Study guide

2.3 Attachment Points and Lift Points

NCCCO Rigger Level I Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 About the NCCCO Rigger Level I Exam 1.2 Level I vs Level II Scope 1.3 Eligibility, Fees, and Recertification

2 Scope: Load Path and Characteristics

2.1 Identifying the Load Travel Path 2.2 Load Weight and Center of Gravity 2.3 Attachment Points and Lift Points

3 Scope: Hazards and Unsafe Practices

3.1 Special Handling Requirements 3.2 Pinch Points and Softeners 3.3 Load Stability, Shock Load, and Side Loading 3.4 Electrical Hazards, Body Positioning, and Hazard Communication

4 Technical Knowledge: ASME Standards

4.1 ASME B30.9 Slings and B30.10 Hooks 4.2 ASME B30.26 Hardware and B30.20 Below-the-Hook

5 Technical Knowledge: OSHA Regulations

5.1 OSHA 1910.184 and 1926.251 5.2 OSHA 1926.1401 Qualified Rigger 5.3 OSHA 1926.1431 Hoisting Personnel

6 Inspection: Foundations, Wire Rope, and Chain

6.1 Frequent vs Periodic Inspection 6.2 Wire Rope Sling Inspection and Removal Criteria 6.3 Chain Sling Inspection and Removal Criteria

7 Inspection: Synthetic and Specialty Slings

7.1 Synthetic Web Sling Inspection 7.2 Synthetic Round Sling Inspection 7.3 Metal Mesh and Synthetic Rope Sling Inspection

8 Inspection: Hooks, Hardware, and Below-the-Hook Devices

8.1 Hook Inspection (ASME B30.10) 8.2 Shackles, Eyebolts, and Hardware Inspection 8.3 Below-the-Hook Device Inspection

9 Execution: Sling Types and Identification

9.1 Chain and Wire Rope Sling Use 9.2 Synthetic Web and Round Sling Use 9.3 Sling Identification Tags and WLL

10 Execution: Hitches, Angles, and Capacity

10.1 Vertical, Choker, and Basket Hitches 10.2 Sling Angle Factors 10.3 Hitch Capacity Calculations 10.4 Edge Protection and D/d Ratio

11 Execution: Rigging Hardware in Use

11.1 Shackles and Hooks in Use 11.2 Eyebolts and Swivel Hoist Rings 11.3 Wire Rope Clips and Compression Hardware 11.4 Blocks, Beam Clamps, Softeners, and Related Gear

12 Execution: Below-the-Hook Devices, Tag Lines, and Knots

12.1 Below-the-Hook Lifting Devices 12.2 Tag Line Use and Load Control 12.3 Basic Knots for Riggers

13 Execution: Post-Lift Activities and Communication

13.1 Securing, Disconnecting, and Stowing Gear 13.3 Stop Authority and Lift Communication

14 Practical Exam Prep and Study Strategy

14.1 Level I Practical Exam Tasks 14.2 Study Strategy and Exam Day

2.3 Attachment Points and Lift Points

Key Takeaways Explain This Topic AI

Prefer manufacturer-designed, rated lift points (lugs, eyes, trunnions) over improvised attachment to random structural members

The number and location of attachment points must share the load appropriately relative to weight and center of gravity

Inspect attachment integrity—cracks, bent lugs, corrosion, missing fasteners, and questionable welds are stop conditions

Match hardware geometry to the attachment (shackle size/orientation, hoist rings vs eyebolts, angular loading limits)

Last updated: July 2026

Why Attachment Points Belong in "Scope"

Before you select a sling or shackle, you must know where the gear will connect to the load. On the NCCCO Rigger Level I outline, identifying attachment points (also called lift points ) sits inside Scope of the Rigging Activity . That placement is deliberate: attachment choice is part of defining whether a lift is a simple, known configuration—or a problem that needs redesign.

An attachment point is any location on the load intended or used to transfer lifting force into the load structure. Good attachment points are:

  • Designed for lifting (not merely convenient holes)
  • Located so the load is controlled relative to the center of gravity
  • Strong enough for the direction of pull that will actually occur
  • Compatible with the hardware you will use
  • In serviceable condition on the day of the lift
  • Designed Lift Points vs Improvised Attachments
  • Designed / manufacturer-rated lift points

Many machines, skids, transformers, and fabricated assemblies ship with dedicated lift features:

  • Designed feature Typical use notes
  • Lifting lugs / padeyes Welded or bolted plates with holes sized for shackles
  • Lift eyes / eyebolts (rated) Threaded or welded eyes with marked capacity and orientation limits
  • Trunnions / lift shafts Cylindrical pins for hooks or special links
  • Integrated hoist rings Swivel hardware designed for angular loading when used as rated

Lifting frames / shipping frames with certified points Temporary or permanent frames with identified pick points

Manufacturer drawings, lift diagrams, and nameplates often show which points to use, how many points, and what orientation is allowed (vertical only vs multi-directional). For Level I work, treating manufacturer lift instructions as part of the "known configuration" is exam-sound and job-sound.

Improvised attachments

Improvised attachment means connecting to a member that was not identified as a lift point—examples include random holes in web members, process piping, handrails, electrical conduit, temporary scaffold lugs, or "that stout-looking angle." Improvisation is a major red flag because:

  • Capacity and weld design may be unknown
  • The member may deform or tear at far less than sling capacity
  • Load path through the structure may damage internal components
  • CG control may be accidental rather than planned

Level I rule of judgment: if the lift depends on an improvised point without a known rating or qualified approval, do not treat it as a normal simple lift . Escalate to a qualified person / engineer. Exam answers that endorse chaining to unknown structure "because it looks strong" are wrong.

Number of Points and Sharing the Load

Attachment count and layout determine how weight is shared among legs and fittings.

Common patterns

  • Arrangement Concept Level I focus
  • Single-point One attachment under the hook line CG must be nearly under the point or the load will tilt/spin

Two-point Pair of points, often with two-leg bridle Points should straddle CG; unequal spacing or offset CG → unequal share

Three-point Three attachments Can improve stability on some loads; still needs known geometry

Four-point Four attachments Common on skids; true equal share only with level hang and proper geometry—not automatic

Important: four points do not automatically mean each leg carries 25 percent of the weight. On a rigid load with a four-leg bridle, two legs can carry most of the load if the load is slightly out of level or CG is offset—unless a below-the-hook device or engineered spreader equalizes share. Level I candidates should recognize unequal sharing as a real risk, not assume perfect division by leg count.

Matching points to CG

Recall from the previous section: the load hangs with CG below the resultant of the supports. Therefore:

  • Place attachment points so the resultant can align above the CG for a controlled hang
  • Prefer manufacturer point sets designed around the known CG
  • If only two points are available and CG is far outside the pair, expect severe tilt—stop and reconfigure
  • Never "fix" a bad point layout by standing on the light end or pushing the load with your body
  • Integrity of Attachment Points

A designed lug that is damaged is no longer a reliable designed point. Inspect before connecting hardware:

  • Visual / tactile checks (frequent, practical)
  • Cracks at welds, holes, or base metal—especially at high-stress corners
  • Bent or deformed lugs, elongated holes, or twisted eyes
  • Corrosion / section loss that reduces thickness or blurs edges of holes
  • Missing or loose fasteners on bolted padeyes or frames
  • Undercut, porosity, or obvious poor welds when welds are visible and suspect
  • Painted-over damage or fresh grinding that hides defects
  • Modifications —flame-cut holes, added plates of unknown origin, re-welded cracks
  • Condition Typical action
  • Crack in lug or weld Remove from service as a lift point; do not use
  • Elongated shackle hole Reject; hole no longer matches hardware properly
  • Heavy corrosion with unknown remaining thickness Do not use until qualified evaluation
  • Missing bolt in multi-bolt padeye Do not use until restored to design condition
  • Slight surface rust, sound metal, hole true Clean, reassess; may be acceptable if no section loss of concern

If integrity is doubtful, stop . Replacing a sling does not fix a bad lug. The weak link may now be the load itself.

Matching Hardware to Attachment Geometry

Even a perfect lug can be used incorrectly if the hardware does not fit the geometry.

Fit and orientation basics

Shackle pin and bow: pin should seat fully; bow must have room to articulate without side-loading the lug beyond its design

Hole diameter: too small → force-fit damage; too large → point loading and odd shackle angles

Thickness of lug: pin must engage properly; washers or spacers only as appropriate—not as improvisation that reduces capacity

Direction of pull: many eyebolts are rated primarily for vertical loading along the axis; angular pulls can drastically cut capacity or bend the shank

Shoulder vs non-shoulder eyebolts: angular loading rules differ—follow manufacturer ratings; when angular load is expected, swivel hoist rings are often the correct designed solution

Multiple legs into one hole: overcrowding changes angles and can side-load fittings; use hardware rated for the connection (for example, a master link or properly sized shackle arrangement)

Geometry mismatches that fail exams and jobs

  • Mismatch Why it is wrong
  • Tiny shackle in oversized hole with severe cocking Point loads, odd angles, possible pin bending
  • Eyebolt pulled at a sharp angle without rating for that angle Bending and reduced capacity
  • Hook tip loaded in a lift eye Hooks are for seating in the bowl, not tip loading
  • Chain or wire choked on a sharp thin lug edge without protection Damages gear and concentrates stress

Connecting to a lift point rated for shipping only after "do not lift" mark is present Follow current markings and procedures

Attachment Points and the Known Configuration

Level I simple lifts assume a known rigging configuration . Attachment points are part of that configuration:

  • Known which points to use
  • Known that those points are appropriate for the lift direction
  • Known relationship to weight and CG
  • Gear selected to match those points

If the only available holes require a nonstandard multi-directional pull, unknown capacity, or complex below-the-hook tooling not provided in the plan, recognize that you may be leaving the "simple known" envelope. Stopping is a competent rigger skill—not a failure.

  • Worked Scenarios
  • Scenario A — Four factory lugs

A skid has four factory lifting lugs marked on the drawing for vertical lifts with a four-leg bridle. All lugs are straight, holes true, welds intact. CG mark is centered. Correct approach: use the four designed points with hardware that fits the holes, confirm leg geometry for the known weight, and keep pulls within the lug design (typically in-plane / as drawn).

Scenario B — Convenient process nozzle

A pump has no accessible lugs because of temporary insulation, but a large process flange looks sturdy. A crew member suggests shackling to the flange bolts. Correct approach: treat the flange as not a designed lift point unless documentation says otherwise. Remove insulation or use the manufacturer lift method; do not improvise on process connections.

Scenario C — Damaged padeye

One of two padeyes shows a visible crack at the weld toe. The other is perfect. Someone proposes a single-leg lift from the good eye because "the load is light." Correct approach: reject the damaged system. A two-point design with one failed point is not automatically safe as a single-point lift—CG, stability, and ratings may not support it. Repair/engineering required.

Scenario D — Hardware mismatch

A rated hoist ring is specified for angular loading on a machine tool. The rigger substitutes a standard eyebolt of similar thread size. Correct approach: substitution is not equivalent. Thread size ≠ lift rating or angular capacity. Use the specified swivel hoist ring or another manufacturer-approved fitting.

Integration With Path and Weight

Attachment decisions feed the rest of Scope:

  • Weight/CG determine how many points you need and where they must sit
  • Attachment integrity determines whether those points are usable today
  • Hardware match determines whether the connection will apply force as designed
  • Path must still clear once the load hangs from those points at its true attitude
  • Exam Traps for Attachment Points
  • Trap Sound answer
  • "Any hole that fits a shackle is a lift point" Only designed/approved points with integrity
  • "Four legs mean 25% each" Share is not automatically equal
  • "Crack is fine if we go slow" Damaged lift points are out of service
  • "Eyebolt and hoist ring are interchangeable" Ratings and angular capacity differ
  • "Looks strong enough" Strength must be known, not guessed

Master attachment-point identification and you close the Scope triangle with path and weight/CG: know where the load will go, know what it weighs and how it balances, and know exactly where—and how—the gear will connect.