Study guide

11.1 Vertical and Basket Hitch Capacity

NCCCO Rigger Level II Exam

Track your progress as you read

Finished sections get a check mark.

1 Certification and Exam Preparation

1.1 Current Exam, Eligibility and Scheduling 1.2 Practical Tasks and Examination-Specific Rules 1.3 Study Method, References and Recertification

2 Identify and Measure the Load

2.1 Load Identity, Dimensions and Units 2.2 Load Weight, Density and Complete Inventories 2.3 Composition, Structural Integrity and Special Handling

3 Center of Gravity and Support Geometry

3.1 Center of Gravity and Suspended Stability 3.2 Attachment Points and Complete Force Paths 3.3 Final Position, Landing Supports and Derigging Access

4 Route and Site Hazards

4.1 Travel Path, Clearance and Work-Zone Control 4.2 Power Lines, Clearance Options and Electrical Response 4.3 Weather, Temperature and Ground Conditions

5 Team Duties and Communications

5.1 Signalperson Duties and Reliable Signals 5.2 Equipment Operator Duties and Capacity Decisions 5.3 Lift Director, Qualified Rigger and Hazard Communication

6 Equipment Requirements and Lift Planning

6.1 Determine Equipment Requirements and Compatibility 6.2 Written Plans, Sequence and Change Control 6.3 Critical-Lift Criteria, Risk and Contingencies

7 Balanced Sling Forces

7.1 Two-Leg Tension and Angle Reference 7.2 Length-to-Height Geometry and Headroom 7.3 Horizontal Forces and Attachment Demand

8 Composite and Unequal Loads

8.1 Composite Center of Gravity by Moments 8.2 Off-Center Reactions and Compatible Sling Geometry 8.3 Three- and Four-Leg Assemblies and Load Sharing

9 Wire Rope, Chain and Metal Mesh Slings

9.1 Select and Use Wire-Rope Slings 9.2 Alloy-Chain Assemblies and Approved Adjustment 9.3 Metal-Mesh Slings: Selection, Contact and Removal

10 Synthetic Rope, Web and Roundslings

10.1 Synthetic-Rope Slings and Approved Splices 10.2 Synthetic-Web Slings and Material Compatibility 10.3 Roundslings, Core Protection and Performance Fibers

11 Hitch Application and Sling Protection

11.1 Vertical and Basket Hitch Capacity 11.2 Choker Hitches, Choke Angle and Bundles 11.3 Softeners, Bend Protection and Cut Protection

12 Shackles, Hooks and Collector Hardware

12.1 Shackle Types, Pin Seating and Side Loading 12.2 Hooks, Latches and Permitted Load Seating 12.3 Master Links, Rings and Swivels

13 Threaded Points and Adjustable Hardware

13.1 Eyebolts, Shoulder Seating and Angular Demand 13.2 Swivel Hoist Rings and Installation Torque 13.3 Turnbuckles and Chain Hardware in Adjustable Systems

14 Compression Hardware and Rigging Blocks

14.1 Wire-Rope Clips and Permitted Terminations 14.2 Wedge Sockets, Rope Alignment and Tail Security 14.3 Rigging Blocks, Resultants and Reeving

15 Manual, Lever and Powered Hoists

15.1 Manual Chain Falls and Vertical Hoisting 15.2 Lever Hoists, Pulling Direction and Controlled Adjustment 15.3 Air and Electric Hoists: Supply, Duty and Controls

16 Jacks, Rollers and Portable Supports

16.1 Jacks, Toe Ratings and Positive Support 16.2 Dollies, Skates, Rollers and Horizontal Control 16.3 A-Frames, Gantries and Trolley Compatibility

17 Structural Lifters and Clamps

17.1 Lifting Beams, Spreaders and Configuration Ratings 17.2 Plate Clamps, Material Limits and Grip Conditions 17.3 Beam Clamps as Attachments and Beam/Girder Lifters

18 Mechanical, Vacuum and Magnetic Devices

18.1 Mechanical and Vacuum Lifting Devices 18.2 Close-Proximity and Remotely Operated Lifting Magnets 18.3 Scrap and Material-Handling Grapples

19 Inspection, Removal and Records

19.1 Inspecting All Six Sling Families 19.2 Hook and Rigging-Hardware Inspection 19.3 Below-the-Hook Device Inspection and Testing

20 Lift Control, Rotation and Completion

20.1 Take-Up, Trial Lift and Load Control 20.2 Controlled Rotation, Upending and Multiple-Crane Lifts 20.3 Secure the Load, Remove Rigging and Stow Equipment

21 Technical Standards and Crane Capacity

21.1 Apply the Correct Standard and Regulatory Scope 21.2 Crane Charts, Suspended Weight and Capacity Deductions 21.3 Personnel Hoisting Under OSHA 1926.1431

11.1 Vertical and Basket Hitch Capacity

Key Takeaways Explain This Topic AI

Do not double a rating already labeled basket capacity.

A flatter symmetrical basket reduces available vertical support for a fixed portion limit.

An extra wrap does not create an extra capacity multiplier.

Last updated: October 2026

Identify the path carrying the load

A vertical hitch uses a sling as a single supporting connection. The sling carries the applied force along its load-bearing path. A basket hitch supports the load within the sling body with both ends connected above it. Those two portions can contribute support, but their angle, contact and balance determine the actual condition.

Do not count sling portions without examining the load path. A vertical leg attached to one lug remains a single leg even if its eye contains two visible sides. A basket contains two supporting body portions, but a displaced or unbalanced load can slide or change how those portions share. Hitch identity is a mechanical arrangement, not a count of visible fibers or rope segments.

Manufacturer tables commonly provide separate vertical and basket ratings. The basket value may assume vertical portions and a specified bend condition. Read its heading and notes. It is incorrect to state that every basket has exactly twice the vertical capacity regardless of geometry or to double a table value already labeled basket.

Resolve a symmetrical basket model

For a given basket with two equal supporting portions at horizontal angle θ, vertical equilibrium uses the same component reasoning as a balanced two-leg bridle. If the single-portion allowable tension is S and all other stated conditions are satisfied, the simple total vertical capacity is 2S sin θ. This is a model calculation, not a replacement for the manufacturer’s rated hitch information.

Assume a training table gives a 10,000-lb basket capacity for vertical portions, and explicitly directs applying sine of the horizontal angle for the described symmetrical geometry. At 60 degrees, the adjusted total is approximately 8,660 lb . At 45 degrees, it is approximately 7,071 lb . At 30 degrees, it is 5,000 lb .

  • Given vertical-basket baseline Horizontal angle Calculated training capacity
  • 10,000 lb 90° 10,000 lb
  • 10,000 lb 60° 8,660 lb
  • 10,000 lb 45° 7,071 lb
  • 10,000 lb 30° 5,000 lb

Multiplying by 1/sin θ would incorrectly increase basket capacity as the portions flatten. The reciprocal-sine factor is used to increase demanded tension from a vertical share. Sine can reduce available total vertical capacity from an explicitly stated baseline. These are related calculations performed in opposite directions.

Balance and retain the load

A basket does not grip every load automatically. The load must be supported so it cannot slip or roll out under the planned motion. Long members and bundles may need multiple baskets, positive retention or another approved arrangement. A narrow contact region can shift even when the initial lift looks balanced.

Locate support relative to the CG and consider changes during tilt. An object with a curved or tapered surface can migrate within the sling. A loose piece in a bundle may escape while the main group remains supported. The approved method must address all pieces, not merely the average bundle weight.

Double-wrap baskets can improve contact and resistance to movement in some approved uses, but an extra wrap does not multiply capacity again. The same load-bearing assembly and its rating remain relevant. More friction is not proof of positive retention through every rotation.

Bend and bearing conditions

A basket bends around the payload. Wire-rope D/d guidance, textile minimum bearing dimensions and metal-mesh contact requirements can affect suitability. The load’s surface may need compatible protection. If the manufacturer’s basket rating assumes a larger bend than the actual contact, obtain the correct adjusted rating or a different arrangement.

The eyes at the upper connection also need appropriate seating. A wide textile eye forced into a small hook can be unsuitable even when the body has a generous bend around the load. Check both contact locations and the complete sling length available for the geometry.

Application example

A 7,500-lb cylindrical load is proposed with the given 10,000-lb vertical-basket baseline at 45 degrees. Under the stated model, 7,071 lb is less than the demand, so the arrangement fails the numerical capacity check. A larger approved sling or a compatible geometry change is needed. The load’s cylinder shape also requires verified balance and retention before any rating comparison can approve execution.

Install and remove deliberately

Position the sling without twists or unapproved overlap, keep splice and fittings away from inappropriate contact, and preserve protection during take-up. Watch seating from a safe position during the planned trial lift. Unexpected movement requires a controlled stop and set-down for correction.

Plan support clearance for removal. A basket trapped beneath a landed payload must not be dragged free under load. After stable support and required restraints are verified, release tension and remove the sling without damaging it or destabilizing the object. This is part of choosing the hitch, not an issue to postpone until landing.

Source: CCO rigging reference booklet .