11.3 Wire Rope Clips and Compression Hardware 11.4 Blocks, Beam Clamps, Softeners, and Related Gear
12 Execution: Below-the-Hook Devices, Tag Lines, and Knots
12.1 Below-the-Hook Lifting Devices 12.2 Tag Line Use and Load Control 12.3 Basic Knots for Riggers
13 Execution: Post-Lift Activities and Communication
13.1 Securing, Disconnecting, and Stowing Gear 13.3 Stop Authority and Lift Communication
14 Practical Exam Prep and Study Strategy
14.1 Level I Practical Exam Tasks 14.2 Study Strategy and Exam Day
3.2 Pinch Points and Softeners
Key Takeaways Explain This Topic AI
Pinch points form wherever sling, hardware, or load surfaces close under tension—especially at eyes, hooks, shackles, and edges.
Body parts must stay out of the bight and out of any closing gap before the load is taken up.
Softeners and edge protection protect both the sling and the load from cutting, crushing, and abrasion at contact points.
A softener that is too small, misplaced, or free to fall out does not count as protection once the hitch tightens.
Last updated: July 2026
Pinch Points: Where Energy Concentrates
A pinch point is any location where two objects can close with enough force to crush, cut, or trap body parts—or where a sling can be cut against an edge. In rigging, pinch points are not rare side cases; they are built into almost every hitch the moment tension comes on.
Level I scope work includes recognizing unsafe practices around these points before the hoist signal. You can choose perfect capacity and still get injured or destroy a sling if hands stay in the bight or an unprotected edge saws the body of a synthetic web.
Common Pinch-Point Locations
- Location What closes / what fails People risk Gear risk
- Sling eye on hook or shackle Eye seats; fingers between eye and bowl Crush fingers None if seated cleanly
- Choker hitch sliding on load Running part tightens on standing part Hand in bight Abrasion on sling
- Basket or multi-leg at sharp corner Sling body pulled into edge Hand near corner Cut or crushed sling
- Shackle pin / bolt areas Pin turns or gaps close Pinch on gloves Improper pin seating
- Load against structure during set Gap between load and landing surface Foot/hand crush Side load on gear
- Tag line near sheaves or drum (awareness) Line pulled into machinery Entanglement Damaged line
- Sling-to-Load Interfaces
Wherever the sling bears on the load , force is concentrated on a line or small patch of contact. Sharp corners, unfinished steel, concrete edges, and flange corners act like blades against synthetic webbing and can nick wire rope. Even chain can be side-loaded against a knife edge in a bad wrap.
As the hoist takes weight:
Slack leaves the system.
The sling seeks the lowest-energy path—often deeper into a corner.
Any softener that was poorly placed can walk out.
Anything (including a hand) left in that path gets trapped.
That is why “I’ll just hold the sling here while you boom up” is a classic injury setup.
Hardware Interfaces
Hardware pinch points include:
- Hook bowls — as the eye or link seats, the gap closes
- Shackles — pin engagement and the jaw against a pad eye
- Master links and alloy connectors — multi-leg gathering points
Turnbuckles and adjusting hardware — threads and jaws moving under load (less common on pure Level I basic hitches, but the principle is the same)
Never place fingers between a sling eye and the hook to “center it” after tension starts. Seat the eye fully in the bowl before significant load, with the latch operating freely where latches are used, and keep hands clear during take-up.
Stay Out of the Bight
The bight is the loop or bend of rope/sling where the running part can close on the standing part—or where a loop can tighten around an object (or a limb). In choker hitches especially, the sliding choker point is a dynamic pinch.
Rules that save hands:
- Never put hands or feet inside a sling loop that will tighten
- Never straddle a sling or stand inside a coil that could straighten under tension
- Use a tag line or a tool —not fingers—to guide a sling into position when the hoist is about to take weight
- Communicate “hands clear” before the signal for lift
Clothing and gloves can catch even when the plan was “just a light touch.” Treat any closing gap as energized once the crane or hoist starts to pull.
Softeners and Edge Protection
Softeners (edge protectors, wear pads, corner protectors, blocking, or approved edge guards) do two jobs:
- Protect the sling from cutting, abrasion, and extreme bend radius damage
- Protect the load finish or fragile corner from crushing and marking
They are not optional decoration when the contact geometry is severe. Manufacturer and ASME/OSHA-aligned practice expect protection when edges can damage the sling. A cut synthetic sling can fail with little warning compared with a progressive wire-rope break.
What Counts as a Softener
Effective softeners are materials and shapes that:
- Increase the radius the sling bends around (so the edge is less sharp relative to the sling body)
- Resist sliding out as tension rises
Are compatible with the load (will not contaminate food-grade loads, will not melt on hot work, will not crush to nothing instantly)
Are thick and wide enough for the sling width and load
Examples:
- Commercial corner protectors sized to web width
- Leather or polymer wear pads
- Softeners manufactured for roundslings
Timber blocking or padding when it stays put and actually increases radius (scrap cardboard that collapses is not a plan)
- What Does Not Count
- A single layer of rag that cuts through on first tension
- A pad that falls out when the hitch tightens
- Softeners only on the “pretty side” while the hidden corner still saws the sling
- Using the load’s own sharp shipping crate edge as if it were protection
If you cannot keep protection in place through take-up and travel, change the hitch, add a spreader, or stop and replan.
Practical Placement Technique
A workable field sequence:
Identify contact points with the hitch dry-fitted (no load).
Place softeners so the sling will bear on the protector, not walk off onto the raw edge.
Take slack slowly while watching the softener and sling path—hands clear of the closing gap.
Stop and reset if the protector migrates or the sling seats on an unprotected edge.
Re-check after any reorientation of the load; travel can walk gear.
For chokers, ensure the choker point itself is not creating a cutting action on an unprotected corner. For baskets, watch both sides of the load. For multi-leg, watch where legs wrap flanges or pass near coaming.
Body Mechanics Around Pinch Points
Unsafe body positions near pinch points include:
- Kneeling with a knee under a suspended corner during set-down
- Guiding a load with hands on the landing edge while the gap closes
- Holding a shackle body that can spin and pinch when the pin takes load
- Walking between the load and a wall while the load can swing into the gap
Safer habits:
Push/pull with open palms on broad surfaces only when the load is under control and gaps are stable—or better, use tag lines and stay clear
- Keep feet from under edges during landing
- Use spotters when vision is blocked
- Establish that anyone can call stop if a hand or softener looks wrong
- Connecting Softeners to Capacity Thinking
Softeners do not increase the published working load limit of a sling. They help the sling achieve the capacity it was rated for by preventing localized damage and extreme D/d (bend diameter) abuse. A cut or crushed section can fail well below the tag rating. From a hazards viewpoint: unprotected edges are an unsafe practice even when the math on the tag looks fine.
Exam Focus
Questions often describe a hand in a loop during take-up, a choker on a sharp flange, or a missing edge protector on synthetic web. Correct answers emphasize hands clear of the bight , edge protection at contact points , and resetting gear before continuing —not “go faster so the pinch lasts less time.”