Study guide
12.1 Shackle Types, Pin Seating and Side Loading
NCCCO Rigger Level II Exam
Track your progress as you read
Finished sections get a check mark.
1 Certification and Exam Preparation
1.1 Current Exam, Eligibility and Scheduling 1.2 Practical Tasks and Examination-Specific Rules 1.3 Study Method, References and Recertification
2 Identify and Measure the Load
2.1 Load Identity, Dimensions and Units 2.2 Load Weight, Density and Complete Inventories 2.3 Composition, Structural Integrity and Special Handling
3 Center of Gravity and Support Geometry
3.1 Center of Gravity and Suspended Stability 3.2 Attachment Points and Complete Force Paths 3.3 Final Position, Landing Supports and Derigging Access
4 Route and Site Hazards
4.1 Travel Path, Clearance and Work-Zone Control 4.2 Power Lines, Clearance Options and Electrical Response 4.3 Weather, Temperature and Ground Conditions
5 Team Duties and Communications
5.1 Signalperson Duties and Reliable Signals 5.2 Equipment Operator Duties and Capacity Decisions 5.3 Lift Director, Qualified Rigger and Hazard Communication
6 Equipment Requirements and Lift Planning
6.1 Determine Equipment Requirements and Compatibility 6.2 Written Plans, Sequence and Change Control 6.3 Critical-Lift Criteria, Risk and Contingencies
7 Balanced Sling Forces
7.1 Two-Leg Tension and Angle Reference 7.2 Length-to-Height Geometry and Headroom 7.3 Horizontal Forces and Attachment Demand
8 Composite and Unequal Loads
8.1 Composite Center of Gravity by Moments 8.2 Off-Center Reactions and Compatible Sling Geometry 8.3 Three- and Four-Leg Assemblies and Load Sharing
9 Wire Rope, Chain and Metal Mesh Slings
9.1 Select and Use Wire-Rope Slings 9.2 Alloy-Chain Assemblies and Approved Adjustment 9.3 Metal-Mesh Slings: Selection, Contact and Removal
10 Synthetic Rope, Web and Roundslings
10.1 Synthetic-Rope Slings and Approved Splices 10.2 Synthetic-Web Slings and Material Compatibility 10.3 Roundslings, Core Protection and Performance Fibers
11 Hitch Application and Sling Protection
11.1 Vertical and Basket Hitch Capacity 11.2 Choker Hitches, Choke Angle and Bundles 11.3 Softeners, Bend Protection and Cut Protection
12 Shackles, Hooks and Collector Hardware
12.1 Shackle Types, Pin Seating and Side Loading 12.2 Hooks, Latches and Permitted Load Seating 12.3 Master Links, Rings and Swivels
13 Threaded Points and Adjustable Hardware
13.1 Eyebolts, Shoulder Seating and Angular Demand 13.2 Swivel Hoist Rings and Installation Torque 13.3 Turnbuckles and Chain Hardware in Adjustable Systems
14 Compression Hardware and Rigging Blocks
14.1 Wire-Rope Clips and Permitted Terminations 14.2 Wedge Sockets, Rope Alignment and Tail Security 14.3 Rigging Blocks, Resultants and Reeving
15 Manual, Lever and Powered Hoists
15.1 Manual Chain Falls and Vertical Hoisting 15.2 Lever Hoists, Pulling Direction and Controlled Adjustment 15.3 Air and Electric Hoists: Supply, Duty and Controls
16 Jacks, Rollers and Portable Supports
16.1 Jacks, Toe Ratings and Positive Support 16.2 Dollies, Skates, Rollers and Horizontal Control 16.3 A-Frames, Gantries and Trolley Compatibility
17 Structural Lifters and Clamps
17.1 Lifting Beams, Spreaders and Configuration Ratings 17.2 Plate Clamps, Material Limits and Grip Conditions 17.3 Beam Clamps as Attachments and Beam/Girder Lifters
18 Mechanical, Vacuum and Magnetic Devices
18.1 Mechanical and Vacuum Lifting Devices 18.2 Close-Proximity and Remotely Operated Lifting Magnets 18.3 Scrap and Material-Handling Grapples
19 Inspection, Removal and Records
19.1 Inspecting All Six Sling Families 19.2 Hook and Rigging-Hardware Inspection 19.3 Below-the-Hook Device Inspection and Testing
20 Lift Control, Rotation and Completion
20.1 Take-Up, Trial Lift and Load Control 20.2 Controlled Rotation, Upending and Multiple-Crane Lifts 20.3 Secure the Load, Remove Rigging and Stow Equipment
21 Technical Standards and Crane Capacity
21.1 Apply the Correct Standard and Regulatory Scope 21.2 Crane Charts, Suspended Weight and Capacity Deductions 21.3 Personnel Hoisting Under OSHA 1926.1431
12.1 Shackle Types, Pin Seating and Side Loading
Key Takeaways Explain This Topic AI
Fully seat the screw pin as instructed; do not apply a quarter-turn back-off rule.
Use matching approved pins and required bolt-type retainers.
A sliding load can rotate a screw pin and requires an approved arrangement.
Last updated: October 2026
Match body, pin and application
A shackle connects rigging through a body and its matching pin. Anchor or bow shackles provide a wider curved region, while chain or D shackles have a narrower shape. Select the identified product for capacity, fit and loading direction. The body and pin form a rated assembly; an arbitrary pin or commercial bolt is not an approved replacement.
Screw-pin shackles can suit permitted pick-and-place applications. Install the pin according to the manufacturer, fully seated with its shoulder against the ear as specified. Do not back it off a quarter turn or any fraction of a turn as a general rigging rule. Pin seating and the required securement must be maintained before lifting.
Bolt-type shackles use the correct bolt, nut and retaining pin. They can suit approved longer-term arrangements or conditions where movement might rotate a screw pin. Use all required parts, including the proper cotter or other retainer. A wire substituted for a missing nut or pin does not preserve the specified assembly.
Fit the connection without binding
Check the lug-hole and pin dimensions, the body’s clearance, bearing contact and articulation. A pin that fits through the hole may still leave the body wedged against a flange. Hardware must align with the applied force through the planned movement. Select a compatible connection or redesign the pick rather than grinding the body or drilling the lug without approval.
The intended loading orientation depends on the product and arrangement. Common two-sling collection arrangements place the sling eyes in the bow and the load connection at the pin, subject to manufacturer instructions and included-angle conditions. Do not turn this into a rule permitting unlimited eyes, crowding or any angle. The actual parts must seat without crossing or binding.
- Shackle check Unsafe assumption to avoid
- Matching body and pin Any bolt of similar diameter will work
- Pin shoulder fully seated Backing off prevents all problems
- Required retainers The nut alone makes every bolt-type assembly complete
- Lug and bow clearance Passing through the hole proves alignment
- Permitted loading direction Every shackle has identical side-load permission
- Prevent pin rotation in sliding arrangements
A load sliding across a screw pin can rotate and loosen it. Manufacturer instructions may prohibit that application and specify bolt-type hardware or another arrangement. Evaluate actual relative movement, including during a choker tightening or a load turn. A screw pin that was secure at installation can be exposed to a different contact path mid-operation.
Do not use improvised mousing as permission to violate an application prohibition. Securement must follow the product instructions. If the selected shackle cannot be used in the proposed movement, select a compatible rated alternative.
Apply side-load information to the actual product
Side loading applies force outside the intended central loading plane and can reduce capacity. Some manufacturers provide reductions for certain shackle models and sizes; others prohibit the proposed condition. There is no universal interval table stating that every angle from 1 through 45 degrees gives the same percentage.
For an exercise, assume the specified manufacturer allows a particular shackle at 45 degrees with 70% of its in-line WLL . If the in-line WLL is 20,000 lb, the applicable side-load rating is 14,000 lb. A 15,000-lb resultant exceeds it. These supplied values apply only to the described product and approved side-load condition.
Angle, multi-leg included angle and out-of-plane side loading are different descriptions. Read the drawing to identify what the table measures. A broad bow admitting two sling eyes does not automatically allow force across the ears in any direction.
Inspect the body and pin
Check identification, cracks, wear, deformation, corrosion, heat damage, thread condition and missing parts under the manufacturer and applicable B30.26 criteria. A bent pin or distorted body requires removal/evaluation. There is no safe universal ten-degree bending allowance for shackles.
A pin must thread properly and seat as instructed. Cross-threading, damaged threads or a shoulder unable to seat are not corrected by additional wrench force. Do not replace a lost pin with a Grade 8 bolt or swap pins across sizes and manufacturers. Obtain the matching approved part and evaluate the assembly’s condition.
Application scenario
A crew uses an adequately rated screw-pin shackle in a choke where the sling will slide over its pin during rotation. The WLL comparison does not address the loosening hazard. Review the manufacturer’s prohibited and permitted uses and choose an approved retained connection. The safe response is a configuration change, not intentionally loosening the pin to make it rotate more easily.
After unloading, remove shackles without uncontrolled dropping, clean as instructed and store matching pins with their bodies. Preserve identification and separate removed gear so it cannot be returned to use by appearance alone.
Sources: CCO rigging hardware reference material , Crosby shackles and application information .