Study guide

7.1 Two-Leg Tension and Angle Reference

NCCCO Rigger Level II Exam

Track your progress as you read

Finished sections get a check mark.

1 Certification and Exam Preparation

1.1 Current Exam, Eligibility and Scheduling 1.2 Practical Tasks and Examination-Specific Rules 1.3 Study Method, References and Recertification

2 Identify and Measure the Load

2.1 Load Identity, Dimensions and Units 2.2 Load Weight, Density and Complete Inventories 2.3 Composition, Structural Integrity and Special Handling

3 Center of Gravity and Support Geometry

3.1 Center of Gravity and Suspended Stability 3.2 Attachment Points and Complete Force Paths 3.3 Final Position, Landing Supports and Derigging Access

4 Route and Site Hazards

4.1 Travel Path, Clearance and Work-Zone Control 4.2 Power Lines, Clearance Options and Electrical Response 4.3 Weather, Temperature and Ground Conditions

5 Team Duties and Communications

5.1 Signalperson Duties and Reliable Signals 5.2 Equipment Operator Duties and Capacity Decisions 5.3 Lift Director, Qualified Rigger and Hazard Communication

6 Equipment Requirements and Lift Planning

6.1 Determine Equipment Requirements and Compatibility 6.2 Written Plans, Sequence and Change Control 6.3 Critical-Lift Criteria, Risk and Contingencies

7 Balanced Sling Forces

7.1 Two-Leg Tension and Angle Reference 7.2 Length-to-Height Geometry and Headroom 7.3 Horizontal Forces and Attachment Demand

8 Composite and Unequal Loads

8.1 Composite Center of Gravity by Moments 8.2 Off-Center Reactions and Compatible Sling Geometry 8.3 Three- and Four-Leg Assemblies and Load Sharing

9 Wire Rope, Chain and Metal Mesh Slings

9.1 Select and Use Wire-Rope Slings 9.2 Alloy-Chain Assemblies and Approved Adjustment 9.3 Metal-Mesh Slings: Selection, Contact and Removal

10 Synthetic Rope, Web and Roundslings

10.1 Synthetic-Rope Slings and Approved Splices 10.2 Synthetic-Web Slings and Material Compatibility 10.3 Roundslings, Core Protection and Performance Fibers

11 Hitch Application and Sling Protection

11.1 Vertical and Basket Hitch Capacity 11.2 Choker Hitches, Choke Angle and Bundles 11.3 Softeners, Bend Protection and Cut Protection

12 Shackles, Hooks and Collector Hardware

12.1 Shackle Types, Pin Seating and Side Loading 12.2 Hooks, Latches and Permitted Load Seating 12.3 Master Links, Rings and Swivels

13 Threaded Points and Adjustable Hardware

13.1 Eyebolts, Shoulder Seating and Angular Demand 13.2 Swivel Hoist Rings and Installation Torque 13.3 Turnbuckles and Chain Hardware in Adjustable Systems

14 Compression Hardware and Rigging Blocks

14.1 Wire-Rope Clips and Permitted Terminations 14.2 Wedge Sockets, Rope Alignment and Tail Security 14.3 Rigging Blocks, Resultants and Reeving

15 Manual, Lever and Powered Hoists

15.1 Manual Chain Falls and Vertical Hoisting 15.2 Lever Hoists, Pulling Direction and Controlled Adjustment 15.3 Air and Electric Hoists: Supply, Duty and Controls

16 Jacks, Rollers and Portable Supports

16.1 Jacks, Toe Ratings and Positive Support 16.2 Dollies, Skates, Rollers and Horizontal Control 16.3 A-Frames, Gantries and Trolley Compatibility

17 Structural Lifters and Clamps

17.1 Lifting Beams, Spreaders and Configuration Ratings 17.2 Plate Clamps, Material Limits and Grip Conditions 17.3 Beam Clamps as Attachments and Beam/Girder Lifters

18 Mechanical, Vacuum and Magnetic Devices

18.1 Mechanical and Vacuum Lifting Devices 18.2 Close-Proximity and Remotely Operated Lifting Magnets 18.3 Scrap and Material-Handling Grapples

19 Inspection, Removal and Records

19.1 Inspecting All Six Sling Families 19.2 Hook and Rigging-Hardware Inspection 19.3 Below-the-Hook Device Inspection and Testing

20 Lift Control, Rotation and Completion

20.1 Take-Up, Trial Lift and Load Control 20.2 Controlled Rotation, Upending and Multiple-Crane Lifts 20.3 Secure the Load, Remove Rigging and Stow Equipment

21 Technical Standards and Crane Capacity

21.1 Apply the Correct Standard and Regulatory Scope 21.2 Crane Charts, Suspended Weight and Capacity Deductions 21.3 Personnel Hoisting Under OSHA 1926.1431

7.1 Two-Leg Tension and Angle Reference

Key Takeaways Explain This Topic AI

For the defined model, tension is W divided by twice the sine of the horizontal angle.

Thirty degrees from vertical equals sixty degrees from horizontal.

At thirty degrees from horizontal, each leg tension equals W.

Last updated: October 2026

Separate vertical support from leg tension

For a symmetrical two-leg bridle , each leg provides half the vertical support when the load is balanced, the picks are at the same elevation and the geometry is symmetrical. The leg itself is inclined, so its tension is greater than that vertical component unless it is vertical. This distinction is central to sling and hardware selection.

Let the total supported load be W and each leg’s tension be T. Let θ be the angle between the sling and a horizontal reference through the picks. The vertical component of each tension is T sin θ. Summing both components gives W, so: T = W 2 sin ⁡ θ T=\frac{W}{2\sin\theta} T = 2 sin θ W ​

The load angle factor is 1/sin θ. It multiplies the vertical load share, not the total weight in every case. A factor greater than one means the sling has to carry a larger force to provide the required upward component.

Identify the angle before calculating

An angle measured from vertical is complementary to the horizontal angle in this simple model. If a sling is 30 degrees from vertical, it is 60 degrees from horizontal. Using sin 30 when the given 30-degree angle is vertical would produce a different and incorrect tension. Draw the reference line and label it before entering a factor.

  • Angle from horizontal Approximate angle factor Tension for a 20,000-lb balanced load
  • 90° 1.000 10,000 lb per vertical leg
  • 60° 1.1547 11,547 lb per leg
  • 45° 1.4142 14,142 lb per leg
  • 30° 2.000 20,000 lb per leg

At 30 degrees from horizontal, each leg’s tension equals the entire supported weight even though each supplies only half its vertical support. Adding the two tensions does not give the vertical weight; their components must be resolved in the correct directions.

For a simple numerical check, a 12,000-lb balanced load at 60 degrees needs approximately 6,000 × 1.1547 = 6,928 lb per leg . The two vertical components are each approximately 6,000 lb, totaling the weight. A proposed 6,000-lb vertical-rated sling is not adequate for that calculated leg tension merely because there are two slings.

Recognize the assumptions

The formula applies to the defined symmetrical model. An off-center CG, unequal pick elevations, different sling geometry or additional supports can invalidate equal division. A load that appears level is not necessarily symmetrical. Determine vertical reactions first when the CG is offset; then apply each leg’s own angle factor.

The supported weight for this model includes the masses carried below the two legs. A heavy lower beam or other carried gear can increase W. The crane block above those legs does not become part of their lower supported weight simply because it appears in crane capacity accounting. Trace the force path to decide which mass belongs in each calculation.

This is a static calculation. It does not approve shock loading or quantify all acceleration, wind and motion effects. The selected components and operating procedure must address those conditions separately. A design factor is not permission to add an unplanned bounce because the calculated tension appears below breaking strength.

Understand shallow angles

As the horizontal angle decreases, sine decreases and tension increases nonlinearly. The relationship is reciprocal-sine, not exponential. Small geometry changes at shallow angles can materially change demand and horizontal forces. Follow the manufacturer’s permitted minimum angle and the applicable standard or qualified-person conditions.

Do not cite OSHA 1926.251 as imposing a blanket engineer-signed prohibition at every angle below 30 degrees. The practical examination has its own 30-degree instruction, and sling standards and manufacturers have applicable angle conditions. The field selection must use the correct source for the actual assembly.

Selection example

A given sling is rated 8,000 lb for the applicable single-leg loading, and a balanced 12,000-lb load is proposed at 60 degrees. The calculated 6,928-lb tension is below that rating. This establishes only the tension comparison. The sling material, hitch, bend conditions, eye seating, attachments, temperature and movement controls must also be suitable.

If the same load is changed to 45 degrees, tension becomes approximately 6,000 × 1.4142 = 8,485 lb. The proposed sling no longer satisfies the numerical demand. The weight has not changed; the geometry has. The correct response is an approved change in component or arrangement, followed by the relevant checks, rather than relying on the unused breaking-strength margin.

Keep adequate precision during calculation, then choose equipment with applicable WLL at least equal to the demand. If an examination supplies a rounded factor, use its stated rounding consistently. Do not round a computed demand down simply to make it fit the available gear.

Use the provided calculator effectively

The on-screen four-function calculator can multiply a supplied angle factor by a vertical share. It does not require a trigonometric function when the factor is given. If a question supplies a factor of 1.414 for a balanced 10,000-lb load, first calculate 10,000/2 = 5,000 lb, then 5,000 × 1.414 = 7,070 lb. Record the factor's stated precision rather than claiming an exact trigonometric result.

Read a multi-leg assembly table differently from a single-leg rating. If the table already gives the complete two-leg assembly capacity at the stated angle, the manufacturer has incorporated that configuration. Do not apply the angle factor again to that assembly rating. Verify which quantity the table describes before comparing it with the supported weight.

Source: CCO rigging reference materials and capacity booklet .