Study guide

13.1 Eyebolts, Shoulder Seating and Angular Demand

NCCCO Rigger Level II Exam

Track your progress as you read

Finished sections get a check mark.

1 Certification and Exam Preparation

1.1 Current Exam, Eligibility and Scheduling 1.2 Practical Tasks and Examination-Specific Rules 1.3 Study Method, References and Recertification

2 Identify and Measure the Load

2.1 Load Identity, Dimensions and Units 2.2 Load Weight, Density and Complete Inventories 2.3 Composition, Structural Integrity and Special Handling

3 Center of Gravity and Support Geometry

3.1 Center of Gravity and Suspended Stability 3.2 Attachment Points and Complete Force Paths 3.3 Final Position, Landing Supports and Derigging Access

4 Route and Site Hazards

4.1 Travel Path, Clearance and Work-Zone Control 4.2 Power Lines, Clearance Options and Electrical Response 4.3 Weather, Temperature and Ground Conditions

5 Team Duties and Communications

5.1 Signalperson Duties and Reliable Signals 5.2 Equipment Operator Duties and Capacity Decisions 5.3 Lift Director, Qualified Rigger and Hazard Communication

6 Equipment Requirements and Lift Planning

6.1 Determine Equipment Requirements and Compatibility 6.2 Written Plans, Sequence and Change Control 6.3 Critical-Lift Criteria, Risk and Contingencies

7 Balanced Sling Forces

7.1 Two-Leg Tension and Angle Reference 7.2 Length-to-Height Geometry and Headroom 7.3 Horizontal Forces and Attachment Demand

8 Composite and Unequal Loads

8.1 Composite Center of Gravity by Moments 8.2 Off-Center Reactions and Compatible Sling Geometry 8.3 Three- and Four-Leg Assemblies and Load Sharing

9 Wire Rope, Chain and Metal Mesh Slings

9.1 Select and Use Wire-Rope Slings 9.2 Alloy-Chain Assemblies and Approved Adjustment 9.3 Metal-Mesh Slings: Selection, Contact and Removal

10 Synthetic Rope, Web and Roundslings

10.1 Synthetic-Rope Slings and Approved Splices 10.2 Synthetic-Web Slings and Material Compatibility 10.3 Roundslings, Core Protection and Performance Fibers

11 Hitch Application and Sling Protection

11.1 Vertical and Basket Hitch Capacity 11.2 Choker Hitches, Choke Angle and Bundles 11.3 Softeners, Bend Protection and Cut Protection

12 Shackles, Hooks and Collector Hardware

12.1 Shackle Types, Pin Seating and Side Loading 12.2 Hooks, Latches and Permitted Load Seating 12.3 Master Links, Rings and Swivels

13 Threaded Points and Adjustable Hardware

13.1 Eyebolts, Shoulder Seating and Angular Demand 13.2 Swivel Hoist Rings and Installation Torque 13.3 Turnbuckles and Chain Hardware in Adjustable Systems

14 Compression Hardware and Rigging Blocks

14.1 Wire-Rope Clips and Permitted Terminations 14.2 Wedge Sockets, Rope Alignment and Tail Security 14.3 Rigging Blocks, Resultants and Reeving

15 Manual, Lever and Powered Hoists

15.1 Manual Chain Falls and Vertical Hoisting 15.2 Lever Hoists, Pulling Direction and Controlled Adjustment 15.3 Air and Electric Hoists: Supply, Duty and Controls

16 Jacks, Rollers and Portable Supports

16.1 Jacks, Toe Ratings and Positive Support 16.2 Dollies, Skates, Rollers and Horizontal Control 16.3 A-Frames, Gantries and Trolley Compatibility

17 Structural Lifters and Clamps

17.1 Lifting Beams, Spreaders and Configuration Ratings 17.2 Plate Clamps, Material Limits and Grip Conditions 17.3 Beam Clamps as Attachments and Beam/Girder Lifters

18 Mechanical, Vacuum and Magnetic Devices

18.1 Mechanical and Vacuum Lifting Devices 18.2 Close-Proximity and Remotely Operated Lifting Magnets 18.3 Scrap and Material-Handling Grapples

19 Inspection, Removal and Records

19.1 Inspecting All Six Sling Families 19.2 Hook and Rigging-Hardware Inspection 19.3 Below-the-Hook Device Inspection and Testing

20 Lift Control, Rotation and Completion

20.1 Take-Up, Trial Lift and Load Control 20.2 Controlled Rotation, Upending and Multiple-Crane Lifts 20.3 Secure the Load, Remove Rigging and Stow Equipment

21 Technical Standards and Crane Capacity

21.1 Apply the Correct Standard and Regulatory Scope 21.2 Crane Charts, Suspended Weight and Capacity Deductions 21.3 Personnel Hoisting Under OSHA 1926.1431

13.1 Eyebolts, Shoulder Seating and Angular Demand

Key Takeaways Explain This Topic AI

Do not loosen an eyebolt simply to orient its eye.

Required engagement and shoulder seating are product specific.

Apply angular reductions to the actual leg tension, not just vertical weight share.

Last updated: October 2026

Identify the lifting point and mounting structure

An eyebolt provides an eye attached to a threaded shank. Its allowable load depends on product type, size, mounting material, engagement, installation and pull direction. An ordinary hardware-store eye or an unmarked bolt cannot be treated as a rated lifting point by appearance.

A plain or unshouldered eyebolt is generally restricted to its specified in-line loading. A shouldered eyebolt can permit angular loading under its manufacturer’s conditions, commonly with substantial reductions. Neither type accepts an arbitrary sideways pull through the eye. Read the product’s permitted direction and angle definition.

The object’s tapped hole is part of the load path. Its material, depth, thread condition and location must support the planned force. An adequately rated eyebolt in a thin, damaged or unapproved hole does not establish a sound attachment. Manufacturer installation requirements and the load’s handling approval must both be satisfied.

Seat the shoulder correctly

Where required, the shoulder must bear fully on a suitable flat surface. A gap, counterbore or uneven mounting face can introduce bending. Align the eye with the permitted pull plane using the manufacturer’s approved procedure. Do not back the eyebolt out merely to obtain convenient orientation.

Washers or shims may be permitted for particular products, but there is no universal allowance of “one thread pitch” for every eyebolt. Use the specified type, number and arrangement, maintaining required engagement and shoulder contact. Improvised stacks can change how the force enters the shank.

  • Installation check Reason
  • Correct product and thread Prevents an unqualified or mismatched attachment
  • Suitable mounting material Establishes force transfer into the load
  • Required engagement Avoids inadequate thread capacity
  • Shoulder seating Preserves the approved bearing condition
  • Eye alignment Prevents an unapproved out-of-plane pull

A shank bottoming in a blind hole can create a false impression of tightening while leaving the shoulder unsupported. Check the actual hole depth and engagement. Debris and damaged threads can produce the same false resistance. Additional wrench force is not a substitute for a suitable mounting condition.

Apply angular rating and sling demand separately

The sling angle determines demanded tension, while the eyebolt manufacturer’s angular rating determines available capacity. These are distinct operations. A 50% vertical share does not mean the eyebolt can be rated for half the payload without the sling-angle and mounting-direction checks.

For a training problem, assume a supplied shouldered eyebolt has 10,000-lb in-line WLL and a permitted 45-degree pull from its axis at 30% rating. Its available capacity in that stated condition is 3,000 lb . If actual inclined leg tension is 3,500 lb, the connection fails the numerical check. The 10,000-lb in-line rating cannot be used for the angular condition.

Do not apply the supplied 30% value to every eyebolt or every angle between zero and 45 degrees. Different products and angle definitions can have different tables. Manufacturer permission for one angular plane does not authorize perpendicular loading across the eye.

Avoid the common two-leg trap

Consider a balanced 8,000-lb load with two slings at 45 degrees from horizontal. Each vertical share is 4,000 lb, but each leg tension is approximately 5,657 lb . If the supplied angular eyebolt rating is only 3,000 lb, selecting two eyebolts does not make the system adequate. Both connections exceed their applicable limit.

The load’s lug or tapped structure must also be approved for the force direction. An eyebolt table cannot establish the strength of an unknown cast housing. If angular lifting is unsuitable, an approved hoist ring or redesigned attachment method may be appropriate, subject to its own installation and rating requirements.

Inspect and remove unsuitable points

Check identification, cracks, wear, bent shanks or eyes, damaged threads, corrosion and heat damage under the applicable criteria. A bent eye is not acceptable up to an invented ten-degree allowance. Do not straighten it or chase severely damaged threads to make installation possible.

Inspect the mounting area for cracking, thread damage and unsuitable contact. Remove or stop use when the required condition cannot be established. Replacing the eyebolt alone will not resolve a damaged hole or weakened surrounding material.

Field scenario

The eye points across the intended sling plane after its shoulder seats. The crew proposes loosening it half a turn. That creates an unsupported shoulder and may violate installation instructions. Use the manufacturer’s approved orientation method or a compatible lifting point, and confirm engagement and force direction. Do not let convenience override the mounting condition.

Keep threaded points protected when stored, and avoid damage to the eye or shank during removal. If lifting points remain installed after placement, follow the load manufacturer’s instructions for their subsequent use or protection. A point intended for a previous component configuration should not be assumed to rate the newly assembled system.

Sources: CCO eyebolt and hardware references , Crosby lifting-point instructions .