Study guide

16.1 Jacks, Toe Ratings and Positive Support

NCCCO Rigger Level II Exam

Track your progress as you read

Finished sections get a check mark.

1 Certification and Exam Preparation

1.1 Current Exam, Eligibility and Scheduling 1.2 Practical Tasks and Examination-Specific Rules 1.3 Study Method, References and Recertification

2 Identify and Measure the Load

2.1 Load Identity, Dimensions and Units 2.2 Load Weight, Density and Complete Inventories 2.3 Composition, Structural Integrity and Special Handling

3 Center of Gravity and Support Geometry

3.1 Center of Gravity and Suspended Stability 3.2 Attachment Points and Complete Force Paths 3.3 Final Position, Landing Supports and Derigging Access

4 Route and Site Hazards

4.1 Travel Path, Clearance and Work-Zone Control 4.2 Power Lines, Clearance Options and Electrical Response 4.3 Weather, Temperature and Ground Conditions

5 Team Duties and Communications

5.1 Signalperson Duties and Reliable Signals 5.2 Equipment Operator Duties and Capacity Decisions 5.3 Lift Director, Qualified Rigger and Hazard Communication

6 Equipment Requirements and Lift Planning

6.1 Determine Equipment Requirements and Compatibility 6.2 Written Plans, Sequence and Change Control 6.3 Critical-Lift Criteria, Risk and Contingencies

7 Balanced Sling Forces

7.1 Two-Leg Tension and Angle Reference 7.2 Length-to-Height Geometry and Headroom 7.3 Horizontal Forces and Attachment Demand

8 Composite and Unequal Loads

8.1 Composite Center of Gravity by Moments 8.2 Off-Center Reactions and Compatible Sling Geometry 8.3 Three- and Four-Leg Assemblies and Load Sharing

9 Wire Rope, Chain and Metal Mesh Slings

9.1 Select and Use Wire-Rope Slings 9.2 Alloy-Chain Assemblies and Approved Adjustment 9.3 Metal-Mesh Slings: Selection, Contact and Removal

10 Synthetic Rope, Web and Roundslings

10.1 Synthetic-Rope Slings and Approved Splices 10.2 Synthetic-Web Slings and Material Compatibility 10.3 Roundslings, Core Protection and Performance Fibers

11 Hitch Application and Sling Protection

11.1 Vertical and Basket Hitch Capacity 11.2 Choker Hitches, Choke Angle and Bundles 11.3 Softeners, Bend Protection and Cut Protection

12 Shackles, Hooks and Collector Hardware

12.1 Shackle Types, Pin Seating and Side Loading 12.2 Hooks, Latches and Permitted Load Seating 12.3 Master Links, Rings and Swivels

13 Threaded Points and Adjustable Hardware

13.1 Eyebolts, Shoulder Seating and Angular Demand 13.2 Swivel Hoist Rings and Installation Torque 13.3 Turnbuckles and Chain Hardware in Adjustable Systems

14 Compression Hardware and Rigging Blocks

14.1 Wire-Rope Clips and Permitted Terminations 14.2 Wedge Sockets, Rope Alignment and Tail Security 14.3 Rigging Blocks, Resultants and Reeving

15 Manual, Lever and Powered Hoists

15.1 Manual Chain Falls and Vertical Hoisting 15.2 Lever Hoists, Pulling Direction and Controlled Adjustment 15.3 Air and Electric Hoists: Supply, Duty and Controls

16 Jacks, Rollers and Portable Supports

16.1 Jacks, Toe Ratings and Positive Support 16.2 Dollies, Skates, Rollers and Horizontal Control 16.3 A-Frames, Gantries and Trolley Compatibility

17 Structural Lifters and Clamps

17.1 Lifting Beams, Spreaders and Configuration Ratings 17.2 Plate Clamps, Material Limits and Grip Conditions 17.3 Beam Clamps as Attachments and Beam/Girder Lifters

18 Mechanical, Vacuum and Magnetic Devices

18.1 Mechanical and Vacuum Lifting Devices 18.2 Close-Proximity and Remotely Operated Lifting Magnets 18.3 Scrap and Material-Handling Grapples

19 Inspection, Removal and Records

19.1 Inspecting All Six Sling Families 19.2 Hook and Rigging-Hardware Inspection 19.3 Below-the-Hook Device Inspection and Testing

20 Lift Control, Rotation and Completion

20.1 Take-Up, Trial Lift and Load Control 20.2 Controlled Rotation, Upending and Multiple-Crane Lifts 20.3 Secure the Load, Remove Rigging and Stow Equipment

21 Technical Standards and Crane Capacity

21.1 Apply the Correct Standard and Regulatory Scope 21.2 Crane Charts, Suspended Weight and Capacity Deductions 21.3 Personnel Hoisting Under OSHA 1926.1431

16.1 Jacks, Toe Ratings and Positive Support

Key Takeaways Explain This Topic AI

Toe rating is product specific, not universally half the head rating.

Multiple jacks do not automatically share equally.

Provide approved positive support before exposing people beneath a load.

Last updated: October 2026

Select the actual jacking configuration

A jack raises a load through a limited stroke or controlled mechanical movement. Bottle jacks, low-profile cylinders, toe jacks, screw jacks and locknut cylinders have different access and support characteristics. Select the product for the actual lifting point, demand, stroke and operating conditions.

A toe jack can engage a low lifting surface where a top saddle will not fit. Its toe rating can differ from its head rating, but there is no universal rule that every toe has exactly 50% of head capacity. Use the separate ratings on the actual product. Some models have different relationships, so a remembered percentage is not a safe substitute for identification.

A jack’s rating does not establish the strength of the payload contact point or floor. Local force can damage a thin base or concentrate load into an unsuitable surface. Confirm an approved lifting point and adequate support beneath the jack, including resistance to sliding and overturning.

Check access, stroke and alignment

The jack must fit beneath the approved contact with room for safe installation and operation. Its available stroke must complete the planned stage while preserving a controlled support sequence. Reaching the end of stroke with the load unsupported is a planning failure.

  • Jack selection item Required assessment
  • Toe or head Use the actual rating for the contact used
  • Starting clearance Verify physical access without improvisation
  • Stroke Complete the stage and planned support transfer
  • Base and floor Carry concentrated reaction and maintain alignment
  • Load contact Use approved strength and bearing geometry
  • Control and holding Follow the product’s mechanism and failure procedures

Apply force in the permitted direction. Side loading or an eccentric contact can destabilize the jack or damage its mechanism. Do not add an unapproved buffer or saddle that creates slipping or eccentricity. Manufacturer accessories must be installed as specified.

Follow the load with planned support

Hydraulic pressure alone is not a safe reason to place a body part beneath the load. Provide positive support through approved blocking, mechanical locks or another rated method before work in a position exposed to a dropped load. The plan must determine how support follows each stage of movement.

There is no universal instruction that one inch of lift always requires a particular timber thickness or that every crib stack may be three times its base width. Blocking design depends on material, bearing area, geometry, height, lateral stability and the load’s support points. Use an approved support arrangement rather than a generic ratio.

A locknut cylinder can provide mechanical holding when its nut is properly engaged under the manufacturer procedure. This does not mean every jack with a threaded part has a load-bearing lock or that pressure can be released arbitrarily. Confirm the designed function and transfer sequence.

Calculate reactions rather than dividing by jack count

Several jacks beneath a load do not automatically share equally. CG location, support spacing, stiffness and differing movement can concentrate force. A system lifting a rigid load at four points may need coordinated controls and monitoring to prevent distortion or overload.

For a simple two-support training model, a 36,000-lb load with CG one third of the span from the left support creates 24,000 lb left and 12,000 lb right. A given toe jack rated 20,000 lb cannot be used at the left support even if the pair’s combined ratings exceed total weight. The floor and payload contact must also accept their actual reactions.

Product-rating example

Assume a particular jack is labeled 30 tons at the head and 15 tons at the toe, with short tons defined as 2,000 lb. The toe capacity is 30,000 lb for that product. It cannot carry a proposed 36,000-lb toe reaction. The conclusion follows from the label, not a universal half-capacity rule.

Coordinate multiple-jack movement

Different stroke rates can tilt the load or redistribute forces. The approved method may use synchronized equipment, measurement and hold points. It is incorrect to claim every hydraulic gantry or multi-jack lift legally requires one exact PLC system or a universal 1/16-in synchronization tolerance.

Operators need clear commands and a plan for a failed hose, valve or power source. The response must follow the manufacturer’s supported procedures and preserve the load’s controlled condition. Do not improvise by loosening a hose or manually bleeding a loaded cylinder.

Inspect and operate deliberately

Inspect identification, contact parts, bases, ram or screw condition, hoses, controls, leaks and required safety features. A leaking hydraulic system or damaged screw requires assessment under the product criteria. Do not assume a check valve makes any defect safe.

Keep hands clear of pinch points during raising, blocking and lowering. Position blocks through an approved method without reaching beneath an unsupported load. Lower onto prepared supports in controlled stages and confirm stability before removing the jack. After use, inspect for damage and store with the manufacturer’s fluid, ram and corrosion-protection instructions.

The exam lesson is that the jack is one part of a load-transfer system. Correct toe/head rating, actual reaction, contact strength, foundation support and positive holding are all necessary.

Sources: CCO jack selection and execution scope , CMCO hydraulic and handling equipment .