Study guide
19.2 Hook and Rigging-Hardware Inspection
NCCCO Rigger Level II Exam
Track your progress as you read
Finished sections get a check mark.
1 Certification and Exam Preparation
1.1 Current Exam, Eligibility and Scheduling 1.2 Practical Tasks and Examination-Specific Rules 1.3 Study Method, References and Recertification
2 Identify and Measure the Load
2.1 Load Identity, Dimensions and Units 2.2 Load Weight, Density and Complete Inventories 2.3 Composition, Structural Integrity and Special Handling
3 Center of Gravity and Support Geometry
3.1 Center of Gravity and Suspended Stability 3.2 Attachment Points and Complete Force Paths 3.3 Final Position, Landing Supports and Derigging Access
4 Route and Site Hazards
4.1 Travel Path, Clearance and Work-Zone Control 4.2 Power Lines, Clearance Options and Electrical Response 4.3 Weather, Temperature and Ground Conditions
5 Team Duties and Communications
5.1 Signalperson Duties and Reliable Signals 5.2 Equipment Operator Duties and Capacity Decisions 5.3 Lift Director, Qualified Rigger and Hazard Communication
6 Equipment Requirements and Lift Planning
6.1 Determine Equipment Requirements and Compatibility 6.2 Written Plans, Sequence and Change Control 6.3 Critical-Lift Criteria, Risk and Contingencies
7 Balanced Sling Forces
7.1 Two-Leg Tension and Angle Reference 7.2 Length-to-Height Geometry and Headroom 7.3 Horizontal Forces and Attachment Demand
8 Composite and Unequal Loads
8.1 Composite Center of Gravity by Moments 8.2 Off-Center Reactions and Compatible Sling Geometry 8.3 Three- and Four-Leg Assemblies and Load Sharing
9 Wire Rope, Chain and Metal Mesh Slings
9.1 Select and Use Wire-Rope Slings 9.2 Alloy-Chain Assemblies and Approved Adjustment 9.3 Metal-Mesh Slings: Selection, Contact and Removal
10 Synthetic Rope, Web and Roundslings
10.1 Synthetic-Rope Slings and Approved Splices 10.2 Synthetic-Web Slings and Material Compatibility 10.3 Roundslings, Core Protection and Performance Fibers
11 Hitch Application and Sling Protection
11.1 Vertical and Basket Hitch Capacity 11.2 Choker Hitches, Choke Angle and Bundles 11.3 Softeners, Bend Protection and Cut Protection
12 Shackles, Hooks and Collector Hardware
12.1 Shackle Types, Pin Seating and Side Loading 12.2 Hooks, Latches and Permitted Load Seating 12.3 Master Links, Rings and Swivels
13 Threaded Points and Adjustable Hardware
13.1 Eyebolts, Shoulder Seating and Angular Demand 13.2 Swivel Hoist Rings and Installation Torque 13.3 Turnbuckles and Chain Hardware in Adjustable Systems
14 Compression Hardware and Rigging Blocks
14.1 Wire-Rope Clips and Permitted Terminations 14.2 Wedge Sockets, Rope Alignment and Tail Security 14.3 Rigging Blocks, Resultants and Reeving
15 Manual, Lever and Powered Hoists
15.1 Manual Chain Falls and Vertical Hoisting 15.2 Lever Hoists, Pulling Direction and Controlled Adjustment 15.3 Air and Electric Hoists: Supply, Duty and Controls
16 Jacks, Rollers and Portable Supports
16.1 Jacks, Toe Ratings and Positive Support 16.2 Dollies, Skates, Rollers and Horizontal Control 16.3 A-Frames, Gantries and Trolley Compatibility
17 Structural Lifters and Clamps
17.1 Lifting Beams, Spreaders and Configuration Ratings 17.2 Plate Clamps, Material Limits and Grip Conditions 17.3 Beam Clamps as Attachments and Beam/Girder Lifters
18 Mechanical, Vacuum and Magnetic Devices
18.1 Mechanical and Vacuum Lifting Devices 18.2 Close-Proximity and Remotely Operated Lifting Magnets 18.3 Scrap and Material-Handling Grapples
19 Inspection, Removal and Records
19.1 Inspecting All Six Sling Families 19.2 Hook and Rigging-Hardware Inspection 19.3 Below-the-Hook Device Inspection and Testing
20 Lift Control, Rotation and Completion
20.1 Take-Up, Trial Lift and Load Control 20.2 Controlled Rotation, Upending and Multiple-Crane Lifts 20.3 Secure the Load, Remove Rigging and Stow Equipment
21 Technical Standards and Crane Capacity
21.1 Apply the Correct Standard and Regulatory Scope 21.2 Crane Charts, Suspended Weight and Capacity Deductions 21.3 Personnel Hoisting Under OSHA 1926.1431
19.2 Hook and Rigging-Hardware Inspection
Key Takeaways Explain This Topic AI
Any visibly apparent hook bend or twist is addressed in CCO’s B30.10-2014 excerpt.
Measure throat change from the hook’s original dimension and apply the correct criterion.
A wrong pin or incorrectly assembled termination is a defect even without visible damage.
Last updated: October 2026
Identify the governing component standard
ASME B30.10 covers hooks; ASME B30.26 covers rigging hardware such as shackles, adjustable hardware, compression hardware, links, rings and swivels. Inspection includes identification, physical condition, assembly and function. A component can be structurally sound yet unsuitable because its pin is incorrect or its intended rating cannot be established.
The CCO study references identify B30.26-2015. The supplied CCO reference manual contains B30.10-2014 excerpts. These edition-specific exam references should be distinguished from the current applicable workplace standards and manufacturer instructions. Do not describe every numerical criterion as an undated universal rule.
Initial inspection checks new, repaired or altered equipment before use under the applicable program. Frequent inspection observes current condition and operation; periodic inspection is a thorough examination at the interval appropriate to service. Severe, corrosive or unusual service can require shorter intervals. An annual calendar reminder alone cannot prove a satisfactory inspection program for heavily used equipment.
Hooks: measure against the original condition
Inspect the bowl, throat, tip, shank, threads, swivel bearing, securing parts and latch or self-locking mechanism. Look for cracks, wear, gouges, deformation, corrosion, heat damage and unauthorized repairs. Compare measurements with manufacturer limits and the original dimensions, rather than an adjacent hook of unknown model.
The B30.10-2014 excerpt in CCO's manual identifies wear exceeding 10% of an original sectional dimension, unless the manufacturer recommends otherwise; any visibly apparent bend or twist; and distortion increasing throat opening by 5%, not to exceed 1/4 inch, unless the manufacturer recommends otherwise. It also addresses inability of a self-locking hook to lock. Do not keep a visibly twisted hook because it is below an unrelated numerical threshold.
OSHA 1910.184's alloy-chain hook provisions separately identify a throat opening more than 15% above normal or twist more than 10 degrees. Those stated OSHA values do not authorize use contrary to the applicable stricter ASME/manufacturer removal criteria. Always identify the source and application rather than combining the most permissive values from different documents.
Measurement example
A hook's original throat was 2.00 inches. Five percent is 0.10 inch, which is less than 0.25 inch. Under the supplied 5%-with-quarter-inch-cap criterion, an opening of 2.12 inches exceeds the 0.10-inch allowance. An opening of 2.07 inches would not exceed that numerical allowance, but cracks, wear or any visible distortion may independently require removal. Passing one measurement is not passing the complete inspection.
Latches and locking parts
A latch helps retain slack rigging; it does not carry the load or prove engagement. Test operation without placing fingers in the closing path. If a required latch is missing or inoperative, follow the approved repair or replacement procedure before use. Do not substitute tape, a zip tie or an arbitrary wire wrap.
CCO's B30.10 excerpt describes qualified approval of mousing for certain applications. That is a controlled provision with scope and requirements, not a universal repair instruction. Personnel-hoisting hooks have additional closed-and-locked requirements in OSHA 1926.1431. A hook acceptable for one material-handling application may therefore be unacceptable for a personnel platform.
Check swivel bearings and shank retention as well as the visible hook body. Reassembly must use the original securing method or manufacturer recommendations. A loose retaining nut or damaged thread is not cured by loading the hook so it seats tighter.
Inspect hardware by its mechanism
- Component Examine particularly
- Shackle Bow, pin, threads, holes, identification and correct matching pin
- Turnbuckle Body, end fittings, threads, engagement, locking and distortion
- Eyebolt/hoist ring Thread, shoulder or base seating, fasteners and permitted swivel/pivot function
- Link/ring/swivel Wear at bearing areas, deformation, cracks and freedom of intended movement
- Wire-rope clip Correct product, saddle/U-bolt or bridge, nuts, installation and rope condition
- Wedge socket Body, matched wedge, pin, rope routing, tail and seating
Check inaccessible bearing surfaces when the periodic procedure requires disassembly by an authorized person. Use manufacturer-specific dimensional and functional limits. A generic “10% wear allowed everywhere” statement does not establish continued usability for all hardware families.
Incorrect assembly is a defect even if every individual piece is undamaged. Examples include a mismatched shackle pin, insufficient turnbuckle thread engagement or a wedge socket with the live rope on the wrong side. Compare the complete installation to instructions. A proof-test certificate from before the mismatch does not validate the new assembly.
Record and resolve findings
Identify the component, finding, date and disposition under the inspection program. Separate it from usable stock and notify the responsible person. Manufacturer or qualified-person approval governs repair and modification where the standard permits them. Heating a bent hook, welding a shackle or grinding unknown cracks is not a routine rigger correction.
Authorized repairs require the applicable examination, testing and documentation before return to service. Maintain inspection records required by the relevant standard and employer program; do not claim that every pre-use visual observation requires the same written record as a periodic examination. Traceable equipment and clear disposition prevent rejected gear from reappearing in the next lift kit.
Sources: CCO reference manual, B30.10 excerpts , CCO B30.26 study reference , OSHA chain-sling provisions .