Study guide
2.2 Load Weight and Center of Gravity
NCCCO Rigger Level I Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 About the NCCCO Rigger Level I Exam 1.2 Level I vs Level II Scope 1.3 Eligibility, Fees, and Recertification
2 Scope: Load Path and Characteristics
2.1 Identifying the Load Travel Path 2.2 Load Weight and Center of Gravity 2.3 Attachment Points and Lift Points
3 Scope: Hazards and Unsafe Practices
3.1 Special Handling Requirements 3.2 Pinch Points and Softeners 3.3 Load Stability, Shock Load, and Side Loading 3.4 Electrical Hazards, Body Positioning, and Hazard Communication
4 Technical Knowledge: ASME Standards
4.1 ASME B30.9 Slings and B30.10 Hooks 4.2 ASME B30.26 Hardware and B30.20 Below-the-Hook
5 Technical Knowledge: OSHA Regulations
5.1 OSHA 1910.184 and 1926.251 5.2 OSHA 1926.1401 Qualified Rigger 5.3 OSHA 1926.1431 Hoisting Personnel
6 Inspection: Foundations, Wire Rope, and Chain
6.1 Frequent vs Periodic Inspection 6.2 Wire Rope Sling Inspection and Removal Criteria 6.3 Chain Sling Inspection and Removal Criteria
7 Inspection: Synthetic and Specialty Slings
7.1 Synthetic Web Sling Inspection 7.2 Synthetic Round Sling Inspection 7.3 Metal Mesh and Synthetic Rope Sling Inspection
8 Inspection: Hooks, Hardware, and Below-the-Hook Devices
8.1 Hook Inspection (ASME B30.10) 8.2 Shackles, Eyebolts, and Hardware Inspection 8.3 Below-the-Hook Device Inspection
9 Execution: Sling Types and Identification
9.1 Chain and Wire Rope Sling Use 9.2 Synthetic Web and Round Sling Use 9.3 Sling Identification Tags and WLL
10 Execution: Hitches, Angles, and Capacity
10.1 Vertical, Choker, and Basket Hitches 10.2 Sling Angle Factors 10.3 Hitch Capacity Calculations 10.4 Edge Protection and D/d Ratio
11 Execution: Rigging Hardware in Use
11.1 Shackles and Hooks in Use 11.2 Eyebolts and Swivel Hoist Rings 11.3 Wire Rope Clips and Compression Hardware 11.4 Blocks, Beam Clamps, Softeners, and Related Gear
12 Execution: Below-the-Hook Devices, Tag Lines, and Knots
12.1 Below-the-Hook Lifting Devices 12.2 Tag Line Use and Load Control 12.3 Basic Knots for Riggers
13 Execution: Post-Lift Activities and Communication
13.1 Securing, Disconnecting, and Stowing Gear 13.3 Stop Authority and Lift Communication
14 Practical Exam Prep and Study Strategy
14.1 Level I Practical Exam Tasks 14.2 Study Strategy and Exam Day
2.2 Load Weight and Center of Gravity
Key Takeaways Explain This Topic AI
Level I lifts assume load weight and center of gravity (CG) are known or provided—but the rigger must still verify shipping marks, drawings, scales, or manufacturer data
Never guess weight; if weight or CG must be calculated from incomplete data, the work is outside normal Level I simple-lift assumptions and needs Level II / competent-person support
Balanced CG keeps legs sharing load more evenly; offset CG shifts demand to one side and can tilt, overload a leg, or destabilize the load
- CG location relative to attachment points drives sling angles, stability, and whether the load will hang level
- Last updated: July 2026
Weight and CG in the Level I Scope
NCCCO defines Rigger Level I work around simple, repetitive lifts when critical load data are known . Two of the most important known values are:
Load weight — how heavy the object is (including contents, packaging, and attached appurtenances that will lift with it)
Center of gravity (CG) — the balance point of the load’s weight; the point through which the resultant weight acts
Level I does not mean you ignore weight. It means the exam and the job expect weight and CG to be provided or readily verifiable , not invented on the spot. Your skill is to confirm those values, understand how CG affects the hitch, and refuse the lift when the numbers are missing or untrustworthy.
Verify — Do Not Assume
"Known" weight still requires verification. Prefer independent, documented sources:
Source What it typically provides Watch-outs
Manufacturer nameplate / data plate Empty equipment weight, sometimes CG notes Missing plates; modifications not reflected
Shop / fabrication drawings Design weight, CG mark, lift-point locations "Estimated" weights; field-added components
- Shipping marks / bill of lading As-shipped weight Crating vs net weight confusion
- Certified scale / load cell Measured weight Scale not zeroed; partial support still on truck
Lift plan or engineered procedure Stated weight and CG for that lift Plan superseded by a different load configuration
Prior documented weigh tickets Historical weight for identical loads Contents changed since last weigh
Verification habits that save careers:
- Match the identity of the load (serial, tag, description) to the document you are reading
- Confirm whether the number is net , gross , or shipping weight
- Add contents (oil, product, water, tools left inside) if the plate lists only empty weight
- Account for skids, cribbing, and temporary attachments that will ride with the load
- If two sources disagree, stop and resolve the conflict before selecting gear
- Never guess weight
Guessing is not a Level I method. Statements like "it looks like about a ton" or "we lifted one like this last year" are not verification. On exam scenarios, any option that treats estimate-by-eye as acceptable is almost always wrong. If no reliable weight is available, the correct action is to obtain weight (weigh, get manufacturer data, engineered calculation by a qualified person)—not to pick a sling based on feel.
When Calculation Is Required: Level II Territory
Some situations require calculating weight or CG rather than reading a known value:
- Irregular fabrications with no plate or drawing weight
- Partially full vessels or mixed materials
- Multiple objects lifted as one assembly without a combined weight
- Offset machines where CG must be located from component weights and distances
NCCCO Rigger Level II expands into more complex rigging problems, including situations where load weight and CG are not simply provided. For Level I study, remember the boundary:
- Situation Level I expectation
- Weight on plate matches drawing; CG marked Verify and use
- Weight provided on lift ticket; configuration unchanged Verify and use
- Weight unknown; must estimate volume × density without support Stop / escalate — not Level I improvisation
CG unknown on irregular load; multi-leg share must be calculated from first principles Escalate to Level II / qualified person
You may still see simple applied questions (for example, reading a stated weight and choosing adequate WLL). That is verification and application, not inventing missing data.
What Center of Gravity Means Under the Hook
The load will hang so that the CG is directly below the hook (along the line of support) once motion settles. Practical consequences:
If attachment points and the hitch place the resultant above a CG that is centered between them, the load tends to hang level
- If the hitch resultant is not above the CG, the load tilts until the CG lines up under the support
- Tilting changes leg loads , edge contact, and clearance along the travel path
- Balanced vs offset CG
CG condition Typical appearance Effect on rigging
Balanced / centered Symmetric object, CG near geometric center More even leg sharing on symmetric hitches; hangs near level
- Offset longitudinally Motor at one end of a skid Heavier end drops; near-end leg(s) take more load
- Offset laterally Side-mounted gearbox or piping Side tilt; unequal share between left/right legs
- High CG Tall vertical vessel More tip-sensitive; small horizontal forces create large moments
- Low CG Flat plate or low skid More stable against tipping for the same base
Rule of thumb for multi-leg hitches: the leg(s) closer to the CG carry more of the load. An offset CG is not automatically unsafe, but it must be known so that:
- Attachment points and hitch type still control the load
- No single leg or fitting is overloaded
- The planned path still has clearance when the load hangs at its true attitude
- How CG Affects Sling Angles and Stability
Sling included angles and horizontal angles depend on where the attachment points sit relative to the hook and to each other. CG location interacts with that geometry:
Level hang assumption breaks when CG is offset — measured sling lengths that look equal may still produce unequal tension.
Increasing horizontal distance between attachment points (or lowering the hook relative to the spread) changes angles and the load in each leg.
Choker or single-wrap arrangements on offset loads can roll or slip toward the heavy end if not controlled.
Stability suffers when the CG is high and the effective base (distance between support points) is narrow.
Level I candidates should be able to reason qualitatively:
- Steeper sling angles (closer to vertical) generally reduce tension for a given share of weight
- Flatter angles increase tension and horizontal forces at attachment points
An offset CG can push one leg into a flatter effective share of load than the drawing suggests if the load tilts
Detailed angle-factor arithmetic is reinforced later in Execution domains; here the Scope lesson is: you cannot judge capacity or stability without knowing weight and where the CG sits relative to the lift points.
- Worked Scenarios: Known Weight Verification
- Scenario A — Nameplate vs contents
A pump skid nameplate lists 1,850 lb . The drawing notes the plate weight is dry . Field crew filled the oil reservoir (estimated 40 lb) and left a 25 lb toolbox welded to the skid for shipping. Verified lift weight is not 1,850 lb — it is at least 1,915 lb plus any remaining packaging. Selecting gear for 1,850 lb alone is incorrect. Exam takeaway: read what the number includes.
Scenario B — Two documents disagree
Bill of lading says 3,200 lb . Shop drawing says 2,750 lb . No scale is available on site. Correct action: do not average and do not pick the lower number for convenience. Stop, investigate (scale, manufacturer confirmation, engineering), and use a reliable figure. Conservative temporary practice on some sites is to plan with the higher credible value only after a competent person accepts that approach—but inventing a middle value is never correct.
Scenario C — Offset CG mark
A generator skid has a painted CG mark closer to the radiator end. Two vertical legs are planned at equal distances from the geometric center—not from the CG mark. Expected result: the radiator end hangs lower and the near-side leg carries more load. Correct Level I response: reposition attachment points (or use a configuration specified for that CG) so the support lines keep the load controlled and legs within capacity. Do not "see what happens" after hoist.
Scenario D — Scale check
A fabricator provides a certified weigh ticket of 4,100 lb for the exact assembly with shipping frame. Frame will be removed before the lift. Correct verification: obtain weight without the frame or weigh again after removal. Using 4,100 lb after removing a 600 lb frame overstates weight (capacity-wise safer but may confuse path/crane charts); using 4,100 lb when the frame stays on is correct only if the frame truly lifts with the load.
- Practical Verification Sequence (Exam-Ready)
- Identify the exact load to be lifted
- Collect weight evidence (plate, drawing, ticket, scale)
- Adjust for contents and attachments that ride along
- Locate CG from marks, drawings, or provided lift data
- Compare CG to planned attachment points
- Confirm the load will hang in an attitude that keeps the path clear
- If weight or CG cannot be verified, stop — do not guess
- Linking Weight/CG to the Rest of Scope
Weight and CG feed every later decision:
- Hardware and sling selection depend on forces, not hope
- Attachment point choice must straddle or align with CG appropriately
- Path clearances depend on how the load will hang and tilt
- Special handling (fragile corners, liquids, long loads) often ties back to CG height and offset
- Common Exam Traps
- Trap Correct thinking
- "Level I never needs weight" Level I needs known weight; you still verify it
- "Use the lighter document to save capacity" Resolve conflict; never choose the convenient low number
- "CG is always the geometric center" Only if the object is uniform/symmetric or CG is marked there
- "Guess from size" Never guess; obtain data
- "Equal sling lengths always equal leg loads" Offset CG and unequal angles create unequal loads
"If it lifts an inch level, CG must be perfect" Momentary hang can change as legs settle; verify geometry first
If you can verify weight, locate CG, and explain how an offset shifts leg load and hang attitude, you have the Level I Scope foundation for safe simple lifts—and for the weight/CG items on the written exam.