Study guide

15.2 Lever Hoists, Pulling Direction and Controlled Adjustment

NCCCO Rigger Level II Exam

Track your progress as you read

Finished sections get a check mark.

1 Certification and Exam Preparation

1.1 Current Exam, Eligibility and Scheduling 1.2 Practical Tasks and Examination-Specific Rules 1.3 Study Method, References and Recertification

2 Identify and Measure the Load

2.1 Load Identity, Dimensions and Units 2.2 Load Weight, Density and Complete Inventories 2.3 Composition, Structural Integrity and Special Handling

3 Center of Gravity and Support Geometry

3.1 Center of Gravity and Suspended Stability 3.2 Attachment Points and Complete Force Paths 3.3 Final Position, Landing Supports and Derigging Access

4 Route and Site Hazards

4.1 Travel Path, Clearance and Work-Zone Control 4.2 Power Lines, Clearance Options and Electrical Response 4.3 Weather, Temperature and Ground Conditions

5 Team Duties and Communications

5.1 Signalperson Duties and Reliable Signals 5.2 Equipment Operator Duties and Capacity Decisions 5.3 Lift Director, Qualified Rigger and Hazard Communication

6 Equipment Requirements and Lift Planning

6.1 Determine Equipment Requirements and Compatibility 6.2 Written Plans, Sequence and Change Control 6.3 Critical-Lift Criteria, Risk and Contingencies

7 Balanced Sling Forces

7.1 Two-Leg Tension and Angle Reference 7.2 Length-to-Height Geometry and Headroom 7.3 Horizontal Forces and Attachment Demand

8 Composite and Unequal Loads

8.1 Composite Center of Gravity by Moments 8.2 Off-Center Reactions and Compatible Sling Geometry 8.3 Three- and Four-Leg Assemblies and Load Sharing

9 Wire Rope, Chain and Metal Mesh Slings

9.1 Select and Use Wire-Rope Slings 9.2 Alloy-Chain Assemblies and Approved Adjustment 9.3 Metal-Mesh Slings: Selection, Contact and Removal

10 Synthetic Rope, Web and Roundslings

10.1 Synthetic-Rope Slings and Approved Splices 10.2 Synthetic-Web Slings and Material Compatibility 10.3 Roundslings, Core Protection and Performance Fibers

11 Hitch Application and Sling Protection

11.1 Vertical and Basket Hitch Capacity 11.2 Choker Hitches, Choke Angle and Bundles 11.3 Softeners, Bend Protection and Cut Protection

12 Shackles, Hooks and Collector Hardware

12.1 Shackle Types, Pin Seating and Side Loading 12.2 Hooks, Latches and Permitted Load Seating 12.3 Master Links, Rings and Swivels

13 Threaded Points and Adjustable Hardware

13.1 Eyebolts, Shoulder Seating and Angular Demand 13.2 Swivel Hoist Rings and Installation Torque 13.3 Turnbuckles and Chain Hardware in Adjustable Systems

14 Compression Hardware and Rigging Blocks

14.1 Wire-Rope Clips and Permitted Terminations 14.2 Wedge Sockets, Rope Alignment and Tail Security 14.3 Rigging Blocks, Resultants and Reeving

15 Manual, Lever and Powered Hoists

15.1 Manual Chain Falls and Vertical Hoisting 15.2 Lever Hoists, Pulling Direction and Controlled Adjustment 15.3 Air and Electric Hoists: Supply, Duty and Controls

16 Jacks, Rollers and Portable Supports

16.1 Jacks, Toe Ratings and Positive Support 16.2 Dollies, Skates, Rollers and Horizontal Control 16.3 A-Frames, Gantries and Trolley Compatibility

17 Structural Lifters and Clamps

17.1 Lifting Beams, Spreaders and Configuration Ratings 17.2 Plate Clamps, Material Limits and Grip Conditions 17.3 Beam Clamps as Attachments and Beam/Girder Lifters

18 Mechanical, Vacuum and Magnetic Devices

18.1 Mechanical and Vacuum Lifting Devices 18.2 Close-Proximity and Remotely Operated Lifting Magnets 18.3 Scrap and Material-Handling Grapples

19 Inspection, Removal and Records

19.1 Inspecting All Six Sling Families 19.2 Hook and Rigging-Hardware Inspection 19.3 Below-the-Hook Device Inspection and Testing

20 Lift Control, Rotation and Completion

20.1 Take-Up, Trial Lift and Load Control 20.2 Controlled Rotation, Upending and Multiple-Crane Lifts 20.3 Secure the Load, Remove Rigging and Stow Equipment

21 Technical Standards and Crane Capacity

21.1 Apply the Correct Standard and Regulatory Scope 21.2 Crane Charts, Suspended Weight and Capacity Deductions 21.3 Personnel Hoisting Under OSHA 1926.1431

15.2 Lever Hoists, Pulling Direction and Controlled Adjustment

Key Takeaways Explain This Topic AI

A load binder is not automatically an overhead-rated lever hoist.

Use free-chaining only under the product’s permitted unloaded conditions.

A longer handle does not increase WLL.

Last updated: October 2026

Select a rated lever-operated tool

A lever hoist uses a manually operated lever and ratchet or other mechanism to raise, lower or pull through its specified load chain or rope. It can be useful for controlled positioning and tensioning in approved directions. Its permitted orientations and functions depend on the product; not every lever tool is intended for overhead lifting or personnel use.

Identify rating, stroke or travel, hook type, chain or rope system and operating instructions. A load binder used to tighten transport chain is not a lever hoist merely because both have handles. The product’s function and qualification determine whether it can support a lifted load.

Lever mechanisms can produce large forces. Operator effort does not establish the load. A cheater bar or additional handle extension can exceed the intended input and damage the tool or supporting structure. Use only the manufacturer’s operating method; adding leverage is not a safe response to a difficult pull.

Align both ends of the force path

The upper attachment and lower hook must suit the actual pull direction and demand. Keep the load seated in the hooks’ intended bowls. Avoid tip, side and back loading. The tool needs space to align without its body or lever contacting an obstruction.

  • Lever-hoist check Failure mode addressed
  • Product approved for the task Prevents using a binder as a hoist
  • Matching chain or rope Preserves mechanism compatibility
  • Hook seating and alignment Avoids unintended bending
  • Adequate travel Prevents reaching a limit while still loaded
  • No handle extension Avoids uncontrolled input force
  • Secure supported load for changes Prevents sudden release during adjustment

A lever hoist used to pull horizontally still creates a force at its anchor. The anchor structure and connection must be rated for that direction. An overhead beam designed for vertical hoist suspension may not be approved for a large horizontal pull.

Free-chaining is not a loaded-release method

Some products provide a free-chaining or neutral feature for positioning the chain while unloaded. Its use conditions are specific. Do not operate it under load or assume it can safely release tension in a suspended system. Follow the manual’s transition between unloaded positioning and loaded operation.

Inspect the selector, hooks, chain, brake and mechanism according to the manufacturer. Incorrect reeving or a twisted chain can impair operation. A tool with damaged links, uncertain holding function or missing identification must be removed from use pending the proper process.

Do not use the load chain as a sling around the payload. The chain’s connection and mechanism are designed for their specified path. Attach suitable lower rigging to the hook instead of creating an unapproved chain hitch.

Plan tensioning and load transfer

A lever hoist can change geometry in a system with other slings or hoists. As one connection shortens, force can transfer into it or out of another support. The approved plan must establish permissible demand and the adjustment sequence. A tool’s rating alone does not show how much load it will acquire.

For example, a lever hoist used to restrain a turn near its tipping transition can see substantial force. Its anchor, sling angle and line of action determine that force. It is not automatically “only a tagline” because it does not carry the entire vertical weight.

If a load is being transferred between supports, identify when each connection carries weight and what verifies the transfer. A visually slack sling may still become tensioned as the object moves. Avoid removing a connection until the approved supported state is established.

Pulling-force example

A training move supplies an estimated 4,000-lb required horizontal pull and a lever hoist rated 3,000 lb for that application. The tool is insufficient. Attaching a longer handle does not increase its allowable load; it merely enables greater input. Choose an adequate approved system and verify the anchor, route and stopping method.

The same reasoning applies if the load is unexpectedly stuck. Required pull can exceed the estimate because of an obstruction or changed friction. Stop and reassess rather than treating extra hand effort as harmless.

Keep the operator out of the hazard path

Position the operator to use the lever without standing beneath the suspended load or in line with a possible released connection. Keep hands away from the chain, hooks and pinch points. Establish communication with other operators and the designated signalperson where coordinated movement is required.

Operate smoothly and stop for abnormal noise, slipping, binding or unexpected motion. Place the load in a safe condition through the approved procedure and remove defective equipment from use. Do not disassemble a loaded brake or release mechanism to cure a jam.

After use, unload and store the tool as instructed, protecting chain, hooks and controls. Record defects and keep removed equipment separated. A compact hand-operated tool deserves the same force-path and condition discipline as a larger powered machine.

Sources: CCO lever-hoist scope , CMCO lever-hoist manuals .