Study guide
12.2 Hooks, Latches and Permitted Load Seating
NCCCO Rigger Level II Exam
Track your progress as you read
Finished sections get a check mark.
1 Certification and Exam Preparation
1.1 Current Exam, Eligibility and Scheduling 1.2 Practical Tasks and Examination-Specific Rules 1.3 Study Method, References and Recertification
2 Identify and Measure the Load
2.1 Load Identity, Dimensions and Units 2.2 Load Weight, Density and Complete Inventories 2.3 Composition, Structural Integrity and Special Handling
3 Center of Gravity and Support Geometry
3.1 Center of Gravity and Suspended Stability 3.2 Attachment Points and Complete Force Paths 3.3 Final Position, Landing Supports and Derigging Access
4 Route and Site Hazards
4.1 Travel Path, Clearance and Work-Zone Control 4.2 Power Lines, Clearance Options and Electrical Response 4.3 Weather, Temperature and Ground Conditions
5 Team Duties and Communications
5.1 Signalperson Duties and Reliable Signals 5.2 Equipment Operator Duties and Capacity Decisions 5.3 Lift Director, Qualified Rigger and Hazard Communication
6 Equipment Requirements and Lift Planning
6.1 Determine Equipment Requirements and Compatibility 6.2 Written Plans, Sequence and Change Control 6.3 Critical-Lift Criteria, Risk and Contingencies
7 Balanced Sling Forces
7.1 Two-Leg Tension and Angle Reference 7.2 Length-to-Height Geometry and Headroom 7.3 Horizontal Forces and Attachment Demand
8 Composite and Unequal Loads
8.1 Composite Center of Gravity by Moments 8.2 Off-Center Reactions and Compatible Sling Geometry 8.3 Three- and Four-Leg Assemblies and Load Sharing
9 Wire Rope, Chain and Metal Mesh Slings
9.1 Select and Use Wire-Rope Slings 9.2 Alloy-Chain Assemblies and Approved Adjustment 9.3 Metal-Mesh Slings: Selection, Contact and Removal
10 Synthetic Rope, Web and Roundslings
10.1 Synthetic-Rope Slings and Approved Splices 10.2 Synthetic-Web Slings and Material Compatibility 10.3 Roundslings, Core Protection and Performance Fibers
11 Hitch Application and Sling Protection
11.1 Vertical and Basket Hitch Capacity 11.2 Choker Hitches, Choke Angle and Bundles 11.3 Softeners, Bend Protection and Cut Protection
12 Shackles, Hooks and Collector Hardware
12.1 Shackle Types, Pin Seating and Side Loading 12.2 Hooks, Latches and Permitted Load Seating 12.3 Master Links, Rings and Swivels
13 Threaded Points and Adjustable Hardware
13.1 Eyebolts, Shoulder Seating and Angular Demand 13.2 Swivel Hoist Rings and Installation Torque 13.3 Turnbuckles and Chain Hardware in Adjustable Systems
14 Compression Hardware and Rigging Blocks
14.1 Wire-Rope Clips and Permitted Terminations 14.2 Wedge Sockets, Rope Alignment and Tail Security 14.3 Rigging Blocks, Resultants and Reeving
15 Manual, Lever and Powered Hoists
15.1 Manual Chain Falls and Vertical Hoisting 15.2 Lever Hoists, Pulling Direction and Controlled Adjustment 15.3 Air and Electric Hoists: Supply, Duty and Controls
16 Jacks, Rollers and Portable Supports
16.1 Jacks, Toe Ratings and Positive Support 16.2 Dollies, Skates, Rollers and Horizontal Control 16.3 A-Frames, Gantries and Trolley Compatibility
17 Structural Lifters and Clamps
17.1 Lifting Beams, Spreaders and Configuration Ratings 17.2 Plate Clamps, Material Limits and Grip Conditions 17.3 Beam Clamps as Attachments and Beam/Girder Lifters
18 Mechanical, Vacuum and Magnetic Devices
18.1 Mechanical and Vacuum Lifting Devices 18.2 Close-Proximity and Remotely Operated Lifting Magnets 18.3 Scrap and Material-Handling Grapples
19 Inspection, Removal and Records
19.1 Inspecting All Six Sling Families 19.2 Hook and Rigging-Hardware Inspection 19.3 Below-the-Hook Device Inspection and Testing
20 Lift Control, Rotation and Completion
20.1 Take-Up, Trial Lift and Load Control 20.2 Controlled Rotation, Upending and Multiple-Crane Lifts 20.3 Secure the Load, Remove Rigging and Stow Equipment
21 Technical Standards and Crane Capacity
21.1 Apply the Correct Standard and Regulatory Scope 21.2 Crane Charts, Suspended Weight and Capacity Deductions 21.3 Personnel Hoisting Under OSHA 1926.1431
12.2 Hooks, Latches and Permitted Load Seating
Key Takeaways Explain This Topic AI
Avoid tip, back and side loading unless explicitly designed for the application.
A latch does not carry payload weight.
Not every swivel hook is approved to rotate under load.
Last updated: October 2026
Put the load in the intended bowl
A hook transmits load through its body, normally with the connection seated in the base or bowl. Its rated load depends on its type, installation and permitted loading. The tip, back and latch are not interchangeable load-bearing locations. A hook that can admit an eye does not necessarily support it in the correct position.
The CCO reference manual’s B30.10 excerpt instructs centering load in the bowl and avoiding tip, side and back loading. It also addresses multi-leg angles and collector hardware. Use the manufacturer’s limits for the actual hook. A broad included angle can spread eyes toward the tip or create side forces even when the combined weight is below the marked WLL.
For the excerpt’s single-point-hook guidance, the maximum included angle between legs in the bowl is 90 degrees unless the hook manufacturer determines otherwise, and collector hardware is advised for more than two legs or larger leg angles. This is a specific hook-loading instruction, not a general rating formula for every sling assembly.
Latches retain slack connections
A latch helps retain a loose sling or attachment when the system is slack. It is not intended to carry the load. The presence of a latch does not eliminate the need to verify engagement before tension and during operation. An eye riding on the latch can overload a part that has no payload-carrying function.
The need for a latch or approved mousing depends on the application and applicable instructions. It is incorrect to state that every material-handling hook must universally have the same spring latch. Personnel hoisting has specific positive-closure requirements. Where a latch is required, an inoperative latch must be resolved through the permitted repair, replacement or approved interim method before use.
- Hook condition Required interpretation
- Eye in bowl Verify fit and centered bearing
- Eye on tip Unapproved point loading
- Load on latch Latch is being misused as a load-bearing part
- Self-locking hook Locking mechanism must function and be locked in use
- Swiveling connection Check whether rotation under load is actually permitted
Do not improvise a latch substitute with tape or an arbitrary zip tie. Follow the manufacturer and qualified-person provisions for any approved mousing. A field expedient that merely closes the visible opening does not prove adequate retention.
Rotation capability is product specific
A hook with a swivel connection may be designed to align before loading, or may have a bearing intended for rotation under specified load. Not every swiveling hook can rotate freely under load. Consult the actual product instructions. Forcing rotation through a nonbearing connection can introduce torsion or damage.
Likewise, sister or duplex hooks and multi-prong hooks have specific balancing and loading instructions. The reference excerpt addresses equal loading of both duplex saddles unless designed otherwise. Do not use one prong as if it always carries the full combined rating. A pinhole or special attachment has its own capacity conditions.
Inspection is based on the original geometry
Under the B30.10 excerpt in the CCO reference manual, visible bend or twist, significant wear, cracks, and throat distortion require action through the specified repair/replacement process. Its throat criterion addresses an increase of 5%, not to exceed 1/4 inch, or the manufacturer recommendation. A modern product’s instructions or applicable edition can govern the precise condition, so use the identified baseline and rule.
For a training original opening of 4 inches, 5% is 0.20 inch, smaller than 0.25 inch. An observed opening of 4.25 inches exceeds that criterion. It is unsafe to use the larger quarter-inch value simply because the original hook is large enough to measure it.
The excerpt identifies wear exceeding 10% of the original sectional dimension or the manufacturer’s recommendation. Do not extend that number into a universal wear allowance for every associated pin, latch or component. A crack or deformation can require removal even when measured thickness remains high.
Repairs need authority
Manufacturer or qualified-person approval governs repairs and modifications in the reference excerpt. It does not authorize every rigger to grind a crack out or heat a bent hook straight. Remove suspect hooks from service and use the applicable assessment and approved repair process. Heating, welding or uncontrolled alteration can change material properties and geometry.
Hook-fit scenario
A sling eye is too small to reach the bowl and rests across the tip. The hook’s marked capacity exceeds the payload weight, but the connection is still unsuitable. Choose a compatible hook, eye or approved collector arrangement. Pulling hard until the eye stretches into place damages the sling and does not establish correct bearing.
Before lifting, check that the hook can align, the eye is seated, the latch or lock functions where required, and personnel are clear of the closing connection. After release, prevent the hook and attached gear from swinging into people or structures. Correct seating is required every time, not just during initial assembly.
Source: CCO Rigger Reference Manual, B30.10 excerpt .