Study guide

12.3 Master Links, Rings and Swivels

NCCCO Rigger Level II Exam

Track your progress as you read

Finished sections get a check mark.

1 Certification and Exam Preparation

1.1 Current Exam, Eligibility and Scheduling 1.2 Practical Tasks and Examination-Specific Rules 1.3 Study Method, References and Recertification

2 Identify and Measure the Load

2.1 Load Identity, Dimensions and Units 2.2 Load Weight, Density and Complete Inventories 2.3 Composition, Structural Integrity and Special Handling

3 Center of Gravity and Support Geometry

3.1 Center of Gravity and Suspended Stability 3.2 Attachment Points and Complete Force Paths 3.3 Final Position, Landing Supports and Derigging Access

4 Route and Site Hazards

4.1 Travel Path, Clearance and Work-Zone Control 4.2 Power Lines, Clearance Options and Electrical Response 4.3 Weather, Temperature and Ground Conditions

5 Team Duties and Communications

5.1 Signalperson Duties and Reliable Signals 5.2 Equipment Operator Duties and Capacity Decisions 5.3 Lift Director, Qualified Rigger and Hazard Communication

6 Equipment Requirements and Lift Planning

6.1 Determine Equipment Requirements and Compatibility 6.2 Written Plans, Sequence and Change Control 6.3 Critical-Lift Criteria, Risk and Contingencies

7 Balanced Sling Forces

7.1 Two-Leg Tension and Angle Reference 7.2 Length-to-Height Geometry and Headroom 7.3 Horizontal Forces and Attachment Demand

8 Composite and Unequal Loads

8.1 Composite Center of Gravity by Moments 8.2 Off-Center Reactions and Compatible Sling Geometry 8.3 Three- and Four-Leg Assemblies and Load Sharing

9 Wire Rope, Chain and Metal Mesh Slings

9.1 Select and Use Wire-Rope Slings 9.2 Alloy-Chain Assemblies and Approved Adjustment 9.3 Metal-Mesh Slings: Selection, Contact and Removal

10 Synthetic Rope, Web and Roundslings

10.1 Synthetic-Rope Slings and Approved Splices 10.2 Synthetic-Web Slings and Material Compatibility 10.3 Roundslings, Core Protection and Performance Fibers

11 Hitch Application and Sling Protection

11.1 Vertical and Basket Hitch Capacity 11.2 Choker Hitches, Choke Angle and Bundles 11.3 Softeners, Bend Protection and Cut Protection

12 Shackles, Hooks and Collector Hardware

12.1 Shackle Types, Pin Seating and Side Loading 12.2 Hooks, Latches and Permitted Load Seating 12.3 Master Links, Rings and Swivels

13 Threaded Points and Adjustable Hardware

13.1 Eyebolts, Shoulder Seating and Angular Demand 13.2 Swivel Hoist Rings and Installation Torque 13.3 Turnbuckles and Chain Hardware in Adjustable Systems

14 Compression Hardware and Rigging Blocks

14.1 Wire-Rope Clips and Permitted Terminations 14.2 Wedge Sockets, Rope Alignment and Tail Security 14.3 Rigging Blocks, Resultants and Reeving

15 Manual, Lever and Powered Hoists

15.1 Manual Chain Falls and Vertical Hoisting 15.2 Lever Hoists, Pulling Direction and Controlled Adjustment 15.3 Air and Electric Hoists: Supply, Duty and Controls

16 Jacks, Rollers and Portable Supports

16.1 Jacks, Toe Ratings and Positive Support 16.2 Dollies, Skates, Rollers and Horizontal Control 16.3 A-Frames, Gantries and Trolley Compatibility

17 Structural Lifters and Clamps

17.1 Lifting Beams, Spreaders and Configuration Ratings 17.2 Plate Clamps, Material Limits and Grip Conditions 17.3 Beam Clamps as Attachments and Beam/Girder Lifters

18 Mechanical, Vacuum and Magnetic Devices

18.1 Mechanical and Vacuum Lifting Devices 18.2 Close-Proximity and Remotely Operated Lifting Magnets 18.3 Scrap and Material-Handling Grapples

19 Inspection, Removal and Records

19.1 Inspecting All Six Sling Families 19.2 Hook and Rigging-Hardware Inspection 19.3 Below-the-Hook Device Inspection and Testing

20 Lift Control, Rotation and Completion

20.1 Take-Up, Trial Lift and Load Control 20.2 Controlled Rotation, Upending and Multiple-Crane Lifts 20.3 Secure the Load, Remove Rigging and Stow Equipment

21 Technical Standards and Crane Capacity

21.1 Apply the Correct Standard and Regulatory Scope 21.2 Crane Charts, Suspended Weight and Capacity Deductions 21.3 Personnel Hoisting Under OSHA 1926.1431

12.3 Master Links, Rings and Swivels

Key Takeaways Explain This Topic AI

Master-link capacity and hook fit are separate checks.

Intermediate links organize connections but do not inherently equalize legs.

Under-load swivel use requires explicit product approval.

Last updated: October 2026

Collect forces without crowding

Links and rings connect rigging components or collect several sling legs into a common upper connection. A master link receives the assembly’s combined load and must fit the hook and lower components. Its opening and bearing geometry matter independently of its tensile rating.

A link too small for the hook can ride toward the tip, wedge against the shank or prevent the hook’s latch from closing. A link large enough to admit many eyes can still create crowding, crossed loads or bending if the eyes do not seat correctly. Select the rated collector arrangement specified for the assembly rather than forcing all connections into the nearest ring.

Master-link subassemblies use intermediate links to organize multiple legs and provide room for proper bearing. They are common in three- or four-leg systems, but no universal rule requires one identical arrangement for every sling assembly. The manufacturer’s approved construction and rating control. Intermediate links do not automatically equalize lower-leg forces.

Identify the rating basis

A link can carry different arrangements with different capacity conditions. The sling material, number of legs, included angles and connected hardware influence its application. A manufacturer may rate a master link as part of a particular chain assembly rather than give an unrestricted capacity for any collection of components.

  • Collector check Purpose
  • Manufacturer and rating Establishes the actual product and allowable use
  • Upper hook fit Keeps load in the bowl with proper bearing
  • Lower component fit Avoids crowding, crossing and binding
  • Included angles Keeps forces within rated conditions
  • Complete assembly demand Includes everything the collector carries

The master link may carry payload plus lower rigging and a lifting device. An individual leg connection carries its own tension. Do not assume both demands are numerically identical. Trace the masses and forces through each level of the assembly.

Use compatible connectors

Connecting links for chain often have specific locking, pin or bushing arrangements. Install the correct components in the specified sequence. A connector that appears closed may still be incomplete if its locking pin is not fully installed. Do not replace parts with bolts, wire or a different manufacturer’s piece without approval.

Some connectors are intended for chain, some for textile slings, and some for wire-rope eyes. Contact width and bend geometry can limit the use of a steel fitting with a textile sling. The fitting’s WLL alone does not prove that it will not pinch or cut the sling.

Avoid joining eyes by an unapproved improvised arrangement. The resulting bend and contact can be different from either sling’s rated condition. Use appropriate rated hardware with the manufacturer’s specified geometry and capacity.

Swivels manage alignment only as designed

A swivel permits relative rotation in a connection under its specified conditions. Some products are intended for alignment without load; others use bearings designed for rotation under load. Read the actual product instructions. A swiveling appearance does not establish under-load rotation permission.

A swivel also interacts with rope construction. Certain rope systems restrict swivels because rotation can affect strand balance or core behavior. The rope and equipment manufacturer instructions must agree with the proposed connection. Do not insert a swivel simply because a load tends to spin.

An under-load swivel does not eliminate the need to control payload rotation. Wind, asymmetric contact or rope torque can still create movement. The handling plan must provide appropriate orientation control and safe personnel positions.

Demand example

A master link collects two legs carrying a 20,000-lb payload and 800 lb of lower device and rigging weight. In the simplified static model, its vertical resultant demand is 20,800 lb. Each inclined lower leg can have a tension that is greater than half that total. Selecting a master link based on one leg’s reaction or selecting each leg based on the master link’s vertical load would confuse the force paths.

Inspect and maintain the connection

Check markings, wear, cracks, deformation, corrosion, heat damage and locking parts under applicable B30.26 and manufacturer criteria. A distorted ring can impose unintended bearing even if its remaining cross section appears large. Missing pins or incomplete locks require removal from use until properly resolved.

Do not heat, weld or bend a link to change fit. Altering its geometry can change strength and invalidate the assembly rating. A component that does not fit should prompt compatible selection, not field reshaping.

During take-up, verify the collected legs settle into their intended positions. Do not reach into a closing collector to straighten a crossed eye while force develops. Stop and unload through the planned process before correcting the arrangement. After use, keep related components identifiable and prevent loose connectors from being mistaken for approved substitutes.

The exam trap is treating a collector as a magic capacity multiplier. It organizes and transmits forces; it does not create additional sling strength or guarantee equal lower-leg loading. Capacity and geometry must be checked at every interface.

Sources: CCO B30.26 and reference booklet resources , Crosby connector information .