Study guide
5.2 OSHA 1926.1401 Qualified Rigger
NCCCO Rigger Level I Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 About the NCCCO Rigger Level I Exam 1.2 Level I vs Level II Scope 1.3 Eligibility, Fees, and Recertification
2 Scope: Load Path and Characteristics
2.1 Identifying the Load Travel Path 2.2 Load Weight and Center of Gravity 2.3 Attachment Points and Lift Points
3 Scope: Hazards and Unsafe Practices
3.1 Special Handling Requirements 3.2 Pinch Points and Softeners 3.3 Load Stability, Shock Load, and Side Loading 3.4 Electrical Hazards, Body Positioning, and Hazard Communication
4 Technical Knowledge: ASME Standards
4.1 ASME B30.9 Slings and B30.10 Hooks 4.2 ASME B30.26 Hardware and B30.20 Below-the-Hook
5 Technical Knowledge: OSHA Regulations
5.1 OSHA 1910.184 and 1926.251 5.2 OSHA 1926.1401 Qualified Rigger 5.3 OSHA 1926.1431 Hoisting Personnel
6 Inspection: Foundations, Wire Rope, and Chain
6.1 Frequent vs Periodic Inspection 6.2 Wire Rope Sling Inspection and Removal Criteria 6.3 Chain Sling Inspection and Removal Criteria
7 Inspection: Synthetic and Specialty Slings
7.1 Synthetic Web Sling Inspection 7.2 Synthetic Round Sling Inspection 7.3 Metal Mesh and Synthetic Rope Sling Inspection
8 Inspection: Hooks, Hardware, and Below-the-Hook Devices
8.1 Hook Inspection (ASME B30.10) 8.2 Shackles, Eyebolts, and Hardware Inspection 8.3 Below-the-Hook Device Inspection
9 Execution: Sling Types and Identification
9.1 Chain and Wire Rope Sling Use 9.2 Synthetic Web and Round Sling Use 9.3 Sling Identification Tags and WLL
10 Execution: Hitches, Angles, and Capacity
10.1 Vertical, Choker, and Basket Hitches 10.2 Sling Angle Factors 10.3 Hitch Capacity Calculations 10.4 Edge Protection and D/d Ratio
11 Execution: Rigging Hardware in Use
11.1 Shackles and Hooks in Use 11.2 Eyebolts and Swivel Hoist Rings 11.3 Wire Rope Clips and Compression Hardware 11.4 Blocks, Beam Clamps, Softeners, and Related Gear
12 Execution: Below-the-Hook Devices, Tag Lines, and Knots
12.1 Below-the-Hook Lifting Devices 12.2 Tag Line Use and Load Control 12.3 Basic Knots for Riggers
13 Execution: Post-Lift Activities and Communication
13.1 Securing, Disconnecting, and Stowing Gear 13.3 Stop Authority and Lift Communication
14 Practical Exam Prep and Study Strategy
14.1 Level I Practical Exam Tasks 14.2 Study Strategy and Exam Day
5.2 OSHA 1926.1401 Qualified Rigger
Key Takeaways Explain This Topic AI
Under OSHA 1926.1401, a qualified rigger is a rigger who meets the criteria for a qualified person—training, knowledge, and experience to solve rigging problems related to the work.
The employer determines qualification through demonstrated training/knowledge/experience or by relying on third-party certification such as NCCCO Rigger credentials for the lifts those credentials cover.
Subpart CC requires a qualified rigger during crane assembly/disassembly and when employees are in the fall zone hooking, unhooking, or guiding a load (among specified situations).
NCCCO Rigger Level I supports basic, known-configuration work; more complex lifts may require higher competence, additional qualifications, or specialized lift planning beyond routine Level I scope.
Holding a card does not automatically authorize every lift type—match qualification to the task, and stop if the work exceeds your demonstrated competence or certified scope.
Last updated: July 2026
5.2 OSHA 1926.1401 Qualified Rigger
Quick Answer: A qualified rigger (OSHA 1926.1401 ) is a rigger who meets the criteria for a qualified person —someone with the training, knowledge, and experience to solve problems related to the rigging work. The employer decides qualification via demonstrated competence or third-party certification (e.g., NCCCO ). Subpart CC requires a qualified rigger for crane assembly/disassembly and when workers are in the fall zone hooking, unhooking, or guiding a load. Level I supports basic lifts; complex work may need higher competence.
Technical Knowledge on the Level I outline is not only sling standards—it includes knowing who is allowed to perform certain crane-related rigging tasks under OSHA’s construction crane rule ( Subpart CC , 29 CFR 1926.1400 and following). The definition lives in 1926.1401 ; the duty moments live in related sections such as assembly/disassembly and working under loads.
Definitions You Must Separate
Term Plain meaning for Level I
Qualified person (general OSHA idea) Person who, by degree, certificate, professional standing, or extensive knowledge, training, and experience, has demonstrated the ability to solve problems related to the subject matter, work, or project
Qualified rigger (1926.1401) A rigger who meets the criteria for a qualified person
Competent person Person capable of identifying hazards and with authority to take corrective measures—different role from “qualified”
Certified rigger (NCCCO) Third-party credential documenting knowledge/skill; often used by employers as evidence of qualification for covered work
Signal person Separate Subpart CC role with its own qualification/certification path—not the same as rigger
Exam trap: Qualified rigger ≠ signal person ≠ crane operator. A worker may hold more than one qualification, but the standards define different competencies. Passing a signal test does not automatically make someone a qualified rigger for assembly/disassembly.
Exam trap: Competent person authority (stop work, correct hazards) is not identical to qualified person technical problem-solving. Do not swap the words on multiple-choice items.
The OSHA Definition in Working Language
OSHA’s construction crane standard defines a qualified rigger as a rigger who meets the criteria for a qualified person . In practice, that means the person can:
- Select and configure rigging appropriate to the load and hitch for the assigned work
- Recognize when the configuration is wrong, overloaded, or unstable
- Apply knowledge of capacities, angles, hardware, and load control
- Solve problems related to the rigging —not merely “follow a coworker’s guess”
- Operate within the limits of their demonstrated competence for that task
The definition is performance-based . It does not list “five years on the job” as a magic number. Time helps only when it produces demonstrated ability .
Who Determines Qualification?
Path How it works
Employer determination Employer evaluates training, knowledge, and experience and determines the person can perform the rigging work safely and competently
Third-party certification Employer relies on a recognized certification (such as NCCCO Rigger Level I or II ) as documentation that the person has met an independent knowledge and skill standard for the level certified
Task-specific limits Qualification is not infinite: complex lifts, multi-crane work, or personnel platforms may require additional qualifications, procedures, or higher-level certs
Key point for the exam: OSHA places the employer in the position of ensuring a qualified rigger is used when the standard requires one. Certification is a powerful tool for that determination, but assigning an unqualified person “because they are available” is a compliance failure—even if that person has a strong back and a radio.
Key point for the job: Your CCO Level I card is strong evidence for basic rigging competence. It does not mean every lift on a mega-project is automatically inside your personal qualification envelope. Employer procedures, lift plans, and Level II / specialized roles still matter.
When Subpart CC Requires a Qualified Rigger
Two high-yield triggers every Level I candidate should own:
1. Assembly and disassembly of the crane
During assembly/disassembly (A/D) of a crane, OSHA requires a qualified rigger for the rigging work involved in that process (as specified in the A/D provisions). A/D is high-risk: boom sections, counterweights, pins, and out-of-configuration loads. The qualified rigger supports safe configuration of those loads under the A/D director’s overall process.
2. Employees in the fall zone who are hooking, unhooking, or guiding the load
When workers must be in the fall zone of a suspended load to hook , unhook , or guide the load, OSHA requires that the work be done by a qualified rigger (within the applicable Subpart CC work-under-load rules). The idea is simple: if a person is exposed because the load still needs hands-on connection or guidance, that person must be a qualified rigger , not a random bystander “helping the load.”
- Situation Qualified rigger required? (concept)
- Crane A/D rigging tasks under Subpart CC Yes — use a qualified rigger as required
- Hooking/unhooking/guiding while in the fall zone Yes — qualified rigger
Routine material lift with all personnel clear of the fall zone and no Subpart CC trigger Other rules still apply (safe rigging, 1926.251, employer program); the specific “qualified rigger” trigger depends on the activity
Signal person only, no rigging Different qualification
Exam trap: The requirement is not “anyone standing near a crane must be a certified rigger.” It is tied to defined activities —especially A/D and hooking/unhooking/guiding in the fall zone . Learn the triggers, not a vague “always/never.”
Exam trap: Keeping people out of the fall zone is still the preferred control. The standard does not invent a free pass to stand under loads because someone is “qualified.” Qualification enables necessary exposure under controlled rules; it does not authorize casual under-load hanging out.
Level I Certification vs. “More Complex Lifts”
NCCCO Rigger Level I is designed around simple, repetitive tasks when load weight, center of gravity, rigging, and configuration are provided or known . That aligns well with many employer determinations for basic lifts under Subpart CC.
- Work character Typical competence frame
- Known weight/CG, prescribed hitch, repetitive plant or site move Level I–type competence often appropriate
- Weight/CG must be calculated; rigger selects gear based on loading unsupervised Level II–type competence
- Multi-crane, blind lifts, engineered critical lifts Specialized planning + higher competence
- Personnel hoisting (1926.1431) Highly regulated; not routine Level I tasking
- Crane A/D Qualified rigger required; may need site-specific A/D training beyond basic Level I book knowledge
Scenario — Level I fits: A certified Level I rigger hooks a pre-planned two-leg basket on a known-weight palletized load, guides with a tag line from outside the fall zone where feasible, and unhooks after the load is set and secured. Weight and configuration were known; employer accepts Level I certification as qualification for this basic lift.
Scenario — escalate: An irregular module arrives with no reliable weight data. Someone must calculate weight and CG, choose angles and hardware, and decide attachment points. That is not “configuration already known.” Use Level II (or equivalent demonstrated competence) and a proper plan—do not stretch Level I scope because the schedule is tight.
Scenario — fall zone: A load must be guided into a tight pocket and a worker must place a hand near the load to seat it. That worker needs to be a qualified rigger , and the operation needs clear signals, controlled hoist motion, and minimized exposure—not “everyone grab a corner.”
Employer Programs and Your Personal Stop Authority
Even with a card in your wallet:
Verify the task matches your qualification. If the lift plan assumes Level II decisions, say so.
Follow site procedures. Some owners require certification and site orientation and a lift plan signature chain.
Refuse unsafe assignments. Qualification is not consent to overload, missing tags, or standing under free-swinging loads.
Document training when asked. Employers may keep records of how they determined qualification.
Common Wrong Answers on “Who Is Qualified?”
- Wrong belief Why it fails
- “Anyone on the crew today” No demonstrated problem-solving competence
- “Five years experience automatically” Time alone ≠ qualified person criteria
- “Only a state journeyman card” Trade license ≠ automatic rigger qualification under 1926.1401
“Only NCCCO counts; employer training never does” Employer may determine qualification by training/knowledge/experience or use third-party cert
“Level I covers personnel platforms and multi-crane criticals by default” Those are specialized / higher-complexity
How This Links to Other Chapters
Section 1.2 (Level I vs Level II): Maps NCCCO scope to task complexity—the same boundary employers should respect when assigning “qualified rigger” duties.
Section 5.1: Qualified people still need legal gear under 1910.184 / 1926.251.
Section 5.3: Personnel hoisting is a separate, stricter regime—do not assume rigger qualification alone authorizes riding the headache ball or an improvised platform.
Inspection & Execution domains: Being “qualified” includes knowing when gear fails inspection and how to attach hitches correctly.
Bottom Line for Section 5.2
A qualified rigger is a rigger who is a qualified person for the rigging problem at hand. Employers determine that status through competence or recognized certification such as NCCCO . Subpart CC requires qualified riggers for assembly/disassembly and for hooking, unhooking, or guiding loads when workers are in the fall zone . Level I is strong evidence for basic work; complex lifts need higher competence and planning. Know the definition, the determination paths, and the duty triggers cold.