Study guide

16.3 A-Frames, Gantries and Trolley Compatibility

NCCCO Rigger Level II Exam

Track your progress as you read

Finished sections get a check mark.

1 Certification and Exam Preparation

1.1 Current Exam, Eligibility and Scheduling 1.2 Practical Tasks and Examination-Specific Rules 1.3 Study Method, References and Recertification

2 Identify and Measure the Load

2.1 Load Identity, Dimensions and Units 2.2 Load Weight, Density and Complete Inventories 2.3 Composition, Structural Integrity and Special Handling

3 Center of Gravity and Support Geometry

3.1 Center of Gravity and Suspended Stability 3.2 Attachment Points and Complete Force Paths 3.3 Final Position, Landing Supports and Derigging Access

4 Route and Site Hazards

4.1 Travel Path, Clearance and Work-Zone Control 4.2 Power Lines, Clearance Options and Electrical Response 4.3 Weather, Temperature and Ground Conditions

5 Team Duties and Communications

5.1 Signalperson Duties and Reliable Signals 5.2 Equipment Operator Duties and Capacity Decisions 5.3 Lift Director, Qualified Rigger and Hazard Communication

6 Equipment Requirements and Lift Planning

6.1 Determine Equipment Requirements and Compatibility 6.2 Written Plans, Sequence and Change Control 6.3 Critical-Lift Criteria, Risk and Contingencies

7 Balanced Sling Forces

7.1 Two-Leg Tension and Angle Reference 7.2 Length-to-Height Geometry and Headroom 7.3 Horizontal Forces and Attachment Demand

8 Composite and Unequal Loads

8.1 Composite Center of Gravity by Moments 8.2 Off-Center Reactions and Compatible Sling Geometry 8.3 Three- and Four-Leg Assemblies and Load Sharing

9 Wire Rope, Chain and Metal Mesh Slings

9.1 Select and Use Wire-Rope Slings 9.2 Alloy-Chain Assemblies and Approved Adjustment 9.3 Metal-Mesh Slings: Selection, Contact and Removal

10 Synthetic Rope, Web and Roundslings

10.1 Synthetic-Rope Slings and Approved Splices 10.2 Synthetic-Web Slings and Material Compatibility 10.3 Roundslings, Core Protection and Performance Fibers

11 Hitch Application and Sling Protection

11.1 Vertical and Basket Hitch Capacity 11.2 Choker Hitches, Choke Angle and Bundles 11.3 Softeners, Bend Protection and Cut Protection

12 Shackles, Hooks and Collector Hardware

12.1 Shackle Types, Pin Seating and Side Loading 12.2 Hooks, Latches and Permitted Load Seating 12.3 Master Links, Rings and Swivels

13 Threaded Points and Adjustable Hardware

13.1 Eyebolts, Shoulder Seating and Angular Demand 13.2 Swivel Hoist Rings and Installation Torque 13.3 Turnbuckles and Chain Hardware in Adjustable Systems

14 Compression Hardware and Rigging Blocks

14.1 Wire-Rope Clips and Permitted Terminations 14.2 Wedge Sockets, Rope Alignment and Tail Security 14.3 Rigging Blocks, Resultants and Reeving

15 Manual, Lever and Powered Hoists

15.1 Manual Chain Falls and Vertical Hoisting 15.2 Lever Hoists, Pulling Direction and Controlled Adjustment 15.3 Air and Electric Hoists: Supply, Duty and Controls

16 Jacks, Rollers and Portable Supports

16.1 Jacks, Toe Ratings and Positive Support 16.2 Dollies, Skates, Rollers and Horizontal Control 16.3 A-Frames, Gantries and Trolley Compatibility

17 Structural Lifters and Clamps

17.1 Lifting Beams, Spreaders and Configuration Ratings 17.2 Plate Clamps, Material Limits and Grip Conditions 17.3 Beam Clamps as Attachments and Beam/Girder Lifters

18 Mechanical, Vacuum and Magnetic Devices

18.1 Mechanical and Vacuum Lifting Devices 18.2 Close-Proximity and Remotely Operated Lifting Magnets 18.3 Scrap and Material-Handling Grapples

19 Inspection, Removal and Records

19.1 Inspecting All Six Sling Families 19.2 Hook and Rigging-Hardware Inspection 19.3 Below-the-Hook Device Inspection and Testing

20 Lift Control, Rotation and Completion

20.1 Take-Up, Trial Lift and Load Control 20.2 Controlled Rotation, Upending and Multiple-Crane Lifts 20.3 Secure the Load, Remove Rigging and Stow Equipment

21 Technical Standards and Crane Capacity

21.1 Apply the Correct Standard and Regulatory Scope 21.2 Crane Charts, Suspended Weight and Capacity Deductions 21.3 Personnel Hoisting Under OSHA 1926.1431

16.3 A-Frames, Gantries and Trolley Compatibility

Key Takeaways Explain This Topic AI

A trolley rating does not approve its supporting beam.

Include relevant hoist deadweight in carried-load accounting.

Loaded movement of a portable frame requires explicit product permission.

Last updated: October 2026

A portable support remains a rated structure

An A-frame uses an approved frame arrangement to support lifting equipment or a handled load. Portable gantries and other framed supports have related applications but different designs. Their capacity depends on the actual height, span, support, bracing and manufacturer conditions. A triangular appearance does not establish a lifting rating.

Identify the exact product and permitted configuration. Adjustable legs or beams may have different ratings at different positions. Required braces, pins, bolts, wheels and locks are structural parts, not optional accessories. A frame with one missing brace cannot be rated from the complete product’s nameplate.

A trolley carries a hoist or connection along a suitable beam. Plain, geared and powered trolleys have different control and travel characteristics. The beam, trolley, hoist and connections form a system; each must suit the imposed demand and the others’ geometry.

Match wheels and beam dimensions

Trolleys are specified for beam flange widths, thicknesses, profiles and sometimes curve radii. Adjust wheel spacing through the manufacturer procedure, using the specified spacers and retaining parts. Physical placement over a flange does not prove correct wheel engagement.

Check that the beam has adequate structural capacity and support for trolley travel. Its reaction can move along the span, changing support loads and bending. A rated trolley does not approve an ordinary building beam or an unverified portable support.

  • Support-system item Check
  • Frame height and span Use the actual configuration rating
  • Braces and pins Complete structural assembly
  • Beam Capacity, profile and supporting structure
  • Trolley Rated load, flange fit and permitted travel
  • Hoist Capacity, deadweight and suspension compatibility
  • Stops and controls Prevent unplanned travel or departure

The trolley’s carried demand includes the hoist and lower suspended equipment where the rating definition requires it. A 5,000-lb payload plus a 500-lb hoist cannot be assumed to fit a trolley rated 5,000 lb for total carried load. Trace the correct inventory.

Travel restrictions are product specific

Some portable gantries may permit movement while loaded under specified conditions; others require unloading before movement. Do not state that every wheeled frame can be rolled under load or that every product prohibits it. Follow the actual instructions for floor, orientation, speed, load position and wheel locking.

A frame can overturn if force acts outside its approved support condition. Side pulling, sudden trolley stops, slope or a high suspended load can introduce instability. Do not use the frame to drag a load sideways unless expressly designed and approved for that task.

End stops, travel limits and other restraints must be installed as specified. Their presence is not permission to strike them at operating speed. Plan stopping points and controlled movement so the system stays within its designed range.

Assembly and inspection

Assemble through the manufacturer’s sequence with appropriate lifting and access methods. Protect people from unsupported members during setup. Verify pins fully engage, retainers are installed, fasteners meet requirements and braces are correctly placed. A partially assembled frame must not be loaded to “help it settle.”

Inspect structural members, welds, holes, pins, wheels, beam surfaces, trolley mechanisms and identification. Wear, deformation, cracks, missing parts or an uncertain configuration require assessment. Do not weld extensions, drill new height holes or substitute beams without approved design and instructions.

Configuration example

A supplied portable frame is rated 4,000 lb at one height/span and 3,000 lb at a taller, wider condition. The proposed 3,500-lb total carried load fits the first rating but not the second. Raising the frame to gain clearance changes the permissible condition; its original headline rating does not remain available automatically.

Coordinate operation

Position the load beneath the approved lifting line, take tension slowly and verify the frame and trolley remain stable. Maintain signals where the operator cannot see the relevant motion. Observe the floor and supports as the reaction changes through travel.

Manual pushing should occur only from the prescribed safe position and method. Do not push directly on a suspended payload in a way that creates uncontrolled swing or puts people in crush zones. Geared or powered trolley controls require the same deliberate command and stopping discipline.

At the destination, land on prepared supports and release only after stability is established. Park and secure the trolley or frame according to instructions before disconnecting equipment. For storage or disassembly, follow the approved sequence so removal of one brace does not destabilize remaining members.

The exam lesson is compatibility across the complete support system. Frame capacity, beam strength, flange fit, hoist weight, travel permission and stability all matter; no single nameplate substitutes for the others.

Sources: CCO A-frame and trolley topics , CMCO trolley and beam-clamp products , equipment catalog .