Study guide

3.2 Attachment Points and Complete Force Paths

NCCCO Rigger Level II Exam

Track your progress as you read

Finished sections get a check mark.

1 Certification and Exam Preparation

1.1 Current Exam, Eligibility and Scheduling 1.2 Practical Tasks and Examination-Specific Rules 1.3 Study Method, References and Recertification

2 Identify and Measure the Load

2.1 Load Identity, Dimensions and Units 2.2 Load Weight, Density and Complete Inventories 2.3 Composition, Structural Integrity and Special Handling

3 Center of Gravity and Support Geometry

3.1 Center of Gravity and Suspended Stability 3.2 Attachment Points and Complete Force Paths 3.3 Final Position, Landing Supports and Derigging Access

4 Route and Site Hazards

4.1 Travel Path, Clearance and Work-Zone Control 4.2 Power Lines, Clearance Options and Electrical Response 4.3 Weather, Temperature and Ground Conditions

5 Team Duties and Communications

5.1 Signalperson Duties and Reliable Signals 5.2 Equipment Operator Duties and Capacity Decisions 5.3 Lift Director, Qualified Rigger and Hazard Communication

6 Equipment Requirements and Lift Planning

6.1 Determine Equipment Requirements and Compatibility 6.2 Written Plans, Sequence and Change Control 6.3 Critical-Lift Criteria, Risk and Contingencies

7 Balanced Sling Forces

7.1 Two-Leg Tension and Angle Reference 7.2 Length-to-Height Geometry and Headroom 7.3 Horizontal Forces and Attachment Demand

8 Composite and Unequal Loads

8.1 Composite Center of Gravity by Moments 8.2 Off-Center Reactions and Compatible Sling Geometry 8.3 Three- and Four-Leg Assemblies and Load Sharing

9 Wire Rope, Chain and Metal Mesh Slings

9.1 Select and Use Wire-Rope Slings 9.2 Alloy-Chain Assemblies and Approved Adjustment 9.3 Metal-Mesh Slings: Selection, Contact and Removal

10 Synthetic Rope, Web and Roundslings

10.1 Synthetic-Rope Slings and Approved Splices 10.2 Synthetic-Web Slings and Material Compatibility 10.3 Roundslings, Core Protection and Performance Fibers

11 Hitch Application and Sling Protection

11.1 Vertical and Basket Hitch Capacity 11.2 Choker Hitches, Choke Angle and Bundles 11.3 Softeners, Bend Protection and Cut Protection

12 Shackles, Hooks and Collector Hardware

12.1 Shackle Types, Pin Seating and Side Loading 12.2 Hooks, Latches and Permitted Load Seating 12.3 Master Links, Rings and Swivels

13 Threaded Points and Adjustable Hardware

13.1 Eyebolts, Shoulder Seating and Angular Demand 13.2 Swivel Hoist Rings and Installation Torque 13.3 Turnbuckles and Chain Hardware in Adjustable Systems

14 Compression Hardware and Rigging Blocks

14.1 Wire-Rope Clips and Permitted Terminations 14.2 Wedge Sockets, Rope Alignment and Tail Security 14.3 Rigging Blocks, Resultants and Reeving

15 Manual, Lever and Powered Hoists

15.1 Manual Chain Falls and Vertical Hoisting 15.2 Lever Hoists, Pulling Direction and Controlled Adjustment 15.3 Air and Electric Hoists: Supply, Duty and Controls

16 Jacks, Rollers and Portable Supports

16.1 Jacks, Toe Ratings and Positive Support 16.2 Dollies, Skates, Rollers and Horizontal Control 16.3 A-Frames, Gantries and Trolley Compatibility

17 Structural Lifters and Clamps

17.1 Lifting Beams, Spreaders and Configuration Ratings 17.2 Plate Clamps, Material Limits and Grip Conditions 17.3 Beam Clamps as Attachments and Beam/Girder Lifters

18 Mechanical, Vacuum and Magnetic Devices

18.1 Mechanical and Vacuum Lifting Devices 18.2 Close-Proximity and Remotely Operated Lifting Magnets 18.3 Scrap and Material-Handling Grapples

19 Inspection, Removal and Records

19.1 Inspecting All Six Sling Families 19.2 Hook and Rigging-Hardware Inspection 19.3 Below-the-Hook Device Inspection and Testing

20 Lift Control, Rotation and Completion

20.1 Take-Up, Trial Lift and Load Control 20.2 Controlled Rotation, Upending and Multiple-Crane Lifts 20.3 Secure the Load, Remove Rigging and Stow Equipment

21 Technical Standards and Crane Capacity

21.1 Apply the Correct Standard and Regulatory Scope 21.2 Crane Charts, Suspended Weight and Capacity Deductions 21.3 Personnel Hoisting Under OSHA 1926.1431

3.2 Attachment Points and Complete Force Paths

Key Takeaways Explain This Topic AI

Check capacity, geometry, loading direction and retention together.

Inclined sling tension can exceed the vertical reaction at an attachment.

Never alter rated hardware to cure an incompatible fit.

Last updated: October 2026

Trace every connection

A force path follows the lifted weight from the payload through its attachments, slings, connecting hardware, lifting device and hoisting equipment. Every element must be suitable for its own demand. Selecting a master link rated for the total weight does not establish that each lower shackle can carry its inclined-leg tension or that a lug can resist the corresponding horizontal component.

Start with the intended attachment points on the load. Record their locations and permitted directions from drawings, manufacturer instructions or an approved handling plan. Identify whether they support the whole assembly, a removable component or a particular orientation. An eye intended for lifting a motor alone may be overloaded if used after a pump and base have been attached.

The connection must transmit force without binding , where hardware is prevented from aligning with the applied load. A shackle jammed between a lug and a stiffener may develop unintended bending. A hoist-ring bail touching the housing may be unable to pivot into the pull direction. The visible fit at rest is not enough; examine its position under tension and throughout any planned rotation.

Fit is different from rating

Four compatibility checks are particularly useful:

The component has sufficient applicable capacity for the calculated force.

Its dimensions permit proper seating and articulation.

Its loading direction is permitted by the manufacturer.

Its retention method prevents unintended disengagement during the maneuver.

A large shackle pin may not fit an approved lug hole. Substituting a smaller pin into the same shackle body does not preserve the original rating. A sling eye may be too small for the selected hook and become stretched across the tip. A wider bow may admit two eyes but create crowding that prevents them from finding their intended bearing position.

A lifting lug’s load direction matters in two planes. An inclined sling applies both upward and inward components. An out-of-plane pull can add bending at the lug plate and weld. The rigger must verify that the approved lug rating covers the actual resultant direction, rather than comparing only a vertical weight share with a vertical rating.

  • Interface Check before loading
  • Lug and shackle Correct pin, bearing contact, clearance and permitted pull plane
  • Sling eye and hook Eye seated in bowl, latch clear, no tip or side loading
  • Hoist ring and tapped hole Approved bolt, engagement, surface and torque
  • Sling and load edge Bend compatibility and adequate retained protection
  • Clamp and beam Correct flange range, direction and approved supporting structure
  • Include forces created by geometry

A 10,000-lb vertical reaction carried by a sling at 30 degrees from horizontal produces 20,000 lb of sling tension. That attachment also experiences an inward horizontal force in the simple model. A 10,000-lb vertical-only lug rating cannot automatically be treated as approval for the resulting inclined pull. The calculation and the component’s permitted loading must describe the same force.

Likewise, a redirect block’s anchor can carry more than the line pull. If equal-tension rope legs both pull the block in nearly the same direction, their forces add. The anchor hardware, sling and supporting structure must be evaluated for the resultant, not just the lifted weight or winch reading. The block chapter develops the calculation; force-path tracing identifies where the answer must be used.

Inspect the surrounding structure

A sound pin and properly seated shackle do not compensate for a cracked weld, corroded load plate or damaged threaded hole. Check the relevant supporting material and escalate defects to the responsible qualified person. There is no universal “10% padeye wear allowance” that a rigger can apply to every engineered lug without its inspection criteria.

For threaded lifting points, material strength and engagement determine whether the load can be transmitted into the object. Correct bolt diameter alone does not establish adequacy. The hole may be shallow, damaged, poorly aligned or located in an unapproved thin section. Manufacturer installation instructions and the object’s approved handling information must both be satisfied.

Connection review scenario

A crew chooses a 12-ton shackle for a lug carrying an estimated 8-ton inclined force. Its pin passes through the hole, but the bow touches a nearby flange before it aligns with the sling. The rating comparison alone looks acceptable. The geometry introduces binding, so the arrangement requires a compatible approved connection or a redesigned pick. Grinding the bow or enlarging the lug hole in the field is not a valid fit adjustment.

After installation, trace the path again with the actual parts and orientations. Confirm that screw pins are fully seated as instructed, bolt-type shackles have the required nuts and retaining pins, and adjustable hardware is secured according to its instructions. Review intermediate positions during a turn, where a fitting may rotate into contact even though both end positions appear clear.

This method avoids a common exam error: choosing the highest catalog rating while ignoring how force enters the component. The correct selection is the component and configuration that satisfy capacity, geometry, direction and retention together.

Sources: CCO reference materials , Crosby application information .