Study guide

1.1 Current Exam, Eligibility and Scheduling

NCCCO Rigger Level II Exam

Track your progress as you read

Finished sections get a check mark.

1 Certification and Exam Preparation

1.1 Current Exam, Eligibility and Scheduling 1.2 Practical Tasks and Examination-Specific Rules 1.3 Study Method, References and Recertification

2 Identify and Measure the Load

2.1 Load Identity, Dimensions and Units 2.2 Load Weight, Density and Complete Inventories 2.3 Composition, Structural Integrity and Special Handling

3 Center of Gravity and Support Geometry

3.1 Center of Gravity and Suspended Stability 3.2 Attachment Points and Complete Force Paths 3.3 Final Position, Landing Supports and Derigging Access

4 Route and Site Hazards

4.1 Travel Path, Clearance and Work-Zone Control 4.2 Power Lines, Clearance Options and Electrical Response 4.3 Weather, Temperature and Ground Conditions

5 Team Duties and Communications

5.1 Signalperson Duties and Reliable Signals 5.2 Equipment Operator Duties and Capacity Decisions 5.3 Lift Director, Qualified Rigger and Hazard Communication

6 Equipment Requirements and Lift Planning

6.1 Determine Equipment Requirements and Compatibility 6.2 Written Plans, Sequence and Change Control 6.3 Critical-Lift Criteria, Risk and Contingencies

7 Balanced Sling Forces

7.1 Two-Leg Tension and Angle Reference 7.2 Length-to-Height Geometry and Headroom 7.3 Horizontal Forces and Attachment Demand

8 Composite and Unequal Loads

8.1 Composite Center of Gravity by Moments 8.2 Off-Center Reactions and Compatible Sling Geometry 8.3 Three- and Four-Leg Assemblies and Load Sharing

9 Wire Rope, Chain and Metal Mesh Slings

9.1 Select and Use Wire-Rope Slings 9.2 Alloy-Chain Assemblies and Approved Adjustment 9.3 Metal-Mesh Slings: Selection, Contact and Removal

10 Synthetic Rope, Web and Roundslings

10.1 Synthetic-Rope Slings and Approved Splices 10.2 Synthetic-Web Slings and Material Compatibility 10.3 Roundslings, Core Protection and Performance Fibers

11 Hitch Application and Sling Protection

11.1 Vertical and Basket Hitch Capacity 11.2 Choker Hitches, Choke Angle and Bundles 11.3 Softeners, Bend Protection and Cut Protection

12 Shackles, Hooks and Collector Hardware

12.1 Shackle Types, Pin Seating and Side Loading 12.2 Hooks, Latches and Permitted Load Seating 12.3 Master Links, Rings and Swivels

13 Threaded Points and Adjustable Hardware

13.1 Eyebolts, Shoulder Seating and Angular Demand 13.2 Swivel Hoist Rings and Installation Torque 13.3 Turnbuckles and Chain Hardware in Adjustable Systems

14 Compression Hardware and Rigging Blocks

14.1 Wire-Rope Clips and Permitted Terminations 14.2 Wedge Sockets, Rope Alignment and Tail Security 14.3 Rigging Blocks, Resultants and Reeving

15 Manual, Lever and Powered Hoists

15.1 Manual Chain Falls and Vertical Hoisting 15.2 Lever Hoists, Pulling Direction and Controlled Adjustment 15.3 Air and Electric Hoists: Supply, Duty and Controls

16 Jacks, Rollers and Portable Supports

16.1 Jacks, Toe Ratings and Positive Support 16.2 Dollies, Skates, Rollers and Horizontal Control 16.3 A-Frames, Gantries and Trolley Compatibility

17 Structural Lifters and Clamps

17.1 Lifting Beams, Spreaders and Configuration Ratings 17.2 Plate Clamps, Material Limits and Grip Conditions 17.3 Beam Clamps as Attachments and Beam/Girder Lifters

18 Mechanical, Vacuum and Magnetic Devices

18.1 Mechanical and Vacuum Lifting Devices 18.2 Close-Proximity and Remotely Operated Lifting Magnets 18.3 Scrap and Material-Handling Grapples

19 Inspection, Removal and Records

19.1 Inspecting All Six Sling Families 19.2 Hook and Rigging-Hardware Inspection 19.3 Below-the-Hook Device Inspection and Testing

20 Lift Control, Rotation and Completion

20.1 Take-Up, Trial Lift and Load Control 20.2 Controlled Rotation, Upending and Multiple-Crane Lifts 20.3 Secure the Load, Remove Rigging and Stow Equipment

21 Technical Standards and Crane Capacity

21.1 Apply the Correct Standard and Regulatory Scope 21.2 Crane Charts, Suspended Weight and Capacity Deductions 21.3 Personnel Hoisting Under OSHA 1926.1431

1.1 Current Exam, Eligibility and Scheduling

Key Takeaways Explain This Topic AI

The written examination has 50 questions in 60 minutes, averaging 72 seconds per question.

Level II permits the on-screen four-function calculator described in CCO’s written-testing instructions.

The corresponding written and practical examinations must be passed within 12 months.

A failed written exam requires reapplication, retest fees and a minimum four-week wait for the same exam.

Last updated: October 2026

What the credential measures

CCO Rigger Level II is the national rigging certification named in this guide. NCCCO is the National Commission for the Certification of Crane Operators, and CCO is the certification organization’s current public name. Level II includes determining load weight and center of gravity, selecting equipment for unfamiliar lifts, and applying rigging principles without supervision. A certificate establishes assessed competence; the employer must still determine whether a person is qualified for the particular equipment, load and task.

A Level II card does not by itself appoint its holder as a crane operator, signalperson, professional engineer or lift director. Those roles have their own responsibilities and qualification requirements. For example, calculating a two-leg sling tension is within the study scope; approving a damaged vessel lug for continued use requires authority and knowledge beyond identifying the lug as an attachment point.

The written examination has 50 multiple-choice questions in 60 minutes . This gives an average of 72 seconds per question, including review. The January 2025 Rigger Candidate Handbook identifies a calculator as permitted for Level II. CCO’s current written-testing instructions specify an on-screen basic four-function calculator for exams that permit one. Personal calculators, books, reference materials and scratch paper are not allowed in the examination room under those instructions. Do not plan around a personal scientific calculator or an unverified testing vendor’s rules.

The six domains

  • Domain Approximate share Preparation emphasis
  • Scope of the Rigging Activity 15% Understand the load, route, destination and hazards
  • Planning the Rigging Activity 15% Equipment requirements, roles and force calculations
  • Selection of Rigging Components 34% Six sling families, hardware, hoists and lifting devices
  • Technical Knowledge 13% Apply the named ASME standards and OSHA regulations
  • Inspection 10% Recognize damage and apply inspection programs
  • Execution of Rigging Activity 13% Assemble, operate, control, land and remove rigging

The weights are approximate blueprint percentages, not promises that a particular test form contains an exact whole-number count in each category. Equipment selection deserves the largest preparation allocation. Memorizing crane percentages while neglecting metal mesh, synthetic rope, trolleys or lifting magnets leaves major named topics unprepared.

Initial certification requirements

Candidates must be at least 18, comply with CCO’s substance-abuse policy and code of ethics, and pass the corresponding written and practical examinations. A valid Level II certification requires current Level I certification. Candidates may take Level I and Level II testing concurrently, but all Level I requirements must be satisfied before Level II certification becomes valid.

The corresponding written and practical examinations must be completed within 12 months of the first passed examination. This is a completion window, not an extension of an expired certification. Someone who passes a written exam and waits beyond that window cannot assume the result remains usable for an initial practical examination. Check the actual certification record and current handbook before selecting dates.

CCO lists three written delivery methods: Online Proctored Testing (OPT) , Test Center Testing (TCT) and Event Online Testing (EOT) . Applications and scheduling proceed through myCCO. Current written-testing instructions require application at least two business days before testing and allow six months from application to take approved exams. The application window and the 12-month certification-completion window are different clocks.

The listed CCO fee is $105 for the Rigger Level II written examination and $95 for the practical examination . Together those CCO fees are $200 for one initial Level II written/practical attempt. They do not include Level I testing, training, travel or additional practical-site charges. The fee page and the chosen site determine the actual amount to budget; an instructor’s bundled course price is not the CCO examination fee.

Scoring and retesting

CCO describes written examinations as criterion referenced : a standard is established before testing rather than ranking candidates against one another. The current handbook and written-testing instructions reviewed here do not publish a numerical Level II passing cut score. Therefore, do not translate an unsupported “70%” into a required number of correct answers. Practice percentages are useful study diagnostics, but they do not establish the official passing standard.

Preliminary written results are available immediately after testing, with results also available through myCCO and email. Candidates who fail must reapply and pay the corresponding retest fees. CCO’s current instructions require a minimum four-week wait before retaking the same written examination . Practical retest arrangements follow the practical procedures and site availability; a written waiting period should not be invented for every practical circumstance.

Scheduling example

A candidate already holds current Level I certification and passes the Level II written exam in November. Before paying a practical-site fee, the candidate checks the written pass date, the site’s approved Level II course, available practical dates and additional site charges. The practical must fall within the corresponding 12-month completion window. If a written retest is necessary, a date only ten days after failure would conflict with the four-week rule.

Keep the handbook, fee page and testing instructions together when planning. A course advertisement may describe training duration accurately while giving outdated examination counts. The source controlling an exam policy is CCO’s current program guidance, not the quantity of questions in a third-party practice bank.

Sources: Rigger handbook , written testing , exam fees .